/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Apple SD/SM/TS...E/F/G SSDs Device Model: APPLE SSD SM512E Serial Number: -- LU WWN Device Id: 5 002538 ... Firmware Version: CXM09A1Q User Capacity: 500,277,790,720 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4c SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Jan 10 17:39:49 2023 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x83) Offline data collection activity is in a Reserved state. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1920) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 32) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-RC- 200 200 000 - 0 5 Reallocated_Sector_Ct PO--CK 099 099 000 - 2 9 Power_On_Hours -O--CK 099 099 000 - 4064 12 Power_Cycle_Count -O--CK 075 075 000 - 24473 169 Unknown_Apple_Attrib PO--C- 253 253 010 - 3033102561792 173 Wear_Leveling_Count -O--CK 177 177 100 - 2070220571225 192 Power-Off_Retract_Count -O--C- 095 095 000 - 24418 194 Temperature_Celsius -O---K 046 022 000 - 54 (Min/Max 7/80) 197 Current_Pending_Sector -O---K 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-RC- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 2 Comprehensive SMART error log 0x03 GPL,SL R/O 2 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 2 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 8 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 8 [7] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 80 02 00 00 00 00 5b c8 68 00 00 512 sectors at LBA = 0x005bc868 = 6015080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT Error 7 [6] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 80 02 00 00 00 00 5b c8 68 00 00 512 sectors at LBA = 0x005bc868 = 6015080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT Error 6 [5] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 80 02 00 00 00 00 5b c8 68 00 00 512 sectors at LBA = 0x005bc868 = 6015080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 80 02 00 00 00 00 5b c8 68 00 00 512 sectors at LBA = 0x005bc868 = 6015080 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 5b db 30 13 00 02:42:19.000 READ DMA EXT 25 00 00 02 00 00 00 00 5b c8 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- c0 04 00 00 00 00 5b c6 68 00 00 1024 sectors at LBA = 0x005bc668 = 6014568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 03 f8 00 00 00 5b d7 38 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b db 30 13 00 02:42:19.000 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- c0 04 00 00 00 00 5b c6 68 00 00 1024 sectors at LBA = 0x005bc668 = 6014568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 04 00 00 00 00 5b ce d0 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b db 30 13 00 02:42:19.000 READ DMA EXT 25 00 00 03 f8 00 00 00 5b d7 38 13 00 02:42:19.000 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- c0 04 00 00 00 00 5b c6 68 00 00 1024 sectors at LBA = 0x005bc668 = 6014568 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 03 f8 00 00 00 5b ca d8 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b c6 68 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b db 30 13 00 02:42:19.000 READ DMA EXT 25 00 00 03 f8 00 00 00 5b d7 38 13 00 02:42:19.000 READ DMA EXT 25 00 00 04 00 00 00 00 5b ce d0 13 00 02:42:19.000 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 28 hours (1 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- c0 04 00 00 00 00 5b c6 68 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 49152 R_ERR response for data FIS 0x0003 2 53248 R_ERR response for device-to-host data FIS 0x0004 2 57344 R_ERR response for host-to-device data FIS 0x0005 2 7952 R_ERR response for non-data FIS 0x0006 2 2562 R_ERR response for device-to-host non-data FIS 0x0007 2 4096 R_ERR response for host-to-device non-data FIS 0x0008 2 7952 Device-to-host non-data FIS retries 0x0009 2 7953 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5420 Device-to-host register FISes sent due to a COMRESET 0x000b 2 6145 CRC errors within host-to-device FIS 0x000d 2 7953 Non-CRC errors within host-to-device FIS 0x000f 2 8176 R_ERR response for host-to-device data FIS, CRC 0x0010 2 15 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 49153 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 12112 R_ERR response for host-to-device non-data FIS, non-CRC