/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-48-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Crucial/Micron Client SSDs Device Model: CT1000MX500SSD1 Serial Number: -- LU WWN Device Id: 5 00a075 ... Firmware Version: M3CR022 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 1 03:04:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 000 - 0 5 Reallocate_NAND_Blk_Cnt -O--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 4632 12 Power_Cycle_Count -O--CK 100 100 000 - 1320 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 173 Ave_Block-Erase_Count -O--CK 096 096 000 - 64 174 Unexpect_Power_Loss_Ct -O--CK 100 100 000 - 44 180 Unused_Reserve_NAND_Blk PO--CK 000 000 000 - 42 183 SATA_Interfac_Downshift -O--CK 100 100 000 - 0 184 Error_Correction_Count -O--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 064 044 000 - 36 (Min/Max 0/56) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_ECC_Cnt -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 19 202 Percent_Lifetime_Remain ----CK 096 096 001 - 4 206 Write_Error_Rate -OSR-- 100 100 000 - 0 210 Success_RAIN_Recov_Cnt -O--CK 100 100 000 - 0 246 Total_LBAs_Written -O--CK 100 100 000 - 25700764731 247 Host_Program_Page_Count -O--CK 100 100 000 - 419463294 248 FTL_Program_Page_Count -O--CK 100 100 000 - 1030028709 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x24 GPL R/O 88 Current Device Internal Status Data log 0x25 GPL R/O 64 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 518 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 25/41 Celsius Lifetime Min/Max Temperature: 0/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: 0/100 Celsius Temperature History Size (Index): 128 (18) Index Estimated Time Temperature Celsius 19 2022-10-01 00:57 38 ******************* 20 2022-10-01 00:58 38 ******************* 21 2022-10-01 00:59 36 ***************** 22 2022-10-01 01:00 36 ***************** 23 2022-10-01 01:01 41 ********************** 24 2022-10-01 01:02 36 ***************** 25 2022-10-01 01:03 38 ******************* 26 2022-10-01 01:04 36 ***************** ... ..( 4 skipped). .. ***************** 31 2022-10-01 01:09 36 ***************** 32 2022-10-01 01:10 38 ******************* 33 2022-10-01 01:11 36 ***************** 34 2022-10-01 01:12 36 ***************** 35 2022-10-01 01:13 41 ********************** 36 2022-10-01 01:14 38 ******************* 37 2022-10-01 01:15 36 ***************** ... ..( 4 skipped). .. ***************** 42 2022-10-01 01:20 36 ***************** 43 2022-10-01 01:21 38 ******************* 44 2022-10-01 01:22 36 ***************** 45 2022-10-01 01:23 36 ***************** 46 2022-10-01 01:24 38 ******************* 47 2022-10-01 01:25 36 ***************** 48 2022-10-01 01:26 36 ***************** 49 2022-10-01 01:27 38 ******************* 50 2022-10-01 01:28 36 ***************** ... ..( 6 skipped). .. ***************** 57 2022-10-01 01:35 36 ***************** 58 2022-10-01 01:36 38 ******************* 59 2022-10-01 01:37 36 ***************** ... ..( 5 skipped). .. ***************** 65 2022-10-01 01:43 36 ***************** 66 2022-10-01 01:44 38 ******************* 67 2022-10-01 01:45 36 ***************** ... ..( 2 skipped). .. ***************** 70 2022-10-01 01:48 36 ***************** 71 2022-10-01 01:49 41 ********************** 72 2022-10-01 01:50 ? - 73 2022-10-01 01:51 ? - 74 2022-10-01 01:52 33 ************** 75 2022-10-01 01:53 30 *********** 76 2022-10-01 01:54 30 *********** 77 2022-10-01 01:55 31 ************ 78 2022-10-01 01:56 30 *********** 79 2022-10-01 01:57 33 ************** 80 2022-10-01 01:58 35 **************** 81 2022-10-01 01:59 36 ***************** 82 2022-10-01 02:00 36 ***************** 83 2022-10-01 02:01 36 ***************** 84 2022-10-01 02:02 38 ******************* 85 2022-10-01 02:03 38 ******************* 86 2022-10-01 02:04 36 ***************** 87 2022-10-01 02:05 38 ******************* 88 2022-10-01 02:06 40 ********************* 89 2022-10-01 02:07 40 ********************* 90 2022-10-01 02:08 36 ***************** 91 2022-10-01 02:09 40 ********************* 92 2022-10-01 02:10 40 ********************* 93 2022-10-01 02:11 41 ********************** 94 2022-10-01 02:12 38 ******************* 95 2022-10-01 02:13 40 ********************* 96 2022-10-01 02:14 36 ***************** ... ..