/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD1600BEVS-22RST0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 04.01G04 User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Mon Jun 13 05:15:34 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7200) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 92) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 29 3 Spin_Up_Time PO---- 192 185 021 - 1391 4 Start_Stop_Count -O--CK 095 095 000 - 5178 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate POSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 048 048 000 - 38116 10 Spin_Retry_Count PO--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 5044 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1732 193 Load_Cycle_Count -O--CK 119 119 000 - 245144 194 Temperature_Celsius -O---K 113 084 000 - 34 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 100 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 11 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 11 [10] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 7e 25 1b 65 00 00 00 00 00 01 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 2f 1b 60 08 65 25 00 01 00 00:01:01.184 NOP [Abort queued commands] 0a fd 25 1b 64 00 00 00 ef 00 01 00 0a 05:09:32.564 [RESERVED] 00 00 00 00 67 1b 51 0c 64 25 00 01 00 00:01:01.184 NOP [Abort queued commands] Error 10 [9] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 2a 25 c2 69 00 00 00 00 00 00 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 9f c2 1e 00 69 25 00 00 00 00:01:01.184 NOP [Abort queued commands] 00 d3 25 c2 68 00 08 00 1f 00 00 00 0a 03:32:20.822 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 ef c2 d2 0a 68 25 00 00 00 00:01:01.184 NOP [Abort queued commands] Error 9 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 4b 25 6a 33 00 00 00 00 00 00 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 f7 6a 49 06 33 25 00 00 00 00:00:28.544 NOP [Abort queued commands] 00 49 25 6a 33 00 08 00 cf 00 00 00 06 01:55:59.945 NOP [Reserved subcommand] [OBS-ACS-2] 00 16 00 00 b9 6a 49 00 33 25 00 00 00 00:00:12.040 NOP [Abort queued commands] Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b9 25 6a 26 00 00 00 00 00 00 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 00 00 4f 6a b9 01 26 35 00 00 00 00:01:01.184 NOP [Abort queued commands] 0a 97 25 6a 26 00 00 00 ef 00 00 00 0a 01:55:56.715 [RESERVED] 00 00 00 00 77 6a 6e 0b 26 25 00 00 00 00:01:01.184 NOP [Abort queued commands] Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9c 25 21 ae 00 00 00 00 00 00 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 e7 21 9c 00 ae 25 00 00 00 00:00:28.544 NOP [Abort queued commands] 00 92 25 21 ae 00 40 00 89 00 00 00 00 00:36:47.388 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 e2 21 86 00 ae 25 00 00 00 00:00:36.896 NOP [Abort queued commands] Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 19 25 21 a3 00 00 00 00 00 00 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 00 00 0f 21 15 06 a3 25 00 00 00 00:01:01.184 NOP [Abort queued commands] 06 08 25 21 a3 00 80 00 3f 00 00 00 00 00:36:44.424 DATA SET MANAGEMENT 00 40 00 00 37 21 fc 00 a2 25 00 00 00 00:00:55.048 NOP [Abort queued commands] Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 94 25 13 5d 00 00 00 00 00 01 00 0a 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 00 00 ef 13 91 0a 5d 25 00 01 00 00:01:01.184 NOP [Abort queued commands] 0a 6d 25 13 5d 00 00 00 ef 00 01 00 06 05:00:46.337 [RESERVED] 00 00 00 00 ef 13 68 0a 5d 25 00 01 00 00:00:44.808 NOP [Abort queued commands] Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 fe 25 00 e6 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 0f 00 d3 00 db 25 00 00 00 00:00:03.848 NOP [Abort queued commands] 00 d3 25 00 db 00 08 00 07 00 00 00 00 00:00:56.275 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 00 00 f7 00 d2 00 db 25 00 00 00 00:01:05.288 NOP [Abort queued