/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: APPLE HDD ST3000DM001 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: AP18 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 1 08:51:33 2024 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 330) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x10bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 106 097 006 - 1168816 3 Spin_Up_Time PO---- 094 094 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 4013 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 065 057 030 - 68770121979 9 Power_On_Hours -O--CK 071 071 000 - 26231 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4183 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 090 090 000 - 10 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 059 043 045 Past 41 (255 255 41 29 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 108 193 Load_Cycle_Count -O--CK 098 098 000 - 4185 194 Temperature_Celsius -O---K 041 057 000 - 41 (0 15 0 0 0) 197 Current_Pending_Sector -O--C- 093 093 000 - 1152 198 Offline_Uncorrectable ----C- 093 093 000 - 1152 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 26515h+48m+03.951s 241 Total_LBAs_Written ------ 100 253 000 - 9964315357 242 Total_LBAs_Read ------ 100 253 000 - 12440313214 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 132 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa5 GPL,SL VS 132 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5288 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 36 40 00 00 Error: UNC at LBA = 0x03213640 = 52508224 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:34.545 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:30.869 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:27.127 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:23.495 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:07:23.341 READ LOG EXT Error 9 [8] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 36 30 00 00 Error: UNC at LBA = 0x03213630 = 52508208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:30.869 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:27.127 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:23.495 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:07:23.341 READ LOG EXT 60 00 00 00 48 00 00 03 21 36 08 40 00 02:07:18.603 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 36 30 00 00 Error: UNC at LBA = 0x03213630 = 52508208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:27.127 READ DMA EXT 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:23.495 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:07:23.341 READ LOG EXT 60 00 00 00 48 00 00 03 21 36 08 40 00 02:07:18.603 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 84 08 40 00 02:07:18.603 READ FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 36 30 00 00 Error: UNC at LBA = 0x03213630 = 52508208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 48 00 00 03 21 36 08 40 00 02:07:23.495 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:07:23.341 READ LOG EXT 60 00 00 00 48 00 00 03 21 36 08 40 00 02:07:18.603 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 84 08 40 00 02:07:18.603 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 83 e0 40 00 02:07:18.602 READ FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 36 30 00 00 Error: UNC at LBA = 0x03213630 = 52508208 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 48 00 00 03 21 36 08 40 00 02:07:18.603 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 84 08 40 00 02:07:18.603 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 83 e0 40 00 02:07:18.602 READ FPDMA QUEUED 60 00 00 00 48 00 00 03 21 83 98 40 00 02:07:18.602 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 83 78 40 00 02:07:18.601 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 34 c8 00 00 Error: UNC at LBA = 0x032134c8 = 52507848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:22.497 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:18.838 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:15.271 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:11.646 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:06:11.555 READ LOG EXT Error 4 [3] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 34 c8 00 00 Error: UNC at LBA = 0x032134c8 = 52507848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:18.838 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:15.271 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:11.646 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:06:11.555 READ LOG EXT 60 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:07.672 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 25999 hours (1083 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 03 21 34 c8 00 00 Error: UNC at LBA = 0x032134c8 = 52507848 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:15.271 READ DMA EXT 25 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:11.646 READ DMA EXT 2f 00 00 00 01 00 00 00 00 00 10 00 00 02:06:11.555 READ LOG EXT 60 00 00 00 08 00 00 03 21 34 c8 40 00 02:06:07.672 READ FPDMA QUEUED 60 00 00 00 08 00 00 03 21 34 48 40 00 02:06:07.664 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 21/39 Celsius Lifetime Min/Max Temperature: 15/57 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 3/62 Celsius Min/Max Temperature Limit: 0/65 Celsius Temperature History Size (Index): 128 (118) Index Estimated Time Temperature Celsius 119 2023-12-27 03:58 38 ******************* 120 2023-12-27 04:57 ? - 121 2023-12-27 05:56 37 ****************** 122 2023-12-27 06:55 ? - 123 2023-12-27 07:54 26 ******* 124 2023-12-27 08:53 ? - 125 2023-12-27 09:52 23 **** 126 2023-12-27 10:51 43 ************************ 127 2023-12-27 11:50 47 **************************** 0 2023-12-27 12:49 48 ***************************** ... ..