( 10 skipped). .. ***************** 107 2022-10-01 02:25 36 ***************** 108 2022-10-01 02:26 35 **************** 109 2022-10-01 02:27 35 **************** 110 2022-10-01 02:28 36 ***************** 111 2022-10-01 02:29 35 **************** 112 2022-10-01 02:30 35 **************** 113 2022-10-01 02:31 35 **************** 114 2022-10-01 02:32 36 ***************** 115 2022-10-01 02:33 35 **************** 116 2022-10-01 02:34 35 **************** 117 2022-10-01 02:35 36 ***************** 118 2022-10-01 02:36 35 **************** 119 2022-10-01 02:37 36 ***************** ... ..( 3 skipped). .. ***************** 123 2022-10-01 02:41 36 ***************** 124 2022-10-01 02:42 35 **************** 125 2022-10-01 02:43 36 ***************** 126 2022-10-01 02:44 36 ***************** 127 2022-10-01 02:45 35 **************** 0 2022-10-01 02:46 35 **************** 1 2022-10-01 02:47 35 **************** 2 2022-10-01 02:48 36 ***************** 3 2022-10-01 02:49 36 ***************** 4 2022-10-01 02:50 35 **************** 5 2022-10-01 02:51 36 ***************** 6 2022-10-01 02:52 35 **************** 7 2022-10-01 02:53 36 ***************** 8 2022-10-01 02:54 35 **************** 9 2022-10-01 02:55 36 ***************** ... ..( 8 skipped). .. ***************** 18 2022-10-01 03:04 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1320 --- Lifetime Power-On Resets 0x01 0x010 4 4632 --- Power-on Hours 0x01 0x018 6 4225928251 --- Logical Sectors Written 0x01 0x020 6 245248800 --- Number of Write Commands 0x01 0x028 6 245868022 --- Logical Sectors Read 0x01 0x030 6 848544430 --- Number of Read Commands 0x01 0x038 6 4294967296 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 45 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 37 --- Average Short Term Temperature 0x05 0x018 1 37 --- Average Long Term Temperature 0x05 0x020 1 56 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 45 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 41 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 9875 --- Number of Hardware Resets 0x06 0x010 4 74 --- Number of ASR Events 0x06 0x018 4 19 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 4 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-48-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD103UJ Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sat Oct 1 03:04:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11683) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 196) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 074 074 011 - 8620 4 Start_Stop_Count -O--CK 096 096 000 - 4271 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Hours -O--CK 095 095 000 - 24681 10 Spin_Retry_Count PO--CK 100 100 051 - 1 11 Calibration_Retry_Count -O--C- 100 100 000 - 1 12 Power_Cycle_Count -O--CK 096 096 000 - 4270 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 079 062 000 - 21 (Min/Max 14/21) 194 Temperature_Celsius -O---K 075 062 000 - 25 (Min/Max 14/25) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 886 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 100 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 2 Write stream error log 0x22 GPL R/O 2 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: --/25 Celsius Lifetime Min/Max Temperature: --/39 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (72) Index Estimated Time Temperature Celsius 73 2022-10-01 00:57 26 ******* ... ..( 25 skipped). .. ******* 99 2022-10-01 01:23 26 ******* 100 2022-10-01 01:24 25 ****** 101 2022-10-01 01:25 26 ******* 102 2022-10-01 01:26 26 ******* 103 2022-10-01 01:27 26 ******* 104 2022-10-01 01:28 25 ****** ... ..( 22 skipped). .. ****** 127 2022-10-01 01:51 25 ****** 0 2022-10-01 01:52 14 - 1 2022-10-01 01:53 15 - 2 2022-10-01 01:54 16 - 3 2022-10-01 01:55 16 - 4 2022-10-01 01:56 17 - 5 2022-10-01 01:57 18 - 6 2022-10-01 01:58 18 - 7 2022-10-01 01:59 18 - 8 2022-10-01 02:00 19 - 9 2022-10-01 02:01 19 - 10 2022-10-01 02:02 20 * 11 2022-10-01 02:03 20 * 12 2022-10-01 02:04 20 * 13 2022-10-01 02:05 21 ** ... ..