/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 860 EVO 250GB Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: RVT04B6Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Mar 12 16:05:36 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 097 097 000 - 12041 12 Power_Cycle_Count -O--CK 097 097 000 - 2892 177 Wear_Leveling_Count PO--C- 096 096 000 - 71 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 071 042 000 - 29 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 887 235 POR_Recovery_Count -O--C- 099 099 000 - 1426 241 Total_LBAs_Written -O--CK 099 099 000 - 24614729432 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 SL VS 16 Device vendor specific log 0xa5 SL VS 16 Device vendor specific log 0xce SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10949 - # 2 Extended offline Interrupted (host reset) 80% 10947 - # 3 Extended offline Interrupted (host reset) 60% 10783 - # 4 Extended offline Interrupted (host reset) 80% 10782 - # 5 Short offline Completed without error 00% 3283 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 27/40 Celsius Lifetime Min/Max Temperature: 17/58 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 SMART Status: 0xc24f (PASSED) SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 10 minutes Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (79) Index Estimated Time Temperature Celsius 80 2022-03-11 18:50 26 ******* ... ..( 7 skipped). .. ******* 88 2022-03-11 20:10 26 ******* 89 2022-03-11 20:20 27 ******** 90 2022-03-11 20:30 26 ******* 91 2022-03-11 20:40 27 ******** 92 2022-03-11 20:50 26 ******* 93 2022-03-11 21:00 27 ******** 94 2022-03-11 21:10 26 ******* ... ..( 5 skipped). .. ******* 100 2022-03-11 22:10 26 ******* 101 2022-03-11 22:20 27 ******** 102 2022-03-11 22:30 27 ******** 103 2022-03-11 22:40 26 ******* 104 2022-03-11 22:50 26 ******* 105 2022-03-11 23:00 27 ******** 106 2022-03-11 23:10 27 ******** 107 2022-03-11 23:20 27 ******** 108 2022-03-11 23:30 26 ******* 109 2022-03-11 23:40 26 ******* 110 2022-03-11 23:50 26 ******* 111 2022-03-12 00:00 27 ******** 112 2022-03-12 00:10 28 ********* 113 2022-03-12 00:20 27 ******** 114 2022-03-12 00:30 ? - 115 2022-03-12 00:40 28 ********* ... ..( 2 skipped). .. ********* 118 2022-03-12 01:10 28 ********* 119 2022-03-12 01:20 29 ********** ... ..( 6 skipped). .. ********** 126 2022-03-12 02:30 29 ********** 127 2022-03-12 02:40 28 ********* ... ..( 2 skipped). .. ********* 2 2022-03-12 03:10 28 ********* 3 2022-03-12 03:20 29 ********** ... ..( 17 skipped). .. ********** 21 2022-03-12 06:20 29 ********** 22 2022-03-12 06:30 28 ********* 23 2022-03-12 06:40 27 ******** 24 2022-03-12 06:50 27 ******** 25 2022-03-12 07:00 28 ********* 26 2022-03-12 07:10 29 ********** 27 2022-03-12 07:20 29 ********** 28 2022-03-12 07:30 30 *********** 29 2022-03-12 07:40 30 *********** 30 2022-03-12 07:50 30 *********** 31 2022-03-12 08:00 29 ********** ... ..( 11 skipped). .. ********** 43 2022-03-12 10:00 29 ********** 44 2022-03-12 10:10 28 ********* 45 2022-03-12 10:20 28 ********* 46 2022-03-12 10:30 29 ********** ... ..( 3 skipped). .. ********** 50 2022-03-12 11:10 29 ********** 51 2022-03-12 11:20 30 *********** 52 2022-03-12 11:30 30 *********** 53 2022-03-12 11:40 29 ********** 54 2022-03-12 11:50 29 ********** 55 2022-03-12 12:00 29 ********** 56 2022-03-12 12:10 30 *********** 57 2022-03-12 12:20 30 *********** 58 2022-03-12 12:30 29 ********** ... ..( 9 skipped). .. ********** 68 2022-03-12 14:10 29 ********** 69 2022-03-12 14:20 28 ********* 70 2022-03-12 14:30 29 ********** 71 2022-03-12 14:40 29 ********** 72 2022-03-12 14:50 28 ********* 73 2022-03-12 15:00 28 ********* 74 2022-03-12 15:10 29 ********** ... ..