/dev/sda,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625fd6f Serial number: 44B667DAC5B154D45AE70C4C716DA6FF Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:01 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 11 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 11 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24604752 Blocks received from initiator = 8094968 Blocks read from cache and sent to initiator = 488272 Number of read and write commands whose size <= segment size = 15066 Number of read and write commands whose size > segment size = 11 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.00 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.598 0 write: 0 0 0 0 0 4.216 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:00 [2160 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625fd6d attached SAS address = 0x5001438037c40500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625fd6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,hpsa_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625f983 Serial number: 7B6B09633A8C8ECFC8F3511BA4CC4A76 Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:02 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 13 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 13 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 25201160 Blocks received from initiator = 7991144 Blocks read from cache and sent to initiator = 466267 Number of read and write commands whose size <= segment size = 14904 Number of read and write commands whose size > segment size = 9 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.05 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.903 0 write: 0 0 0 0 0 4.167 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:03 [2163 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625f981 attached SAS address = 0x5001438037c40500 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625f982 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,hpsa_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625b8e7 Serial number: 304815F1CCD9844D350B53324AA3902F Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:04 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 12 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 12 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24474384 Blocks received from initiator = 8062896 Blocks read from cache and sent to initiator = 403470 Number of read and write commands whose size <= segment size = 15201 Number of read and write commands whose size > segment size = 10 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.17 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.531 0 write: 0 0 0 0 0 4.203 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:10 [2170 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625b8e5 attached SAS address = 0x5001438037c40500 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625b8e6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,hpsa_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625bbb7 Serial number: 12E7179F6B3EF277268AC58481B22B7A Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:05 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 12 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 12 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24653200 Blocks received from initiator = 8117784 Blocks read from cache and sent to initiator = 382016 Number of read and write commands whose size <= segment size = 15239 Number of read and write commands whose size > segment size = 11 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.17 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.622 0 write: 0 0 0 0 0 4.232 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:10 [2170 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625bbb5 attached SAS address = 0x5001438037c40500 attached phy identifier = 3 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625bbb6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sda,hpsa_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 3.56 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sda,hpsa_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_14 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sda,hpsa_disk_15 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sda [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_00 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625fd6f Serial number: 44B667DAC5B154D45AE70C4C716DA6FF Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:07 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 11 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 11 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24627544 Blocks received from initiator = 8095640 Blocks read from cache and sent to initiator = 490213 Number of read and write commands whose size <= segment size = 15079 Number of read and write commands whose size > segment size = 11 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.00 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.609 0 write: 0 0 0 0 0 4.217 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:00 [2160 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625fd6d attached SAS address = 0x5001438037c40500 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625fd6e attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sg0,hpsa_disk_01 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625f983 Serial number: 7B6B09633A8C8ECFC8F3511BA4CC4A76 Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:08 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 37 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 13 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 13 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 25201160 Blocks received from initiator = 7991192 Blocks read from cache and sent to initiator = 466267 Number of read and write commands whose size <= segment size = 14906 Number of read and write commands whose size > segment size = 9 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.05 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.903 0 write: 0 0 0 0 0 4.167 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:04 [2164 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625f981 attached SAS address = 0x5001438037c40500 attached phy identifier = 1 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625f982 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sg0,hpsa_disk_02 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625b8e7 Serial number: 304815F1CCD9844D350B53324AA3902F Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:09 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 12 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 12 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24474384 Blocks received from initiator = 8063072 Blocks read from cache and sent to initiator = 403470 Number of read and write commands whose size <= segment size = 15205 Number of read and write commands whose size > segment size = 10 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.17 number of minutes until next internal SMART test = 56 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.531 0 write: 0 0 0 0 0 4.204 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:10 [2170 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625b8e5 attached SAS address = 0x5001438037c40500 attached phy identifier = 2 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625b8e6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sg0,hpsa_disk_03 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: SEAGATE Product: ST10000NM018B Revision: E002 Compliance: SPC-5 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Logical block size: 512 bytes Physical block size: 4096 bytes LU is fully provisioned Rotation Rate: 7200 rpm Form Factor: 3.5 inches Logical Unit id: 0x5000c500f625bbb7 Serial number: 12E7179F6B3EF277268AC58481B22B7A Device type: disk Transport protocol: SAS (SPL-4) Local Time is: Fri May 3 17:35:10 2024 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled Temperature Warning: Enabled Read Cache is: Enabled Writeback Cache is: Disabled === START OF READ SMART DATA SECTION === SMART Health Status: OK Grown defects during certification <not available> Total blocks reassigned during format <not available> Total new blocks reassigned <not available> Power on minutes since format <not available> Current Drive Temperature: 36 C Drive Trip Temperature: 60 C Manufactured in week 43 of year 2023 Specified cycle count over device lifetime: 50000 Accumulated start-stop cycles: 12 Specified load-unload count over device lifetime: 600000 Accumulated load-unload cycles: 12 Elements in grown defect list: 0 Vendor (Seagate Cache) information Blocks sent to initiator = 24653200 Blocks received from initiator = 8117864 Blocks read from cache and sent to initiator = 382016 Number of read and write commands whose size <= segment size = 15242 Number of read and write commands whose size > segment size = 11 Vendor (Seagate/Hitachi) factory information number of hours powered up = 36.17 number of minutes until next internal SMART test = 57 Error counter log: Errors Corrected by Total Correction Gigabytes Total ECC rereads/ errors algorithm processed uncorrected fast | delayed rewrites corrected invocations [10^9 bytes] errors read: 0 0 0 0 0 12.622 0 write: 0 0 0 0 0 4.232 0 Non-medium error count: 0 Pending defect count:0 Pending Defects [GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on'] No Self-tests have been logged Background scan results log Status: no scans active Accumulated power on time, hours:minutes 36:10 [2170 minutes] Number of background scans performed: 0, scan progress: 0.00% Number of background medium scans performed: 0 Protocol Specific port log page for SAS SSP relative target port id = 1 generation code = 0 number of phys = 1 phy identifier = 0 attached device type: SAS or SATA device attached reason: unknown reason: loss of dword synchronization negotiated logical link rate: phy enabled; 12 Gbps attached initiator port: ssp=1 stp=1 smp=1 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625bbb5 attached SAS address = 0x5001438037c40500 attached phy identifier = 3 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 2 Phy reset problem count = 2 relative target port id = 2 generation code = 0 number of phys = 1 phy identifier = 1 attached device type: no device attached attached reason: unknown reason: unknown negotiated logical link rate: phy enabled; unknown attached initiator port: ssp=0 stp=0 smp=0 attached target port: ssp=0 stp=0 smp=0 SAS address = 0x5000c500f625bbb6 attached SAS address = 0x0 attached phy identifier = 0 Invalid DWORD count = 0 Running disparity error count = 0 Loss of DWORD synchronization count = 0 Phy reset problem count = 0 /dev/sg0,hpsa_disk_04 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Vendor: HP Product: P440ar Revision: 3.56 Compliance: SPC-3 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. /dev/sg0,hpsa_disk_05 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_05] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_06 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_06] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_07 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_07] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_08 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_08] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_09 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_09] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_10 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_10] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_11 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_11] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_12 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_12] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_13 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_13] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_14 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_14] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address /dev/sg0,hpsa_disk_15 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.8.4-2-pve] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org Smartctl open device: /dev/sg0 [cciss_disk_15] [SCSI/SAT] failed: INQUIRY [SAT]: No such device or address