/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Serial ATA Device Model: WDC WD600BEAS-22KZT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.06M01 User Capacity: 60 011 642 880 bytes [60,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon Mar 13 13:31:12 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 2880) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 22 3 Spin_Up_Time PO---- 160 159 021 - 975 4 Start_Stop_Count -O--CK 097 097 000 - 3789 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 091 091 000 - 7201 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3456 192 Power-Off_Retract_Count -O--CK 196 196 000 - 3393 193 Load_Cycle_Count -O--CK 121 121 000 - 238343 194 Temperature_Celsius -O---K 103 081 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 21 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 21 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 00 01 2d 00 41 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 da 25 00 56 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 2d ff 00 9f 00 ec 01 4b 29 00 00 00 00:00:40.749 NOP [Reserved subcommand] [OBS-ACS-2] 01 9c 25 00 41 00 2d 00 9f ff 00 00 01 00:00:16.796 [RESERVED] 00 2e ff 00 5f 00 9b 01 41 25 00 00 00 00:00:36.114 NOP [Reserved subcommand] [OBS-ACS-2] Error 20 [19] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 2d 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ec 29 00 4b 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 2d ff 00 9f 00 9c 01 41 25 00 00 00 00:00:40.749 NOP [Reserved subcommand] [OBS-ACS-2] 01 9b 25 00 41 00 12 00 8d ff 00 00 01 00:00:16.796 [RESERVED] 00 11 ff 00 4e 00 9b 01 41 25 00 00 00 00:00:24.366 NOP [Reserved subcommand] [OBS-ACS-2] Error 19 [18] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 2d 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9c 25 00 41 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 12 ff 00 8d 00 9c 01 41 25 00 00 00 00:00:40.749 NOP [Reserved subcommand] [OBS-ACS-2] 01 9b 25 00 41 00 2e 00 5f ff 00 00 01 00:00:16.795 [RESERVED] 00 2f ff 00 1f 00 9a 01 41 25 00 00 00 00:00:19.985 NOP [Reserved subcommand] [OBS-ACS-2] Error 18 [17] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 3b 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5c 29 00 ae 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ff 00 d7 00 e3 01 a3 25 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] 01 f0 25 00 8e 00 3b 00 d7 ff 00 00 01 00:00:39.276 [RESERVED] 00 3b ff 00 d7 00 d8 01 82 29 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] Error 17 [16] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 3b 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e3 25 00 a3 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ff 00 d7 00 6c 01 99 29 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] 01 d8 29 00 82 00 3b 00 d7 ff 00 00 01 00:00:36.592 [RESERVED] 00 3b ff 00 d7 00 8a 01 78 25 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] Error 16 [15] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 3b 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 6c 29 00 99 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ff 00 d7 00 f0 01 8e 25 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] 01 8a 25 00 78 00 3b 00 d7 ff 00 00 01 00:00:33.496 [RESERVED] 00 04 ff 00 d3 00 89 01 78 25 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] Error 15 [14] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 3b 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f0 25 00 8e 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ff 00 d7 00 d8 01 82 29 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] 01 89 25 00 78 00 3b 00 d7 ff 00 00 01 00:00:30.858 [RESERVED] 00 0c ff 00 c7 00 88 01 78 25 00 00 00 00:00:54.020 NOP [Reserved subcommand] [OBS-ACS-2] Error 14 [13] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 00 01 3b 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d8 29 00 82 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ff 00 d7 00 8a 01 78 25 00 00 00 00:00:55.099 NOP [Reserved subcommand] [OBS-ACS-2] 01 88 25 00 78 00 04 00 d3 ff 00 00 01 00:00:30.857 [RESERVED] 00 33 ff 00 94 00 88 01 78 25 00 00 00 00:00:50.956 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 40 Celsius Power Cycle Max Temperature: 40 Celsius Lifetime Max Temperature: 62 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/65 Celsius Min/Max Temperature Limit: 1/70 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2017-03-13 11:24 40 ********************* ... ..( 25 skipped). .. ********************* 73 2017-03-13 11:50 40 ********************* 74 2017-03-13 11:51 41 ********************** 75 2017-03-13 11:52 40 ********************* 76 2017-03-13 11:53 41 ********************** ... ..( 2 skipped). .. ********************** 79 2017-03-13 11:56 41 ********************** 80 2017-03-13 11:57 40 ********************* ... ..( 2 skipped). .. ********************* 83 2017-03-13 12:00 40 ********************* 84 2017-03-13 12:01 42 *********************** ... ..( 3 skipped). .. *********************** 88 2017-03-13 12:05 42 *********************** 89 2017-03-13 12:06 41 ********************** ... ..( 4 skipped). .. ********************** 94 2017-03-13 12:11 41 ********************** 95 2017-03-13 12:12 40 ********************* ... ..( 3 skipped). .. ********************* 99 2017-03-13 12:16 40 ********************* 100 2017-03-13 12:17 41 ********************** 101 2017-03-13 12:18 41 ********************** 102 2017-03-13 12:19 40 ********************* 103 2017-03-13 12:20 41 ********************** ... ..( 12 skipped). .. ********************** 116 2017-03-13 12:33 41 ********************** 117 2017-03-13 12:34 40 ********************* 118 2017-03-13 12:35 41 ********************** 119 2017-03-13 12:36 41 ********************** 120 2017-03-13 12:37 41 ********************** 121 2017-03-13 12:38 40 ********************* ... ..( 32 skipped). .. ********************* 26 2017-03-13 13:11 40 ********************* 27 2017-03-13 13:12 ? - 28 2017-03-13 13:13 41 ********************** 29 2017-03-13 13:14 41 ********************** 30 2017-03-13 13:15 ? - 31 2017-03-13 13:16 42 *********************** 32 2017-03-13 13:17 42 *********************** 33 2017-03-13 13:18 ? - 34 2017-03-13 13:19 43 ************************ 35 2017-03-13 13:20 43 ************************ 36 2017-03-13 13:21 ? - 37 2017-03-13 13:22 44 ************************* 38 2017-03-13 13:23 44 ************************* 39 2017-03-13 13:24 ? - 40 2017-03-13 13:25 40 ********************* ... ..( 5 skipped). .. ********************* 46 2017-03-13 13:31 40 ********************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x8000 4 413 Vendor specific