( 4 skipped). .. ********** 79 2022-03-12 16:00 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2892 --- Lifetime Power-On Resets 0x01 0x010 4 12041 --- Power-on Hours 0x01 0x018 6 24614729432 --- Logical Sectors Written 0x01 0x020 6 339457842 --- Number of Write Commands 0x01 0x028 6 26869686709 --- Logical Sectors Read 0x01 0x030 6 392451502 --- Number of Read Commands 0x01 0x038 6 1507000 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 1057 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 29 --- Current Temperature 0x05 0x020 1 58 --- Highest Temperature 0x05 0x028 1 17 --- Lowest Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 13974 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 887 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7 Device Model: SAMSUNG HM500JI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AC101C4 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Mar 12 16:05:36 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x05) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8100) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 135) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 713 2 Throughput_Performance -OS--K 055 055 000 - 7430 3 Spin_Up_Time PO---K 091 073 025 - 2830 4 Start_Stop_Count -O--CK 087 087 000 - 13976 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 28 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 21897 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 001 001 000 - 398585 12 Power_Cycle_Count -O--CK 094 094 000 - 6142 191 G-Sense_Error_Rate -O---K 089 089 000 - 119431 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 039 000 - 30 (Min/Max 6/63) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 100 100 000 - 28 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 2 200 Multi_Zone_Error_Rate -O-R-K 001 001 000 - 74444 223 Load_Retry_Count -O--CK 001 001 000 - 398585 225 Load_Cycle_Count -O--CK 001 001 000 - 27694094 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xbb GPL VS 4 Device vendor specific log 0xbc GPL VS 2 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 399 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 399 [6] occurred at disk power-on lifetime: 18565 hours (773 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 5a 7c ef 3d 40 00 Error: IDNF 1 sectors at LBA = 0x5a7cef3d = 1518137149 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d1 00 01 00 00 5a 7c ef 3d 40 00 00:04:02.461 READ DMA EXT 25 00 d1 00 01 00 00 00 00 00 00 40 00 00:04:02.461 READ DMA EXT b0 00 d1 00 01 00 00 00 c2 4f 01 00 00 00:04:02.230 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 00 d0 00 01 00 00 00 c2 4f 01 00 00 00:04:02.229 SMART READ DATA ec 00 00 00 01 00 00 00 00 00 00 00 00 00:04:02.228 IDENTIFY DEVICE Error 398 [5] occurred at disk power-on lifetime: 16437 hours (684 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 53 10 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 01 00 00 00 03 89 53 10 40 00 00:00:01.032 READ FPDMA QUEUED 60 00 10 01 00 00 00 03 89 52 10 40 00 00:00:01.032 READ FPDMA QUEUED 60 00 c1 01 00 00 00 03 89 51 10 40 00 00:00:01.032 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 89 50 10 40 00 00:00:01.032 READ FPDMA QUEUED 60 00 10 01 00 00 00 03 89 4f 10 40 00 00:00:01.032 READ FPDMA QUEUED Error 397 [4] occurred at disk power-on lifetime: 16437 hours (684 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 01 21 10 00 00 00 00 00 00 40 00 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 03 1b 21 10 40 00 00:00:00.973 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 1b 20 10 40 00 00:00:00.973 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 1b 1f 10 40 00 00:00:00.973 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 1b 1e 10 40 00 00:00:00.973 READ FPDMA QUEUED 60 00 00 01 00 00 00 03 1b 1d 10 40 00 00:00:00.973 READ FPDMA QUEUED Error 396 [3] occurred at disk power-on lifetime: 14443 hours (601 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 04 00 00 1e 4c fd 2c e0 00 Error: UNC 4 sectors at LBA = 0x1e4cfd2c = 508362028 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 1e 4c fd 28 e0 00 00:00:37.183 READ DMA EXT 25 00 00 00 10 00 00 1e 28 82 c8 e0 00 00:00:37.183 READ DMA EXT 25 00 00 00 40 00 00 1e 28 31 b0 e0 00 00:00:37.183 READ DMA EXT 25 00 00 00 10 00 00 1e 1d 5f 80 e0 00 00:00:37.183 READ DMA EXT 25 00 00 00 08 00 00 1e 1c d5 20 e0 00 00:00:37.183 READ DMA EXT Error 395 [2] occurred at disk power-on lifetime: 13181 hours (549 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 14 df 4a e0 00 Error: UNC 6 sectors at LBA = 0x0014df4a = 1367882 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 14 df 48 e0 00 00:00:01.776 READ DMA EXT 35 00 00 00 08 00 00 19 eb eb 98 e0 00 00:00:01.776 WRITE DMA EXT 25 00 00 00 10 00 00 1e 21 8a 50 e0 00 00:00:01.776 READ DMA EXT 35 00 00 00 10 00 00 00 5e 75 70 e0 00 00:00:01.776 WRITE DMA EXT 25 00 00 00 80 00 00 00 14 df 48 e0 00 00:00:01.774 READ DMA EXT Error 394 [1] occurred at disk power-on lifetime: 13181 hours (549 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7e 00 00 00 14 df 4a e0 00 Error: UNC 126 sectors at LBA = 0x0014df4a = 1367882 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 00 14 df 48 e0 00 00:00:01.774 READ DMA EXT 25 00 00 00 08 00 00 1e 22 fb e0 e0 00 00:00:01.774 READ DMA EXT 25 00 00 00 08 00 00 1e 21 b9 08 e0 00 00:00:01.774 READ DMA EXT 35 00 00 00 08 00 00 00 5e 07 f8 e0 00 00:00:01.774 WRITE DMA EXT 25 00 00 00 08 00 00 00 14 df 48 e0 00 00:00:01.772 READ DMA EXT Error 393 [0] occurred at disk power-on lifetime: 13046 hours (543 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7e 00 00 00 14 df 4a e0 00 Error: UNC 126 sectors at LBA = 0x0014df4a = 1367882 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 00 14 df 48 e0 00 00:00:00.033 READ DMA EXT 25 00 00 00 80 00 00 00 14 de c8 e0 00 00:00:00.033 READ DMA EXT 25 00 00 00 80 00 00 00 14 de 48 e0 00 00:00:00.033 READ DMA EXT 25 00 00 00 80 00 00 00 14 dd c8 e0 00 00:00:00.033 READ DMA EXT 25 00 00 00 80 00 00 00 14 dd 48 e0 00 00:00:00.033 READ DMA EXT Error 392 [7] occurred at disk power-on lifetime: 13181 hours (549 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 7e 00 00 00 14 df 4a e0 00 Error: UNC 126 sectors at LBA = 0x0014df4a = 1367882 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 00 14 df 48 e0 00 00:00:01.770 READ DMA EXT 35 00 00 00 08 00 00 00 00 21 78 e0 00 00:00:01.770 WRITE DMA EXT 35 00 00 00 08 00 00 19 eb eb 90 e0 00 00:00:01.770 WRITE DMA EXT 35 00 00 00 20 00 00 00 5e 75 50 e0 00 00:00:01.770 WRITE DMA EXT 35 00 00 00 08 00 00 00 28 e4 60 e0 00 00:00:01.770 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 19950 - # 2 Extended offline Interrupted (host reset) 90% 19614 - # 3 Short offline Completed without error 00% 18795 - # 4 Short offline Completed without error 00% 18783 - # 5 Short offline Completed without error 00% 18747 - # 6 Short offline Completed without error 00% 18727 - # 7 Short offline Completed without error 00% 16856 - # 8 Extended offline Completed without error 00% 16833 - # 9 Short offline Completed without error 00% 16817 - #10 Short offline Completed without error 00% 16794 - #11 Short offline Completed without error 00% 16770 - #12 Short offline Completed without error 00% 16746 - #13 Short offline Completed without error 00% 16722 - #14 Short offline Completed without error 00% 16708 - #15 Short offline Completed without error 00% 16632 - #16 Short offline Completed without error 00% 16616 - #17 Short offline Completed without error 00% 16601 - #18 Short offline Completed without error 00% 16580 - #19 Short offline Completed without error 00% 16559 - #20 Short offline Completed without error 00% 16533 - #21 Short offline Completed without error 00% 16485 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 28/31 Celsius Lifetime Min/Max Temperature: 13/63 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (85) Index Estimated Time Temperature Celsius 86 2022-03-12 05:30 28 ********* ... ..( 20 skipped). .. ********* 107 2022-03-12 07:15 28 ********* 108 2022-03-12 07:20 29 ********** 109 2022-03-12 07:25 29 ********** 110 2022-03-12 07:30 28 ********* 111 2022-03-12 07:35 29 ********** ... ..( 2 skipped). .. ********** 114 2022-03-12 07:50 29 ********** 115 2022-03-12 07:55 30 *********** ... ..( 14 skipped). .. *********** 2 2022-03-12 09:10 30 *********** 3 2022-03-12 09:15 29 ********** ... ..( 3 skipped). .. ********** 7 2022-03-12 09:35 29 ********** 8 2022-03-12 09:40 30 *********** ... ..( 16 skipped). .. *********** 25 2022-03-12 11:05 30 *********** 26 2022-03-12 11:10 29 ********** 27 2022-03-12 11:15 28 ********* 28 2022-03-12 11:20 28 ********* 29 2022-03-12 11:25 28 ********* 30 2022-03-12 11:30 29 ********** 31 2022-03-12 11:35 30 *********** ... ..( 15 skipped). .. *********** 47 2022-03-12 12:55 30 *********** 48 2022-03-12 13:00 29 ********** 49 2022-03-12 13:05 29 ********** 50 2022-03-12 13:10 30 *********** ... ..( 7 skipped). .. *********** 58 2022-03-12 13:50 30 *********** 59 2022-03-12 13:55 31 ************ ... ..( 2 skipped). .. ************ 62 2022-03-12 14:10 31 ************ 63 2022-03-12 14:15 30 *********** ... ..( 2 skipped). .. *********** 66 2022-03-12 14:30 30 *********** 67 2022-03-12 14:35 31 ************ 68 2022-03-12 14:40 30 *********** ... ..