( 2 skipped). .. ***************************** 3 2023-12-27 15:46 48 ***************************** 4 2023-12-27 16:45 46 *************************** 5 2023-12-27 17:44 46 *************************** 6 2023-12-27 18:43 45 ************************** 7 2023-12-27 19:42 45 ************************** 8 2023-12-27 20:41 46 *************************** 9 2023-12-27 21:40 ? - 10 2023-12-27 22:39 31 ************ 11 2023-12-27 23:38 44 ************************* 12 2023-12-28 00:37 46 *************************** ... ..( 4 skipped). .. *************************** 17 2023-12-28 05:32 46 *************************** 18 2023-12-28 06:31 45 ************************** 19 2023-12-28 07:30 44 ************************* ... ..( 4 skipped). .. ************************* 24 2023-12-28 12:25 44 ************************* 25 2023-12-28 13:24 43 ************************ ... ..( 8 skipped). .. ************************ 34 2023-12-28 22:15 43 ************************ 35 2023-12-28 23:14 45 ************************** 36 2023-12-29 00:13 46 *************************** 37 2023-12-29 01:12 46 *************************** 38 2023-12-29 02:11 46 *************************** 39 2023-12-29 03:10 45 ************************** ... ..( 2 skipped). .. ************************** 42 2023-12-29 06:07 45 ************************** 43 2023-12-29 07:06 ? - 44 2023-12-29 08:05 41 ********************** 45 2023-12-29 09:04 ? - 46 2023-12-29 10:03 35 **************** 47 2023-12-29 11:02 ? - 48 2023-12-29 12:01 32 ************* 49 2023-12-29 13:00 ? - 50 2023-12-29 13:59 38 ******************* 51 2023-12-29 14:58 ? - 52 2023-12-29 15:57 35 **************** 53 2023-12-29 16:56 ? - 54 2023-12-29 17:55 33 ************** 55 2023-12-29 18:54 ? - 56 2023-12-29 19:53 34 *************** 57 2023-12-29 20:52 ? - 58 2023-12-29 21:51 35 **************** 59 2023-12-29 22:50 ? - 60 2023-12-29 23:49 22 *** 61 2023-12-30 00:48 ? - 62 2023-12-30 01:47 22 *** 63 2023-12-30 02:46 ? - 64 2023-12-30 03:45 22 *** 65 2023-12-30 04:44 42 *********************** 66 2023-12-30 05:43 45 ************************** 67 2023-12-30 06:42 46 *************************** 68 2023-12-30 07:41 46 *************************** 69 2023-12-30 08:40 45 ************************** 70 2023-12-30 09:39 45 ************************** 71 2023-12-30 10:38 44 ************************* 72 2023-12-30 11:37 43 ************************ ... ..( 2 skipped). .. ************************ 75 2023-12-30 14:34 43 ************************ 76 2023-12-30 15:33 ? - 77 2023-12-30 16:32 43 ************************ 78 2023-12-30 17:31 ? - 79 2023-12-30 18:30 29 ********** 80 2023-12-30 19:29 44 ************************* 81 2023-12-30 20:28 46 *************************** 82 2023-12-30 21:27 ? - 83 2023-12-30 22:26 44 ************************* 84 2023-12-30 23:25 44 ************************* 85 2023-12-31 00:24 ? - 86 2023-12-31 01:23 39 ******************** 87 2023-12-31 02:22 41 ********************** 88 2023-12-31 03:21 ? - 89 2023-12-31 04:20 30 *********** 90 2023-12-31 05:19 ? - 91 2023-12-31 06:18 33 ************** 92 2023-12-31 07:17 47 **************************** 93 2023-12-31 08:16 43 ************************ 94 2023-12-31 09:15 46 *************************** 95 2023-12-31 10:14 41 ********************** 96 2023-12-31 11:13 39 ******************** 97 2023-12-31 12:12 38 ******************* 98 2023-12-31 13:11 38 ******************* 99 2023-12-31 14:10 38 ******************* 100 2023-12-31 15:09 39 ******************** 101 2023-12-31 16:08 39 ******************** 102 2023-12-31 17:07 38 ******************* 103 2023-12-31 18:06 38 ******************* 104 2023-12-31 19:05 38 ******************* 105 2023-12-31 20:04 45 ************************** 106 2023-12-31 21:03 40 ********************* 107 2023-12-31 22:02 39 ******************** 108 2023-12-31 23:01 39 ******************** 109 2024-01-01 00:00 40 ********************* 110 2024-01-01 00:59 44 ************************* 111 2024-01-01 01:58 41 ********************** 112 2024-01-01 02:57 39 ******************** 113 2024-01-01 03:56 44 ************************* 114 2024-01-01 04:55 51 ******************************** 115 2024-01-01 05:54 44 ************************* 116 2024-01-01 06:53 43 ************************ 117 2024-01-01 07:52 ? - 118 2024-01-01 08:51 21 ** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.2.0-39-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Apple SD/SM/TS...E/F/G SSDs Device Model: APPLE SSD SD0128F Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: A222621 User Capacity: 121,332,826,112 bytes [121 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 3.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Jan 1 08:51:33 2024 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x00) Offline data collection not supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. SMART Attributes Data Structure revision number: 40 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 000 - 0 5 Reallocated_Sector_Ct POSR-- 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 3035 12 Power_Cycle_Count -O--CK 100 100 000 - 4062 169 Unknown_Apple_Attrib -O---K 100 100 010 - 700253734624 173 Wear_Leveling_Count -O---K 185 185 100 - 1017936806224 174 Host_Reads_MiB ----CK 100 100 000 - 20002896 175 Host_Writes_MiB ----CK 100 100 000 - 16249850 192 Power-Off_Retract_Count -O--CK 100 100 000 - 108 194 Temperature_Celsius -O---K 045 045 000 - 55 (Min/Max 21/86) 197 Current_Pending_Sector -O--CK 000 000 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 244 Unknown_Attribute -O---- 000 000 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xaa GPL,SL VS 4 Device vendor specific log 0xab GPL,SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test Log not supported Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET