/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-60-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS240G1G0B-00RC30 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: Z3311000 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: M.2 TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Feb 19 14:04:43 2023 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 000 100 000 - 12456 12 Power_Cycle_Count -O--CK 100 100 000 - 1486 165 Block_Erase_Count -O--CK 100 100 000 - 6421119043634 166 Minimum_PE_Cycles_TLC -O--CK 100 100 000 - 6 167 Max_Bad_Blocks_per_Die -O--CK 100 100 000 - 0 168 Maximum_PE_Cycles_TLC -O--CK 100 100 000 - 50 169 Total_Bad_Blocks -O--CK 100 100 000 - 0 170 Grown_Bad_Blocks -O--CK 100 100 000 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 000 - 27 174 Unexpected_Power_Loss -O--CK 100 100 000 - 239 187 Reported_Uncorrect -O--CK 100 100 000 - 288 188 Command_Timeout -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 070 043 000 - 30 (Min/Max 0/57) 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 230 Media_Wearout_Indicator -O--CK 100 100 000 - 0x02bb018902bb 232 Available_Reservd_Space PO--CK 100 100 004 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 000 - 6600 234 NAND_GB_Written_SLC -O--CK 100 100 000 - 19641 241 Host_Writes_GiB ----CK 253 253 000 - 10269 242 Host_Reads_GiB ----CK 253 253 000 - 13171 244 Temp_Throttle_Status -O--CK 000 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] log entry is empty SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1486 --- Lifetime Power-On Resets 0x01 0x010 4 12456 --- Power-on Hours 0x01 0x018 6 62080403 --- Logical Sectors Written 0x01 0x020 6 508872374 --- Number of Write Commands 0x01 0x028 6 1853733265 --- Logical Sectors Read 0x01 0x030 6 541636478 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 6 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-60-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.D Device Model: Hitachi HDS721050DLE630 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MS1OA610 User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Feb 19 14:04:43 2023 IST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4574) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 77) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 138 138 054 - 85 3 Spin_Up_Time POS--- 120 120 024 - 194 (Average 189) 4 Start_Stop_Count -O--C- 097 097 000 - 15145 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 61 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 115 115 020 - 34 9 Power_On_Hours -O--C- 092 092 000 - 62457 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3641 192 Power-Off_Retract_Count -O--CK 088 088 000 - 15513 193 Load_Cycle_Count -O--C- 088 088 000 - 15513 194 Temperature_Celsius -O---- 222 222 000 - 27 (Min/Max 15/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 106 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 203 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 207 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 207 [2] occurred at disk power-on lifetime: 62415 hours (2600 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 08 00 00 02 02 49 e8 02 00 Error: ICRC, ABRT at LBA = 0x020249e8 = 33704424 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 20 00 00 02 02 4a 18 40 00 00:01:34.425 WRITE FPDMA QUEUED 61 00 10 00 18 00 00 02 02 4a 00 40 00 00:01:34.425 WRITE FPDMA QUEUED 61 00 18 00 10 00 00 02 02 49 d8 40 00 00:01:34.425 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 02 02 49 c8 40 00 00:01:34.425 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 02 02 49 b8 40 00 00:01:34.425 WRITE FPDMA QUEUED Error 206 [1] occurred at disk power-on lifetime: 62415 hours (2600 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 0c 00 1b 07 0c 00 Error: ICRC, ABRT at LBA = 0x0c001b07 = 201333511 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 48 00 00 0c 00 1b 28 40 00 00:01:33.601 WRITE FPDMA QUEUED 61 00 10 00 40 00 00 0c 00 1b 10 40 00 00:01:33.601 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 0c 00 1b 00 40 00 00:01:33.601 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 0c 00 15 b8 40 00 00:01:33.601 WRITE FPDMA QUEUED 61 00 08 00 28 00 00 0c 00 0c e8 40 00 00:01:33.601 WRITE FPDMA QUEUED Error 205 [0] occurred at disk power-on lifetime: 62415 hours (2600 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 07 e8 00 00 03 5c d9 c0 03 00 Error: ICRC, ABRT at LBA = 0x035cd9c0 = 56416704 