( 6 skipped). .. *********** 75 2022-03-12 15:15 30 *********** 76 2022-03-12 15:20 29 ********** 77 2022-03-12 15:25 30 *********** ... ..( 7 skipped). .. *********** 85 2022-03-12 16:05 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 9 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Samsung based SSDs Device Model: Samsung SSD 840 Series Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: DXT08B0Q User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sat Mar 12 16:05:38 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (53956) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 096 096 000 - 18309 12 Power_Cycle_Count -O--CK 093 093 000 - 6477 177 Wear_Leveling_Count PO--C- 090 090 000 - 120 179 Used_Rsvd_Blk_Cnt_Tot PO--C- 100 100 010 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 010 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 010 - 0 183 Runtime_Bad_Block PO--C- 100 100 010 - 0 187 Uncorrectable_Error_Cnt -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O--CK 070 043 000 - 30 195 ECC_Error_Rate -O-RC- 200 200 000 - 0 199 CRC_Error_Count -OSRCK 099 099 000 - 257 235 POR_Recovery_Count -O--C- 099 099 000 - 2044 241 Total_LBAs_Written -O--CK 099 099 000 - 41575017301 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 1 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 17276 - # 2 Extended offline Completed without error 00% 17115 - # 3 Offline Completed without error 00% 9318 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing 255 0 65535 Read_scanning was never started Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SCT command executing in background (5) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 26/40 Celsius Lifetime Min/Max Temperature: 0/70 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 3 (Unknown, should be 2) Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 128 (93) Index Estimated Time Temperature Celsius 94 2022-03-12 13:58 ? - ... ..( 32 skipped). .. - 127 2022-03-12 14:31 ? - 0 2022-03-12 14:32 40 ********************* 1 2022-03-12 14:33 26 ******* 2 2022-03-12 14:34 28 ********* 3 2022-03-12 14:35 28 ********* 4 2022-03-12 14:36 29 ********** ... ..( 5 skipped). .. ********** 10 2022-03-12 14:42 29 ********** 11 2022-03-12 14:43 30 *********** ... ..( 24 skipped). .. *********** 36 2022-03-12 15:08 30 *********** 37 2022-03-12 15:09 28 ********* 38 2022-03-12 15:10 28 ********* 39 2022-03-12 15:11 28 ********* 40 2022-03-12 15:12 29 ********** 41 2022-03-12 15:13 30 *********** ... ..( 6 skipped). .. *********** 48 2022-03-12 15:20 30 *********** 49 2022-03-12 15:21 29 ********** ... ..( 15 skipped). .. ********** 65 2022-03-12 15:37 29 ********** 66 2022-03-12 15:38 30 *********** ... ..( 6 skipped). .. *********** 73 2022-03-12 15:45 30 *********** 74 2022-03-12 15:46 29 ********** ... ..( 17 skipped). .. ********** 92 2022-03-12 16:04 29 ********** 93 2022-03-12 16:05 30 *********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9500325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001SDM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Mar 12 16:05:38 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 144) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 113 083 006 - 58107513 3 Spin_Up_Time PO---- 099 098 000 - 0 4 Start_Stop_Count -O--CK 090 090 020 - 11046 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 10 7 Seek_Error_Rate POSR-- 087 060 030 - 576831878 9 Power_On_Hours -O--CK 082 082 000 - 16260 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 092 037 020 - 8549 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 5651 188 Command_Timeout -O--CK 100 098 000 - 196717 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 069 043 045 Past 31 (0 1 33 29 0) 191 G-Sense_Error_Rate -O--CK 099 099 000 - 2014 192 Power-Off_Retract_Count -O--CK 100 100 000 - 455 193 Load_Cycle_Count -O--CK 001 001 000 - 206366 194 Temperature_Celsius -O---K 031 057 000 - 31 (0 19 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 045 037 000 - 58107513 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 5645 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5645 [4] occurred at disk power-on lifetime: 14716 hours (613 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1b 3f 27 94 00 00 Error: UNC at LBA = 0x1b3f2794 = 457123732 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 3f 00 00 1b 3a b8 3f 40 00 03:12:14.162 READ FPDMA QUEUED 60 00 00 00 3f 00 00 1b 3a b8 00 40 00 03:12:14.146 READ FPDMA QUEUED b0 00 d0 00 01 00 00 00 c2 4f 01 b0 00 03:12:13.948 SMART READ DATA 2f 00 00 00 01 00 00 00 00 00 10 28 00 03:12:13.903 READ LOG EXT 60 00 00 01 00 00 00 1b 3a c3 00 40 00 03:12:09.181 READ FPDMA QUEUED Error 5644 [3] occurred at disk power-on lifetime: 14716 hours (613 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1b 3f 27 94 00 00 Error: UNC at LBA = 0x1b3f2794 = 457123732 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 1b 3a c3 00 40 00 03:12:09.181 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b 3a c2 00 40 00 03:12:09.181 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b 3a c1 00 40 00 03:12:09.181 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b 3a c0 00 40 00 03:12:09.179 READ FPDMA QUEUED 60 00 00 01 00 00 00 1b 3a bf 00 40 00 03:12:09.176 READ FPDMA QUEUED Error 5643 [2] occurred at disk power-on lifetime: 14715 hours (613 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0e 66 e3 15 00 00 Error: UNC at LBA = 0x0e66e315 = 241623829 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 3f 00 00 0e 61 a8 3f 40 00 02:36:41.658 READ FPDMA QUEUED 60 00 00 00 3f 00 00 0e 61 a8 00 40 00 02:36:41.602 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 28 00 02:36:41.500 READ LOG EXT 60 00 00 01 00 00 00 0e 64 ff 00 40 00 02:36:38.363 READ FPDMA QUEUED 60 00 00 01 00 00 00 0e 64 fe 00 40 00 02:36:38.363 READ FPDMA QUEUED Error 5642 [1] occurred at disk power-on lifetime: 14715 hours (613 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0e 66 e3 15 00 00 Error: UNC at LBA = 0x0e66e315 = 241623829 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 00 00 00 0e 64 ff 00 40 00 02:36:38.363 READ FPDMA QUEUED 60 00 00 01 00 00 00 0e 64 fe 00 40 00 02:36:38.363 READ FPDMA QUEUED 60 00 00 01 00 00 00 0e 64 fd 00 40 00 02:36:38.363 READ FPDMA QUEUED 60 00 00 01 00 00 00 0e 64 fc 00 40 00 02:36:38.363 READ FPDMA QUEUED 60 00 00 01 00 00 00 0e 64 fb 00 40 00 02:36:38.336 READ FPDMA QUEUED Error 5641 [0] occurred at disk power-on lifetime: 14609 hours (608 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 1b 3f 27 94 00 00 Error: UNC at LBA = 0x1b3f2794 = 457123732 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 00 1b 3f 27 00 40 00 11:25:22.737 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 1b 36 41 00 40 00 11:25:17.846 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 1b 36 40 00 40 00 11:25:17.828 READ VERIFY SECTOR(S) EXT b0 00 d0 00 01 00 00 00 c2 4f 01 a0 00 11:25:17.702 SMART READ DATA 42 00 00 01 00 00 00 1b 2f 65 00 40 00 11:25:14.355 READ VERIFY SECTOR(S) EXT Error 5640 [19] occurred at disk power-on lifetime: 14609 hours (608 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0e 66 e3 15 00 00 Error: UNC at LBA = 0x0e66e315 = 241623829 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 01 00 00 00 0e 66 e3 00 40 00 10:59:05.445 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 0e 5d 22 00 40 00 10:59:01.038 READ VERIFY SECTOR(S) EXT 42 00 00 01 00 00 00 0e 5d 21 00 40 00 10:59:01.010 READ VERIFY SECTOR(S) EXT b0 00 d0 00 01 00 00 00 c2 4f 01 a0 00 10:59:00.871 SMART READ DATA 42 00 00 01 00 00 00 0e 54 7a 00 40 00 10:58:56.956 READ VERIFY SECTOR(S) EXT Error 5639 [18] occurred at disk power-on lifetime: 14461 hours (602 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0e 66 e3 15 00 00 Error: WP at LBA = 0x0e66e315 = 241623829 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 0e fc f8 c0 40 00 03:46:56.345 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 0f d7 c8 20 40 00 03:46:56.342 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 1c dc ad 60 40 00 03:46:56.341 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 0e fc f8 c0 40 00 03:46:56.341 READ FPDMA QUEUED 61 00 00 00 08 00 00 0e fc f8 90 40 00 03:46:56.340 WRITE FPDMA QUEUED Error 5638 [17] occurred at disk power-on lifetime: 14461 hours (602 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 0e 66 e3 15 00 00 Error: WP at LBA = 0x0e66e315 = 241623829 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 01 a0 16 98 40 00 03:46:53.782 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 0e f7 53 90 40 00 03:46:53.781 