/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-16-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD5000LPSX-60A6WT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Jul 13 08:30:32 2022 +06 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 180) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 174) minutes. SCT capabilities: (0x303d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 32 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 3 Spin_Up_Time POS--K 052 051 021 - 1725 4 Start_Stop_Count -O--CK 100 100 000 - 412 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-K 100 100 030 - 29251 9 Power_On_Hours -O--CK 100 100 000 - 4391 10 Spin_Retry_Count PO--CK 100 100 050 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 403 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO-RCK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 191 G-Sense_Error_Rate -O--CK 001 001 000 - 763 192 Power-Off_Retract_Count -O--CK 100 100 000 - 356482285651 193 Load_Cycle_Count -O--CK 001 001 000 - 248728 194 Temperature_Celsius -O---K 033 051 000 - 33 (Min/Max 21/33) 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 240 Head_Flying_Hours -O--CK 100 100 000 - 202411 243 Unknown_Attribute -O--CK 100 100 000 - 688263 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 288 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 74 Device vendor specific log 0xb9 GPL,SL VS 4 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xc7 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 93 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 93 [20] occurred at disk power-on lifetime: 4390 hours (182 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 00:19:06.285 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 00:19:06.285 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 00:19:06.174 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:19:06.173 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 00:19:06.173 READ DMA EXT Error 92 [19] occurred at disk power-on lifetime: 4389 hours (182 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 00:41:39.003 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 00:41:39.002 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 00:41:20.138 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:41:20.137 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 00:41:20.137 READ DMA EXT Error 91 [18] occurred at disk power-on lifetime: 4389 hours (182 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 00:24:43.522 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 00:24:43.522 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 00:24:43.402 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:24:43.402 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 00:24:43.401 READ DMA EXT Error 90 [17] occurred at disk power-on lifetime: 4388 hours (182 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 00:01:09.389 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:09.389 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 00:01:09.268 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 00:01:09.268 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 00:01:09.268 READ DMA EXT Error 89 [16] occurred at disk power-on lifetime: 4387 hours (182 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 01:45:39.201 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 01:45:39.201 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 01:45:39.090 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 01:45:39.090 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 01:45:39.090 READ DMA EXT Error 88 [15] occurred at disk power-on lifetime: 4387 hours (182 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 01:45:07.383 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 01:45:07.383 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 01:45:03.134 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 01:45:03.134 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 01:45:03.134 READ DMA EXT Error 87 [14] occurred at disk power-on lifetime: 4387 hours (182 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 01:44:47.336 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 01:44:47.336 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 01:44:47.225 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 01:44:47.225 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 01:44:47.225 READ DMA EXT Error 86 [13] occurred at disk power-on lifetime: 4387 hours (182 