commands] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Max Temperature: 38 Celsius Lifetime Max Temperature: 0 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/65 Celsius Min/Max Temperature Limit: 1/70 Celsius Temperature History Size (Index): 128 (109) Index Estimated Time Temperature Celsius 110 2016-06-13 03:08 22 *** 111 2016-06-13 03:09 ? - 112 2016-06-13 03:10 42 *********************** 113 2016-06-13 03:11 ? - 114 2016-06-13 03:12 42 *********************** 115 2016-06-13 03:13 ? - 116 2016-06-13 03:14 22 *** 117 2016-06-13 03:15 ? - 118 2016-06-13 03:16 24 ***** 119 2016-06-13 03:17 ? - 120 2016-06-13 03:18 24 ***** 121 2016-06-13 03:19 ? - 122 2016-06-13 03:20 26 ******* 123 2016-06-13 03:21 ? - 124 2016-06-13 03:22 26 ******* 125 2016-06-13 03:23 ? - 126 2016-06-13 03:24 26 ******* 127 2016-06-13 03:25 ? - 0 2016-06-13 03:26 26 ******* 1 2016-06-13 03:27 ? - 2 2016-06-13 03:28 27 ******** 3 2016-06-13 03:29 ? - 4 2016-06-13 03:30 28 ********* 5 2016-06-13 03:31 ? - 6 2016-06-13 03:32 28 ********* 7 2016-06-13 03:33 ? - 8 2016-06-13 03:34 20 * 9 2016-06-13 03:35 ? - 10 2016-06-13 03:36 24 ***** 11 2016-06-13 03:37 ? - 12 2016-06-13 03:38 22 *** 13 2016-06-13 03:39 ? - 14 2016-06-13 03:40 29 ********** 15 2016-06-13 03:41 ? - 16 2016-06-13 03:42 14 - 17 2016-06-13 03:43 ? - 18 2016-06-13 03:44 42 *********************** 19 2016-06-13 03:45 ? - 20 2016-06-13 03:46 44 ************************* 21 2016-06-13 03:47 ? - 22 2016-06-13 03:48 22 *** 23 2016-06-13 03:49 ? - 24 2016-06-13 03:50 22 *** 25 2016-06-13 03:51 ? - 26 2016-06-13 03:52 22 *** 27 2016-06-13 03:53 ? - 28 2016-06-13 03:54 22 *** 29 2016-06-13 03:55 ? - 30 2016-06-13 03:56 24 ***** 31 2016-06-13 03:57 ? - 32 2016-06-13 03:58 22 *** 33 2016-06-13 03:59 ? - 34 2016-06-13 04:00 24 ***** 35 2016-06-13 04:01 ? - 36 2016-06-13 04:02 20 * 37 2016-06-13 04:03 ? - 38 2016-06-13 04:04 24 ***** 39 2016-06-13 04:05 ? - 40 2016-06-13 04:06 44 ************************* 41 2016-06-13 04:07 ? - 42 2016-06-13 04:08 24 ***** 43 2016-06-13 04:09 ? - 44 2016-06-13 04:10 40 ********************* 45 2016-06-13 04:11 ? - 46 2016-06-13 04:12 22 *** 47 2016-06-13 04:13 ? - 48 2016-06-13 04:14 22 *** 49 2016-06-13 04:15 ? - 50 2016-06-13 04:16 24 ***** 51 2016-06-13 04:17 ? - 52 2016-06-13 04:18 23 **** 53 2016-06-13 04:19 ? - 54 2016-06-13 04:20 24 ***** 55 2016-06-13 04:21 ? - 56 2016-06-13 04:22 24 ***** 57 2016-06-13 04:23 ? - 58 2016-06-13 04:24 26 ******* 59 2016-06-13 04:25 ? - 60 2016-06-13 04:26 ? - 61 2016-06-13 04:27 34 *************** 62 2016-06-13 04:28 ? - 63 2016-06-13 04:29 36 ***************** 64 2016-06-13 04:30 ? - 65 2016-06-13 04:31 34 *************** 66 2016-06-13 04:32 ? - 67 2016-06-13 04:33 24 ***** 68 2016-06-13 04:34 ? - 69 2016-06-13 04:35 22 *** 70 2016-06-13 04:36 ? - 71 2016-06-13 04:37 24 ***** 72 2016-06-13 04:38 ? - 73 2016-06-13 04:39 24 ***** 74 2016-06-13 04:40 ? - 75 2016-06-13 04:41 24 ***** 76 2016-06-13 04:42 ? - 77 2016-06-13 04:43 24 ***** 78 2016-06-13 04:44 ? - 79 2016-06-13 04:45 24 ***** 80 2016-06-13 04:46 ? - 81 2016-06-13 04:47 26 ******* 82 2016-06-13 04:48 ? - 83 2016-06-13 04:49 26 ******* 84 2016-06-13 04:50 ? - 85 2016-06-13 04:51 38 ******************* 86 2016-06-13 04:52 ? - 87 2016-06-13 04:53 24 ***** 88 2016-06-13 04:54 ? - 89 2016-06-13 04:55 25 ****** 90 2016-06-13 04:56 ? - 91 2016-06-13 04:57 42 *********************** 92 2016-06-13 04:58 ? - 93 2016-06-13 04:59 22 *** 94 2016-06-13 05:00 ? - 95 2016-06-13 05:01 24 ***** 96 2016-06-13 05:02 ? - 97 2016-06-13 05:03 26 ******* 98 2016-06-13 05:04 ? - 99 2016-06-13 05:05 20 * 100 2016-06-13 05:06 ? - 101 2016-06-13 05:07 ? - 102 2016-06-13 05:08 20 * 103 2016-06-13 05:09 ? - 104 2016-06-13 05:10 18 - 105 2016-06-13 05:11 ? - 106 2016-06-13 05:12 ? - 107 2016-06-13 05:13 38 ******************* 108 2016-06-13 05:14 ? - 109 2016-06-13 05:15 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x8000 4 16321 Vendor specific