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 09 a8 00 00 00 00 03 5c d8 00 40 00 00:01:28.644 WRITE FPDMA QUEUED 60 00 08 00 68 00 00 0f 44 16 b0 40 00 00:01:28.633 READ FPDMA QUEUED 60 00 08 00 60 00 00 0f 44 16 a8 40 00 00:01:28.633 READ FPDMA QUEUED 60 00 08 00 58 00 00 0f 44 16 a0 40 00 00:01:28.633 READ FPDMA QUEUED 60 00 08 00 50 00 00 17 04 39 48 40 00 00:01:28.632 READ FPDMA QUEUED Error 204 [3] occurred at disk power-on lifetime: 62415 hours (2600 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 b0 00 00 10 04 13 20 00 00 Error: ICRC, ABRT at LBA = 0x10041320 = 268702496 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 b0 00 b0 00 00 10 04 12 20 40 00 00:01:20.480 WRITE FPDMA QUEUED 60 00 08 00 a8 00 00 12 01 0c 30 40 00 00:01:20.480 READ FPDMA QUEUED 60 00 08 00 50 00 00 1e 20 29 f0 40 00 00:01:20.461 READ FPDMA QUEUED 60 00 40 00 48 00 00 1e 20 08 20 40 00 00:01:20.461 READ FPDMA QUEUED 60 00 20 00 80 00 00 0e 08 1c d0 40 00 00:01:20.449 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 50880 - # 2 Short offline Completed without error 00% 44123 - # 3 Short offline Completed without error 00% 44123 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 26/28 Celsius Lifetime Min/Max Temperature: 15/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (37) Index Estimated Time Temperature Celsius 38 2023-02-19 11:57 28 ********* 39 2023-02-19 11:58 27 ******** 40 2023-02-19 11:59 28 ********* ... ..( 21 skipped). .. ********* 62 2023-02-19 12:21 28 ********* 63 2023-02-19 12:22 ? - 64 2023-02-19 12:23 18 - 65 2023-02-19 12:24 18 - 66 2023-02-19 12:25 19 - 67 2023-02-19 12:26 20 * 68 2023-02-19 12:27 20 * 69 2023-02-19 12:28 21 ** 70 2023-02-19 12:29 21 ** 71 2023-02-19 12:30 22 *** 72 2023-02-19 12:31 22 *** 73 2023-02-19 12:32 23 **** 74 2023-02-19 12:33 23 **** 75 2023-02-19 12:34 24 ***** ... ..( 4 skipped). .. ***** 80 2023-02-19 12:39 24 ***** 81 2023-02-19 12:40 25 ****** ... ..( 5 skipped). .. ****** 87 2023-02-19 12:46 25 ****** 88 2023-02-19 12:47 26 ******* 89 2023-02-19 12:48 26 ******* 90 2023-02-19 12:49 26 ******* 91 2023-02-19 12:50 ? - 92 2023-02-19 12:51 ? - 93 2023-02-19 12:52 ? - 94 2023-02-19 12:53 26 ******* 95 2023-02-19 12:54 27 ******** ... ..( 23 skipped). .. ******** 119 2023-02-19 13:18 27 ******** 120 2023-02-19 13:19 28 ********* ... ..( 2 skipped). .. ********* 123 2023-02-19 13:22 28 ********* 124 2023-02-19 13:23 27 ******** 125 2023-02-19 13:24 28 ********* 126 2023-02-19 13:25 27 ******** 127 2023-02-19 13:26 27 ******** 0 2023-02-19 13:27 28 ********* 1 2023-02-19 13:28 27 ******** 2 2023-02-19 13:29 28 ********* 3 2023-02-19 13:30 28 ********* 4 2023-02-19 13:31 27 ******** 5 2023-02-19 13:32 27 ******** 6 2023-02-19 13:33 28 ********* 7 2023-02-19 13:34 27 ******** 8 2023-02-19 13:35 28 ********* 9 2023-02-19 13:36 27 ******** 10 2023-02-19 13:37 27 ******** 11 2023-02-19 13:38 28 ********* ... ..( 2 skipped). .. ********* 14 2023-02-19 13:41 28 ********* 15 2023-02-19 13:42 27 ******** ... ..( 3 skipped). .. ******** 19 2023-02-19 13:46 27 ******** 20 2023-02-19 13:47 28 ********* 21 2023-02-19 13:48 27 ******** 22 2023-02-19 13:49 27 ******** 23 2023-02-19 13:50 27 ******** 24 2023-02-19 13:51 28 ********* 25 2023-02-19 13:52 27 ******** ... ..( 11 skipped). .. ******** 37 2023-02-19 14:04 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 3641 --- Lifetime Power-On Resets 0x01 0x010 4 62457 --- Power-on Hours 0x01 0x018 6 42692004195 --- Logical Sectors Written 0x01 0x020 6 926553475 --- Number of Write Commands 0x01 0x028 6 1057235153015 --- Logical Sectors Read 0x01 0x030 6 5618380750 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 55248 --- Spindle Motor Power-on Hours 0x03 0x010 4 55247 --- Head Flying Hours 0x03 0x018 4 15513 --- Head Load Events 0x03 0x020 4 61 --- Number of Reallocated Logical Sectors 0x03 0x028 4 6 --- Read Recovery Attempts 0x03 0x030 4 9 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2007 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x010 1 27 N-- Average Short Term Temperature 0x05 0x018 1 26 N-- Average Long Term Temperature 0x05 0x020 1 49 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 45 N-- Highest Average Short Term Temperature 0x05 0x038 1 22 N-- Lowest Average Short Term Temperature 0x05 0x040 1 42 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 25086 --- Number of Hardware Resets 0x06 0x010 4 5999 --- Number of ASR Events 0x06 0x018 4 203 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS