/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.10.6+bpo-amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37480G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: SBFK61K1 User Capacity: 480,103,981,056 bytes [480 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 9 14:08:58 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 15398 12 Power_Cycle_Count -O--CK 100 100 000 - 1429 148 Unknown_Attribute ------ 100 100 000 - 0 149 Unknown_Attribute ------ 100 100 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 22 170 Bad_Blk_Ct_Lat/Erl ------ 100 100 010 - 0/107 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 65 (Average 30) 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 118 194 Temperature_Celsius -O---K 029 043 000 - 29 (Min/Max 17/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count -O--CK 100 100 000 - 55883 231 SSD_Life_Left ------ 097 097 000 - 97 233 Flash_Writes_GiB -O--CK 100 100 000 - 12537 241 Lifetime_Writes_GiB -O--CK 100 100 000 - 13390 242 Lifetime_Reads_GiB -O--CK 100 100 000 - 39671 244 Average_Erase_Count ------ 100 100 000 - 30 245 Max_Erase_Count ------ 100 100 000 - 65 246 Total_Erase_Count ------ 100 100 000 - 1332864 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 54400 (device log contains only the most recent 256 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 54400 [127] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 96 bc e0 e0 00 Error: ABRT at LBA = 0x2a96bce0 = 714521824 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 96 bc e0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 96 bb e0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 96 ba e0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 96 b9 e0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 8d 5f 70 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54399 [126] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 8d 5c 70 e0 00 Error: ABRT at LBA = 0x2a8d5c70 = 713907312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 8d 5c 70 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 8d 5c 70 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d5 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d3 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d4 00 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54398 [125] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 8d 5c 70 e0 00 Error: ABRT at LBA = 0x2a8d5c70 = 713907312 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 8d 5c 70 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d5 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d3 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d4 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d3 00 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54397 [124] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 82 d3 00 e0 00 Error: ABRT at LBA = 0x2a82d300 = 713216768 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 82 d3 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 82 d2 00 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 21 f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 20 f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 20 f0 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54396 [123] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 80 20 f0 e0 00 Error: ABRT at LBA = 0x2a8020f0 = 713040112 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 80 20 f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 1f f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 1e f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 80 1e f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 7f 1f d0 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54395 [122] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 2a 80 1e f0 e0 00 Error: ABRT at LBA = 0x2a801ef0 = 713039600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 2a 80 1e f0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 7f 1f d0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 7f 1e d0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 7f 1d d0 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 2a 7f 1c d0 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54394 [121] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 28 8f 6f f8 e0 00 Error: ABRT at LBA = 0x288f6ff8 = 680488952 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 28 8f 6f f8 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 28 85 a2 88 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 28 85 a1 88 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 28 85 a0 88 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 28 85 9f 88 e0 00 00:00:00.000 READ SECTOR(S) EXT Error 54393 [120] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 27 fd 8f 18 e0 00 Error: ABRT at LBA = 0x27fd8f18 = 670928664 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 24 00 00 01 00 00 00 27 fd 8f 18 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 27 fd 8f 18 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 27 fd 8e 18 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 27 fd 8d 18 e0 00 00:00:00.000 READ SECTOR(S) EXT 24 00 00 01 00 00 00 27 fd c5 98 e0 00 00:00:00.000 READ SECTOR(S) EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1429 --- Lifetime Power-On Resets 0x01 0x010 4 15398 --- Power-on Hours 0x01 0x018 6 28082393877 --- Logical Sectors Written 0x01 0x028 6 83197340843 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 55883 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 3 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 13 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 14 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.10.6+bpo-amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: KINGSTON SA400S37240G Serial Number: -- LU WWN Device Id: 5 0026b7 ... Firmware Version: SBFKB1H5 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3 T13/2161-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 9 14:08:58 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 000 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 25393 12 Power_Cycle_Count -O--CK 100 100 000 - 2186 148 Unknown_Attribute ------ 100 100 000 - 0 149 Unknown_Attribute ------ 100 100 000 - 0 167 Write_Protect_Mode ------ 100 100 000 - 0 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 169 Bad_Block_Rate ------ 100 100 000 - 11 170 Bad_Blk_Ct_Lat/Erl ------ 100 100 010 - 0/8 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 MaxAvgErase_Ct ------ 100 100 000 - 554 (Average 528) 181 Program_Fail_Count -O--CK 100 100 000 - 0 182 Erase_Fail_Count ------ 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 141 194 Temperature_Celsius -O---K 075 057 000 - 25 (Min/Max 17/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 SATA_CRC_Error_Count -O--CK 100 100 000 - 0 218 CRC_Error_Count -O--CK 100 100 000 - 0 231 SSD_Life_Left ------ 053 053 000 - 47 233 Flash_Writes_GiB -O--CK 100 100 000 - 80447 241 Lifetime_Writes_GiB -O--CK 100 100 000 - 40852 242 Lifetime_Reads_GiB -O--CK 100 100 000 - 105586 244 Average_Erase_Count ------ 100 100 000 - 528 245 Max_Erase_Count ------ 100 100 000 - 554 246 Total_Erase_Count ------ 100 100 000 - 4108112 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2186 --- Lifetime Power-On Resets 0x01 0x010 4 25393 --- Power-on Hours 0x01 0x018 6 85674006886 --- Logical Sectors Written 0x01 0x028 6 221431357811 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 25 --- Current Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 52 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 248 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 21 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.10.6+bpo-amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD3200BPVT-22JJ5T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Sep 9 14:08:58 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 74) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 136 133 021 - 2200 4 Start_Stop_Count -O--CK 046 046 000 - 54667 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 084 084 000 - 11691 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5983 191 G-Sense_Error_Rate -O--CK 001 001 000 - 3408 192 Power-Off_Retract_Count -O--CK 200 200 000 - 264 193 Load_Cycle_Count -O--CK 106 106 000 - 284087 194 Temperature_Celsius -O---K 114 094 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 001 000 - 468 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 194 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 194 [1] occurred at disk power-on lifetime: 11641 hours (485 days + 1 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 12:05:52.820 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 12:05:52.819 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:52.816 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:52.472 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:50.434 IDENTIFY DEVICE Error 193 [0] occurred at disk power-on lifetime: 11641 hours (485 days + 1 hours) When the command that caused the error occurred, the device was in standby mode. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 a0 00 12:05:52.819 SMART WRITE LOG ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:52.816 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:52.472 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:50.434 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 00 12:05:48.480 IDENTIFY DEVICE Error 192 [23] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.712 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.711 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.710 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.708 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.707 SMART WRITE LOG Error 191 [22] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.711 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.710 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.708 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.707 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.706 SMART WRITE LOG Error 190 [21] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.710 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.708 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.707 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.706 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.702 SMART WRITE LOG Error 189 [20] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.708 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.707 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.706 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.702 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.701 SMART WRITE LOG Error 188 [19] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.707 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.706 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.702 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.701 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.700 SMART WRITE LOG Error 187 [18] occurred at disk power-on lifetime: 5344 hours (222 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 01 00 00 00 00 00 00 40 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.706 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.702 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.701 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.700 SMART WRITE LOG b0 00 d6 00 01 00 00 00 c2 4f e0 40 00 03:31:18.698 SMART WRITE LOG SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 20/29 Celsius Lifetime Min/Max Temperature: -1/50 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (29) Index Estimated Time Temperature Celsius 30 2024-09-09 12:01 26 ******* ... ..( 12 skipped). .. ******* 43 2024-09-09 12:14 26 ******* 44 2024-09-09 12:15 ? - 45 2024-09-09 12:16 26 ******* ... ..( 22 skipped). .. ******* 68 2024-09-09 12:39 26 ******* 69 2024-09-09 12:40 ? - 70 2024-09-09 12:41 26 ******* 71 2024-09-09 12:42 26 ******* 72 2024-09-09 12:43 ? - 73 2024-09-09 12:44 20 * 74 2024-09-09 12:45 21 ** 75 2024-09-09 12:46 22 *** 76 2024-09-09 12:47 23 **** 77 2024-09-09 12:48 23 **** 78 2024-09-09 12:49 23 **** 79 2024-09-09 12:50 24 ***** 80 2024-09-09 12:51 24 ***** 81 2024-09-09 12:52 25 ****** 82 2024-09-09 12:53 25 ****** 83 2024-09-09 12:54 26 ******* ... ..( 3 skipped). .. ******* 87 2024-09-09 12:58 26 ******* 88 2024-09-09 12:59 27 ******** ... ..( 4 skipped). .. ******** 93 2024-09-09 13:04 27 ******** 94 2024-09-09 13:05 28 ********* ... ..( 14 skipped). .. ********* 109 2024-09-09 13:20 28 ********* 110 2024-09-09 13:21 29 ********** ... ..( 46 skipped). .. ********** 29 2024-09-09 14:08 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4119 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 5278 Vendor specific /dev/sdd smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.10.6+bpo-amd64] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA200 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MX4OABB0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Sep 9 14:08:58 2024 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14822) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 247) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 139 139 054 - 72 3 Spin_Up_Time POS--- 126 126 024 - 301 (Average 301) 4 Start_Stop_Count -O--C- 095 095 000 - 20711 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 124 124 020 - 33 9 Power_On_Hours -O--C- 093 093 000 - 54130 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 4946 192 Power-Off_Retract_Count -O--CK 083 083 000 - 20901 193 Load_Cycle_Count -O--C- 083 083 000 - 20901 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 11/43) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 621 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 621 [0] occurred at disk power-on lifetime: 35122 hours (1463 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 03 c1 a9 f0 03 00 Error: UNC at LBA = 0x03c1a9f0 = 63023600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 58 00 00 3b cb 56 88 40 00 09:09:50.244 READ FPDMA QUEUED 60 00 38 00 50 00 00 3b c7 d0 e8 40 00 09:09:50.244 READ FPDMA QUEUED 60 00 08 00 48 00 00 3b d8 ab 18 40 00 09:09:50.243 READ FPDMA QUEUED 60 00 08 00 40 00 00 03 c1 f8 78 40 00 09:09:50.243 READ FPDMA QUEUED 60 00 07 00 38 00 00 03 c1 f8 70 40 00 09:09:50.243 READ FPDMA QUEUED Error 620 [3] occurred at disk power-on lifetime: 35122 hours (1463 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 03 c1 a9 f0 03 00 Error: UNC at LBA = 0x03c1a9f0 = 63023600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 58 00 00 3b cb 56 88 40 00 09:09:46.401 READ FPDMA QUEUED 60 00 38 00 50 00 00 3b c7 d0 e8 40 00 09:09:46.401 READ FPDMA QUEUED 60 00 08 00 48 00 00 3b d8 ab 18 40 00 09:09:46.401 READ FPDMA QUEUED 60 00 08 00 40 00 00 03 c1 f8 78 40 00 09:09:46.401 READ FPDMA QUEUED 60 00 07 00 38 00 00 03 c1 f8 70 40 00 09:09:46.401 READ FPDMA QUEUED Error 619 [2] occurred at disk power-on lifetime: 35122 hours (1463 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 03 c1 a9 f0 03 00 Error: UNC at LBA = 0x03c1a9f0 = 63023600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 50 00 c0 00 00 3b d3 89 f8 40 00 09:09:42.571 READ FPDMA QUEUED 60 01 00 00 b8 00 00 03 c1 f6 b8 40 00 09:09:42.571 READ FPDMA QUEUED 60 00 08 00 b0 00 00 3b b9 94 c0 40 00 09:09:42.571 READ FPDMA QUEUED 60 00 08 00 a8 00 00 3b bd 09 f8 40 00 09:09:42.571 READ FPDMA QUEUED 60 01 00 00 a0 00 00 03 c1 f5 b8 40 00 09:09:42.570 READ FPDMA QUEUED Error 618 [1] occurred at disk power-on lifetime: 35122 hours (1463 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 03 c1 a9 f0 03 00 Error: UNC at LBA = 0x03c1a9f0 = 63023600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 30 00 00 03 c1 f8 50 40 00 09:09:38.673 READ FPDMA QUEUED 60 00 08 00 28 00 00 3b bd 0a c8 40 00 09:09:38.673 READ FPDMA QUEUED 60 00 08 00 20 00 00 3b cc fc 58 40 00 09:09:38.673 READ FPDMA QUEUED 60 00 01 00 18 00 00 03 c1 f8 48 40 00 09:09:38.673 READ FPDMA QUEUED 60 01 40 00 10 00 00 03 c1 f3 78 40 00 09:09:38.673 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8617 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 21/31 Celsius Lifetime Min/Max Temperature: 11/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (41) Index Estimated Time Temperature Celsius 42 2024-09-09 12:01 32 ************* 43 2024-09-09 12:02 31 ************ ... ..( 6 skipped). .. ************ 50 2024-09-09 12:09 31 ************ 51 2024-09-09 12:10 32 ************* 52 2024-09-09 12:11 32 ************* 53 2024-09-09 12:12 31 ************ ... ..( 27 skipped). .. ************ 81 2024-09-09 12:40 31 ************ 82 2024-09-09 12:41 ? - 83 2024-09-09 12:42 22 *** 84 2024-09-09 12:43 23 **** 85 2024-09-09 12:44 23 **** 86 2024-09-09 12:45 24 ***** 87 2024-09-09 12:46 24 ***** 88 2024-09-09 12:47 24 ***** 89 2024-09-09 12:48 25 ****** 90 2024-09-09 12:49 25 ****** 91 2024-09-09 12:50 26 ******* ... ..( 2 skipped). .. ******* 94 2024-09-09 12:53 26 ******* 95 2024-09-09 12:54 27 ******** ... ..( 2 skipped). .. ******** 98 2024-09-09 12:57 27 ******** 99 2024-09-09 12:58 28 ********* ... ..( 3 skipped). .. ********* 103 2024-09-09 13:02 28 ********* 104 2024-09-09 13:03 29 ********** ... ..( 6 skipped). .. ********** 111 2024-09-09 13:10 29 ********** 112 2024-09-09 13:11 30 *********** ... ..( 14 skipped). .. *********** 127 2024-09-09 13:26 30 *********** 0 2024-09-09 13:27 31 ************ ... ..( 40 skipped). .. ************ 41 2024-09-09 14:08 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 4946 --- Lifetime Power-On Resets 0x01 0x010 4 54130 --- Power-on Hours 0x01 0x018 6 161860145525 --- Logical Sectors Written 0x01 0x020 6 841019279 --- Number of Write Commands 0x01 0x028 6 104140055622 --- Logical Sectors Read 0x01 0x030 6 655845751 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 48609 --- Spindle Motor Power-on Hours 0x03 0x010 4 48608 --- Head Flying Hours 0x03 0x018 4 20901 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 669 --- Read Recovery Attempts 0x03 0x030 4 11 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 621 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 7 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x010 1 30 N-- Average Short Term Temperature 0x05 0x018 1 32 N-- Average Long Term Temperature 0x05 0x020 1 43 --- Highest Temperature 0x05 0x028 1 11 --- Lowest Temperature 0x05 0x030 1 40 N-- Highest Average Short Term Temperature 0x05 0x038 1 23 N-- Lowest Average Short Term Temperature 0x05 0x040 1 37 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 46446 --- Number of Hardware Resets 0x06 0x010 4 14788 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 16 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS