/dev/sda,megaraid_disk_04 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-72-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs Device Model: INTEL SSDSC2KB019T8 Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Firmware Version: XCV10132 User Capacity: 1,920,383,410,176 bytes [1.92 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 29 16:49:43 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 165 12 Power_Cycle_Count -O--CK 100 100 000 - 83 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 2513 (83 9905) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error_Count PO--CK 100 100 090 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Drive_Temperature -O---K 078 076 000 - 22 (Min/Max 18/27) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 194 Temperature_Celsius -O---K 100 100 000 - 22 197 Pending_Sector_Count -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 21238 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 0 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 2 228 Workload_Minutes -O--CK 100 100 000 - 9173 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Power_Loss_Cap_Test PO--CK 100 100 010 - 2513 (83 9905) 241 Host_Writes_32MiB -O--CK 100 100 000 - 21238 242 Host_Reads_32MiB -O--CK 100 100 000 - 438 243 NAND_Writes_32MiB -O--CK 100 100 000 - 33054 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 3336 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 18/27 Celsius Lifetime Min/Max Temperature: 7/27 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 83 --- Lifetime Power-On Resets 0x01 0x018 6 1391863012 --- Logical Sectors Written 0x01 0x020 6 2845050 --- Number of Write Commands 0x01 0x028 6 28708522 --- Logical Sectors Read 0x01 0x030 6 125802 --- Number of Read Commands 0x01 0x038 6 594354102 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 22 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 26 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 22 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 136 --- Number of Hardware Resets 0x06 0x010 4 129 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 15 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sda,megaraid_disk_05 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-72-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs Device Model: INTEL SSDSC2KB480G8 Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Firmware Version: XCV10132 User Capacity: 480,103,981,056 bytes [480 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 29 16:49:43 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 165 12 Power_Cycle_Count -O--CK 100 100 000 - 83 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 2423 (83 9905) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error_Count PO--CK 100 100 090 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Drive_Temperature -O---K 078 076 000 - 22 (Min/Max 18/26) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 194 Temperature_Celsius -O---K 100 100 000 - 22 197 Pending_Sector_Count -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 2881 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 0 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 9 228 Workload_Minutes -O--CK 100 100 000 - 9173 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Power_Loss_Cap_Test PO--CK 100 100 010 - 2423 (83 9905) 241 Host_Writes_32MiB -O--CK 100 100 000 - 2881 242 Host_Reads_32MiB -O--CK 100 100 000 - 267 243 NAND_Writes_32MiB -O--CK 100 100 000 - 5477 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 3336 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 18/26 Celsius Lifetime Min/Max Temperature: 7/32 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 83 --- Lifetime Power-On Resets 0x01 0x018 6 188822345 --- Logical Sectors Written 0x01 0x020 6 6943305 --- Number of Write Commands 0x01 0x028 6 17506956 --- Logical Sectors Read 0x01 0x030 6 8781591 --- Number of Read Commands 0x01 0x038 6 594334802 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 21 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 26 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 22 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 302 --- Number of Hardware Resets 0x06 0x010 4 174 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 30 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sda,megaraid_disk_06 smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-72-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel S4510/S4610/S4500/S4600 Series SSDs Device Model: INTEL SSDSC2KB480G8 Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Firmware Version: XCV10120 User Capacity: 480,103,981,056 bytes [480 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Apr 29 16:49:43 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: ATA return descriptor not supported by controller firmware Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART Status not supported: ATA return descriptor not supported by controller firmware SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 163 12 Power_Cycle_Count -O--CK 100 100 000 - 83 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 2679 (83 9813) 183 SATA_Downshift_Count -O--CK 100 100 000 - 0 184 End-to-End_Error_Count PO--CK 100 100 090 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Drive_Temperature -O---K 078 075 000 - 22 (Min/Max 19/26) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 80 194 Temperature_Celsius -O---K 100 100 000 - 22 197 Pending_Sector_Count -O--C- 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 0 225 Host_Writes_32MiB -O--CK 100 100 000 - 2881 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 0 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 7 228 Workload_Minutes -O--CK 100 100 000 - 9027 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 100 100 000 - 0 234 Thermal_Throttle_Status -O--CK 100 100 000 - 0/0 235 Power_Loss_Cap_Test PO--CK 100 100 010 - 2679 (83 9813) 241 Host_Writes_32MiB -O--CK 100 100 000 - 2881 242 Host_Reads_32MiB -O--CK 100 100 000 - 304 243 NAND_Writes_32MiB -O--CK 100 100 000 - 5449 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 8 Comprehensive SMART error log 0x03 GPL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x25 GPL R/O 512 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb8 GPL,SL VS 1 Device vendor specific log 0xb9 GPL VS 3336 Device vendor specific log 0xb9 SL VS 8 Device vendor specific log 0xba GPL VS 1280 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 8 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 19/26 Celsius Lifetime Min/Max Temperature: 7/33 Celsius Specified Max Operating Temperature: 73 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 2c 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Write SCT Data Table failed: SMART WRITE LOG SECTOR may cause problems, try with -T permissive to force Read SCT Temperature History failed Write SCT (Get) Error Recovery Control Command failed: ATA return descriptor not supported by controller firmware SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 83 --- Lifetime Power-On Resets 0x01 0x018 6 188820031 --- Logical Sectors Written 0x01 0x020 6 4533375 --- Number of Write Commands 0x01 0x028 6 19971628 --- Logical Sectors Read 0x01 0x030 6 4353263 --- Number of Read Commands 0x01 0x038 6 588782366 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 21 --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 26 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x030 1 22 --- Highest Average Short Term Temperature 0x05 0x038 1 21 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 73 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 276 --- Number of Hardware Resets 0x06 0x010 4 154 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x000a 4 30 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS