Probe #fecfd149c1 of ASUSTek M2A-VM Desktop Computer

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3250310AS Serial Number: -- Firmware Version: 3.AAF User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon May 21 22:17:46 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 64) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 098 098 020 - 2662 5 Reallocated_Sector_Ct PO--CK 099 099 036 - 77 7 Seek_Error_Rate POSR-- 083 060 030 - 213824937 9 Power_On_Hours -O--CK 091 091 000 - 7985 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 098 098 020 - 2702 187 Reported_Uncorrect -O--CK 001 001 000 - 299 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 057 040 045 Past 43 (Min/Max 18/60 #7) 194 Temperature_Celsius -O---K 043 060 000 - 43 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 072 053 000 - 216515847 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 148 000 - 511 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1179 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1179 [18] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0e 03 00 8e e7 e0 00 00:41:15.270 WRITE DMA EXT 25 00 00 00 20 00 06 8c 00 1f dc e0 00 00:41:27.669 READ DMA EXT 35 00 00 00 08 00 00 2d 00 60 8f e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 10 00 00 5e 00 5f 17 e0 00 00:41:27.651 WRITE DMA EXT Error 1178 [17] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 10 00 0e 04 00 8e 77 e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 2d 00 60 57 e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 5e 37 e0 00 00:41:15.270 WRITE DMA EXT Error 1177 [16] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:41:15.270 WRITE DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:41:15.270 READ DMA EXT 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:15.270 READ DMA EXT Error 1176 [15] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:31.847 READ DMA EXT 35 00 00 00 08 00 0f 60 00 03 4f e0 00 00:41:31.823 WRITE DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 02 00 04 79 00 09 ef e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 08 00 00 2d 00 60 af e0 00 00:41:27.651 WRITE DMA EXT Error 1175 [14] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0e 03 00 8e e7 e0 00 00:41:15.270 WRITE DMA EXT 25 00 00 00 20 00 06 8c 00 1f dc e0 00 00:41:27.669 READ DMA EXT 35 00 00 00 08 00 00 2d 00 60 8f e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 10 00 00 5e 00 5f 17 e0 00 00:41:27.651 WRITE DMA EXT Error 1174 [13] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 10 00 0e 04 00 8e 77 e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 2d 00 60 57 e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 5e 37 e0 00 00:41:15.270 WRITE DMA EXT Error 1173 [12] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:19.375 READ DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:15.270 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:41:15.270 WRITE DMA EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:41:15.270 READ DMA EXT 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:15.270 READ DMA EXT Error 1172 [11] occurred at disk power-on lifetime: 6346 hours (264 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 14 e2 00 9f 49 e0 00 Error: UNC at LBA = 0x14e2009f49 = 89691037513 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 14 e2 00 9f 47 e0 00 00:41:31.847 READ DMA EXT 35 00 00 00 08 00 0f 60 00 03 4f e0 00 00:41:31.823 WRITE DMA EXT 35 00 00 00 08 00 0f 98 00 02 df e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 02 00 04 79 00 09 ef e0 00 00:41:27.669 WRITE DMA EXT 35 00 00 00 08 00 00 2d 00 60 af e0 00 00:41:27.651 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 521 (0x0209) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Max Temperature: 0 Celsius Lifetime Max Temperature: 0 Celsius SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x8002 2 0 Vendor specific 0x8003 2 1 Vendor specific 0x8004 2 0 Vendor specific


Hardware for Linux and BSD

GitHub