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 00 00 00 e0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b4 00 20 00 00 00 00 00 72 4c 6b e0 00 01:39:12.565 SANITIZE DEVICE f5 00 00 00 00 00 00 00 00 00 00 e0 00 01:39:12.564 SECURITY FREEZE LOCK 25 00 00 00 20 00 00 3a 38 60 0f e0 00 01:39:12.453 READ DMA EXT 25 00 00 00 20 00 00 00 00 00 02 e0 00 01:39:12.453 READ DMA EXT 25 00 00 00 01 00 00 3a 38 60 2e e0 00 01:39:12.452 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 21/33 Celsius Lifetime Min/Max Temperature: 17/51 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (11) Index Estimated Time Temperature Celsius 12 2022-07-13 06:23 41 ********************** ... ..( 2 skipped). .. ********************** 15 2022-07-13 06:26 41 ********************** 16 2022-07-13 06:27 40 ********************* ... ..( 3 skipped). .. ********************* 20 2022-07-13 06:31 40 ********************* 21 2022-07-13 06:32 ? - 22 2022-07-13 06:33 40 ********************* 23 2022-07-13 06:34 ? - 24 2022-07-13 06:35 29 ********** 25 2022-07-13 06:36 ? - 26 2022-07-13 06:37 29 ********** 27 2022-07-13 06:38 30 *********** 28 2022-07-13 06:39 30 *********** 29 2022-07-13 06:40 30 *********** 30 2022-07-13 06:41 31 ************ 31 2022-07-13 06:42 31 ************ 32 2022-07-13 06:43 32 ************* 33 2022-07-13 06:44 33 ************** 34 2022-07-13 06:45 33 ************** 35 2022-07-13 06:46 34 *************** 36 2022-07-13 06:47 34 *************** 37 2022-07-13 06:48 35 **************** 38 2022-07-13 06:49 35 **************** 39 2022-07-13 06:50 36 ***************** 40 2022-07-13 06:51 36 ***************** 41 2022-07-13 06:52 37 ****************** 42 2022-07-13 06:53 37 ****************** 43 2022-07-13 06:54 37 ****************** 44 2022-07-13 06:55 38 ******************* ... ..( 2 skipped). .. ******************* 47 2022-07-13 06:58 38 ******************* 48 2022-07-13 06:59 39 ******************** ... ..( 3 skipped). .. ******************** 52 2022-07-13 07:03 39 ******************** 53 2022-07-13 07:04 40 ********************* ... ..( 5 skipped). .. ********************* 59 2022-07-13 07:10 40 ********************* 60 2022-07-13 07:11 41 ********************** ... ..( 6 skipped). .. ********************** 67 2022-07-13 07:18 41 ********************** 68 2022-07-13 07:19 42 *********************** ... ..( 2 skipped). .. *********************** 71 2022-07-13 07:22 42 *********************** 72 2022-07-13 07:23 ? - 73 2022-07-13 07:24 42 *********************** 74 2022-07-13 07:25 ? - 75 2022-07-13 07:26 42 *********************** 76 2022-07-13 07:27 ? - 77 2022-07-13 07:28 42 *********************** 78 2022-07-13 07:29 42 *********************** 79 2022-07-13 07:30 42 *********************** 80 2022-07-13 07:31 43 ************************ 81 2022-07-13 07:32 ? - 82 2022-07-13 07:33 42 *********************** 83 2022-07-13 07:34 ? - 84 2022-07-13 07:35 41 ********************** 85 2022-07-13 07:36 41 ********************** 86 2022-07-13 07:37 41 ********************** 87 2022-07-13 07:38 42 *********************** 88 2022-07-13 07:39 41 ********************** ... ..( 5 skipped). .. ********************** 94 2022-07-13 07:45 41 ********************** 95 2022-07-13 07:46 42 *********************** ... ..( 2 skipped). .. *********************** 98 2022-07-13 07:49 42 *********************** 99 2022-07-13 07:50 41 ********************** 100 2022-07-13 07:51 41 ********************** 101 2022-07-13 07:52 41 ********************** 102 2022-07-13 07:53 40 ********************* 103 2022-07-13 07:54 41 ********************** 104 2022-07-13 07:55 41 ********************** 105 2022-07-13 07:56 41 ********************** 106 2022-07-13 07:57 42 *********************** 107 2022-07-13 07:58 ? - 108 2022-07-13 07:59 21 ** 109 2022-07-13 08:00 22 *** 110 2022-07-13 08:01 23 **** 111 2022-07-13 08:02 25 ****** 112 2022-07-13 08:03 25 ****** 113 2022-07-13 08:04 26 ******* 114 2022-07-13 08:05 27 ******** 115 2022-07-13 08:06 28 ********* 116 2022-07-13 08:07 28 ********* 117 2022-07-13 08:08 29 ********** 118 2022-07-13 08:09 29 ********** 119 2022-07-13 08:10 30 *********** ... ..( 11 skipped). .. *********** 3 2022-07-13 08:22 30 *********** 4 2022-07-13 08:23 31 ************ 5 2022-07-13 08:24 31 ************ 6 2022-07-13 08:25 32 ************* ... ..( 3 skipped). .. ************* 10 2022-07-13 08:29 32 ************* 11 2022-07-13 08:30 33 ************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 3 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1910 Vendor specific