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 01 fb cf 50 40 00 03:46:53.781 WRITE FPDMA QUEUED 60 00 00 00 20 00 00 0e 66 e3 00 40 00 03:46:53.780 READ FPDMA QUEUED 61 00 00 00 01 00 00 01 e0 1a 98 40 00 03:46:53.780 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 15780 457123732 # 2 Extended offline Completed: read failure 90% 15779 457123732 # 3 Extended offline Completed: read failure 90% 15659 457123732 # 4 Extended offline Completed: read failure 90% 15659 457123732 # 5 Extended offline Completed: read failure 90% 15615 457123732 # 6 Extended offline Completed: read failure 90% 15614 457123733 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 29/33 Celsius Lifetime Min/Max Temperature: 19/57 Celsius Under/Over Temperature Limit Count: 0/188 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (67) Index Estimated Time Temperature Celsius 68 2022-03-12 13:58 31 ************ ... ..( 43 skipped). .. ************ 112 2022-03-12 14:42 31 ************ 113 2022-03-12 14:43 30 *********** ... ..( 23 skipped). .. *********** 9 2022-03-12 15:07 30 *********** 10 2022-03-12 15:08 29 ********** 11 2022-03-12 15:09 29 ********** 12 2022-03-12 15:10 30 *********** 13 2022-03-12 15:11 30 *********** 14 2022-03-12 15:12 30 *********** 15 2022-03-12 15:13 31 ************ ... ..( 2 skipped). .. ************ 18 2022-03-12 15:16 31 ************ 19 2022-03-12 15:17 30 *********** ... ..( 17 skipped). .. *********** 37 2022-03-12 15:35 30 *********** 38 2022-03-12 15:36 31 ************ ... ..( 6 skipped). .. ************ 45 2022-03-12 15:43 31 ************ 46 2022-03-12 15:44 30 *********** ... ..( 17 skipped). .. *********** 64 2022-03-12 16:02 30 *********** 65 2022-03-12 16:03 31 ************ 66 2022-03-12 16:04 31 ************ 67 2022-03-12 16:05 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M9T Device Model: ST2000LM003 HN-M201RAD Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2BE10001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Mar 12 16:05:38 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 254 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (22680) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 378) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 40 2 Throughput_Performance -OS--K 055 055 000 - 20660 3 Spin_Up_Time PO---K 087 080 025 - 4000 4 Start_Stop_Count -O--CK 064 064 000 - 36603 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 17956 10 Spin_Retry_Count -O--CK 252 252 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3431 191 G-Sense_Error_Rate -O---K 252 252 000 - 0 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 050 000 - 32 (Min/Max 17/52) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 1 198 Offline_Uncorrectable ----CK 252 100 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 355 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 106 223 Load_Retry_Count -O--CK 100 100 000 - 57 225 Load_Cycle_Count -O--CK 010 010 000 - 910321 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 363 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 363 [2] occurred at disk power-on lifetime: 17899 hours (745 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff c0 00 00 00 5e 74 40 40 00 Error: ICRC, ABRT at LBA = 0x005e7440 = 6190144 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 01 d0 00 00 00 5e 74 60 40 00 00:00:35.226 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 5e 72 30 40 00 00:00:35.227 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 5e 6e 30 40 00 00:00:35.227 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 5e 6a 30 40 00 00:00:35.227 READ FPDMA QUEUED 60 00 00 04 00 00 00 00 5e 66 30 40 00 00:00:35.227 READ FPDMA QUEUED Error 362 [1] occurred at disk power-on lifetime: 17899 hours (745 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 21 00 00 25 97 28 0f 40 00 Error: ICRC, ABRT at LBA = 0x2597280f = 630663183 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 da 01 10 00 00 25 97 28 10 40 00 00:00:34.543 WRITE FPDMA QUEUED 61 00 d0 02 00 00 00 25 97 2f 20 40 00 00:00:34.612 WRITE FPDMA QUEUED 61 00 da 02 00 00 00 25 97 2b 20 40 00 00:00:34.612 WRITE FPDMA QUEUED 61 00 00 02 00 00 00 25 97 29 20 40 00 00:00:34.612 WRITE FPDMA QUEUED 61 00 00 02 00 00 00 25 97 27 20 40 00 00:00:34.612 WRITE FPDMA QUEUED Error 361 [0] occurred at disk power-on lifetime: 17898 hours (745 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 61 00 00 25 d2 08 d7 40 00 Error: ICRC, ABRT at LBA = 0x25d208d7 = 634521815 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 02 30 00 00 25 d2 08 d8 40 00 00:00:32.924 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 25 d2 0b 08 40 00 00:00:33.070 WRITE FPDMA QUEUED 61 00 d0 04 00 00 00 25 d2 07 08 40 00 00:00:33.070 WRITE FPDMA QUEUED 61 00 d0 00 80 00 00 25 d1 fd 58 40 00 00:00:33.070 WRITE FPDMA QUEUED 61 00 d0 00 38 00 00 25 d1 f7 d0 40 00 00:00:33.070 WRITE FPDMA QUEUED Error 360 [7] occurred at disk power-on lifetime: 17898 hours (745 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff c1 00 00 25 d1 ed 27 40 00 Error: ICRC, ABRT at LBA = 0x25d1ed27 = 634514727 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 20 00 00 25 d1 ed 28 40 00 00:00:32.924 WRITE FPDMA QUEUED 61 00 00 00 80 00 00 25 d1 ec c8 40 00 00:00:33.069 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 25 d1 eb 60 40 00 00:00:33.069 WRITE FPDMA QUEUED 61 00 00 00 20 00 00 25 d1 ea f0 40 00 00:00:33.069 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 25 d1 ea 78 40 00 00:00:33.069 WRITE FPDMA QUEUED Error 359 [6] occurred at disk power-on lifetime: 17603 hours (733 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 01 db 00 00 33 fb 24 c0 40 00 Error: ICRC, ABRT at LBA = 0x33fb24c0 = 872096960 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 02 d0 00 00 33 fb 24 fb 40 00 00:01:56.118 READ FPDMA QUEUED 60 00 00 02 00 00 00 33 fb 2b cb 40 00 00:01:56.120 READ FPDMA QUEUED 60 00 00 04 00 00 00 33 fb 27 cb 40 00 00:01:56.120 READ FPDMA QUEUED 60 00 00 04 00 00 00 33 fb 23 cb 40 00 00:01:56.120 READ FPDMA QUEUED 60 00 00 00 30 00 00 33 fb 23 9b 40 00 00:01:56.120 READ FPDMA QUEUED Error 358 [5] occurred at disk power-on lifetime: 17603 hours (733 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff b0 00 00 00 00 f3 80 40 00 Error: ICRC, ABRT at LBA = 0x0000f380 = 62336 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 00 00 00 f3 90 40 00 00:01:56.033 READ FPDMA QUEUED 60 00 d0 00 80 00 00 00 00 f3 20 40 00 00:01:56.034 READ FPDMA QUEUED 61 00 d0 00 08 00 00 00 5c 36 48 40 00 00:01:56.034 WRITE FPDMA QUEUED 61 00 d0 00 18 00 00 00 5d 31 c8 40 00 00:01:56.034 WRITE FPDMA QUEUED 61 00 d0 00 0b 00 00 00 00 f3 15 c0 00 00:01:56.034 WRITE FPDMA QUEUED Error 357 [4] occurred at disk power-on lifetime: 17603 hours (733 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 40 00 00 00 00 ef 40 40 00 Error: ICRC, ABRT at LBA = 0x0000ef40 = 61248 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 00 00 00 ef 60 40 00 00:01:56.026 READ FPDMA QUEUED 60 00 00 00 60 00 00 00 00 ef 40 40 00 00:01:56.028 READ FPDMA QUEUED 61 00 00 00 08 00 00 00 5c 36 48 40 00 00:01:56.028 WRITE FPDMA QUEUED 61 00 00 00 10 00 00 00 5d 2a a0 40 00 00:01:56.028 WRITE FPDMA QUEUED 61 00 00 00 06 00 00 00 00 ef 33 c0 00 00:01:56.028 WRITE FPDMA QUEUED Error 356 [3] occurred at disk power-on lifetime: 17603 hours (733 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 ff 70 00 00 1e cb 58 c0 40 00 Error: ICRC, ABRT at LBA = 0x1ecb58c0 = 516643008 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 d0 00 30 00 00 1e cb 58 d0 40 00 00:01:55.582 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e cb 58 00 40 00 00:01:55.584 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e cb 57 00 40 00 00:01:55.584 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e cb 56 00 40 00 00:01:55.584 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e cb 55 00 40 00 00:01:55.584 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 16928 - # 2 Extended offline Interrupted (host reset) 90% 16922 - # 3 Extended offline Interrupted (host reset) 90% 16769 - # 4 Extended offline Interrupted (host reset) 90% 16767 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 32 Celsius Power Cycle Min/Max Temperature: 29/38 Celsius Lifetime Min/Max Temperature: 16/53 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2022-03-12 05:30 32 ************* 116 2022-03-12 05:35 28 ********* ... ..( 56 skipped). .. ********* 45 2022-03-12 10:20 28 ********* 46 2022-03-12 10:25 29 ********** 47 2022-03-12 10:30 29 ********** 48 2022-03-12 10:35 29 ********** 49 2022-03-12 10:40 30 *********** 50 2022-03-12 10:45 31 ************ 51 2022-03-12 10:50 31 ************ 52 2022-03-12 10:55 31 ************ 53 2022-03-12 11:00 32 ************* ... ..( 8 skipped). .. ************* 62 2022-03-12 11:45 32 ************* 63 2022-03-12 11:50 38 ******************* 64 2022-03-12 11:55 33 ************** 65 2022-03-12 12:00 32 ************* ... ..( 10 skipped). .. ************* 76 2022-03-12 12:55 32 ************* 77 2022-03-12 13:00 31 ************ 78 2022-03-12 13:05 31 ************ 79 2022-03-12 13:10 31 ************ 80 2022-03-12 13:15 32 ************* ... ..( 21 skipped). .. ************* 102 2022-03-12 15:05 32 ************* 103 2022-03-12 15:10 31 ************ 104 2022-03-12 15:15 32 ************* 105 2022-03-12 15:20 32 ************* 106 2022-03-12 15:25 31 ************ 107 2022-03-12 15:30 31 ************ 108 2022-03-12 15:35 31 ************ 109 2022-03-12 15:40 32 ************* ... ..( 4 skipped). .. ************* 114 2022-03-12 16:05 32 ************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 4 R_ERR response for data FIS 0x0003 4 4 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 15 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 15 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 4 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 3691 Vendor specific 0x8e07 4 41201 Vendor specific 0x8e08 4 946 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 12959 Vendor specific 0x8e0b 4 80719785 Vendor specific 0x8e0c 4 48157 Vendor specific 0x8e0d 4 7 Vendor specific 0x8e0e 4 5565 Vendor specific 0x8e0f 4 4480 Vendor specific 0x8e10 4 22260 Vendor specific 0x8e11 4 4 Vendor specific /dev/sdf smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-15parrot1-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk SD6SF1M128G1022I Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: X231200 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: Unknown (0x000b) TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Mar 12 16:05:39 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 4 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 --- - 1 9 Power_On_Hours -O--CK 253 100 --- - 15170 12 Power_Cycle_Count -O--CK 100 100 --- - 8324 166 Min_W/E_Cycle -O--CK 100 100 --- - 1120 167 Min_Bad_Block/Die -O--CK 100 100 --- - 29 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 1409 169 Total_Bad_Block -O--CK 100 100 --- - 192 171 Program_Fail_Count -O--CK 100 100 --- - 0 172 Erase_Fail_Count -O--CK 100 100 --- - 0 173 Avg_Write/Erase_Count -O--CK 100 100 --- - 1238 174 Unexpect_Power_Loss_Ct -O--CK 100 100 --- - 4562 187 Reported_Uncorrect -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 064 068 --- - 36 (Min/Max 9/68) 212 SATA_PHY_Error -O--CK 100 100 --- - 131 230 Perc_Write/Erase_Count -O--CK 100 100 --- - 0 0 10522 232 Perc_Avail_Resrvd_Space PO--CK 100 100 004 - 99 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 160211 241 Total_Writes_GiB ----CK 253 253 --- - 57074 242 Total_Reads_GiB ----CK 253 253 --- - 52499 243 Unknown_Marvell_Attr -O--CK 100 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 14622 - # 2 Extended offline Completed without error 00% 14622 - # 3 Extended offline Completed without error 00% 14519 - # 4 Extended offline Completed without error 00% 14518 - # 5 Extended offline Completed without error 00% 11326 - # 6 Extended offline Completed without error 00% 10355 - # 7 Extended offline Interrupted (host reset) 00% 9592 - # 8 Extended offline Completed without error 00% 9574 - # 9 Extended offline Completed without error 00% 9477 - #10 Short offline Completed without error 00% 9313 - #11 Short offline Completed without error 00% 9311 - #12 Short offline Completed without error 00% 9298 - #13 Short offline Completed without error 00% 9268 - #14 Extended offline Completed without error 00% 9253 - #15 Short offline Completed without error 00% 9247 - #16 Short offline Completed without error 00% 9241 - #17 Short offline Completed without error 00% 9239 - #18 Short offline Completed without error 00% 9230 - #19 Short offline Completed without error 00% 9223 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 41 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 8 Command failed due to ICRC error 0x0002 4 9 R_ERR response for data FIS 0x0005 4 4 R_ERR response for non-data FIS 0x000a 4 20 Device-to-host register FISes sent due to a COMRESET