( 2 skipped). .. ** 16 2022-10-01 02:08 21 ** 17 2022-10-01 02:09 22 *** ... ..( 2 skipped). .. *** 20 2022-10-01 02:12 22 *** 21 2022-10-01 02:13 23 **** ... ..( 6 skipped). .. **** 28 2022-10-01 02:20 23 **** 29 2022-10-01 02:21 24 ***** ... ..( 16 skipped). .. ***** 46 2022-10-01 02:38 24 ***** 47 2022-10-01 02:39 25 ****** 48 2022-10-01 02:40 25 ****** 49 2022-10-01 02:41 24 ***** 50 2022-10-01 02:42 24 ***** 51 2022-10-01 02:43 24 ***** 52 2022-10-01 02:44 25 ****** ... ..( 19 skipped). .. ****** 72 2022-10-01 03:04 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read Device Statistics page 0x00 failed Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdc smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-48-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3320620AS Serial Number: -- Firmware Version: 3.AAK User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Oct 1 03:04:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 115) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 085 006 - 138484693 3 Spin_Up_Time PO---- 095 095 000 - 0 4 Start_Stop_Count -O--CK 095 095 020 - 5247 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 19 7 Seek_Error_Rate POSR-- 078 060 030 - 71921821 9 Power_On_Hours -O--CK 066 066 000 - 29904 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 095 095 020 - 5228 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 039 045 Past 37 (Min/Max 22/37) 194 Temperature_Celsius -O---K 037 061 000 - 37 (0 15 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 065 057 000 - 57715505 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 14749 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdd smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-48-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1CH164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC29 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 1 03:04:57 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 625) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 265) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 087 006 - 155490696 3 Spin_Up_Time PO---- 094 094 000 - 0 4 Start_Stop_Count -O--CK 097 097 020 - 3266 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 075 060 030 - 8650054414 9 Power_On_Hours -O--CK 070 070 000 - 26874 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1732 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 2952 188 Command_Timeout -O--CK 100 099 000 - 5 5 7 189 High_Fly_Writes -O-RCK 099 099 000 - 1 190 Airflow_Temperature_Cel -O---K 064 045 045 Past 36 (Min/Max 20/36) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 160 193 Load_Cycle_Count -O--CK 094 094 000 - 12643 194 Temperature_Celsius -O---K 036 055 000 - 36 (0 14 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 8 198 Offline_Uncorrectable ----C- 100 100 000 - 8 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 25 240 Head_Flying_Hours ------ 100 253 000 - 10433h+59m+38.016s 241 Total_LBAs_Written ------ 100 253 000 - 7428916966 242 Total_LBAs_Read ------ 100 253 000 - 6523195813 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1658 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1658 [17] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 00 03 e7 40 00 00:15:13.100 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5a 00 40 00 00:15:13.100 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8f 40 00 00:15:13.100 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:15:13.099 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:15:13.098 IDENTIFY DEVICE Error 1657 [16] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 00 03 e7 40 00 00:15:09.477 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5a 00 40 00 00:15:09.455 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8f 40 00 00:15:09.454 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8e 40 00 00:15:09.454 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b f8 40 00 00:15:09.454 READ FPDMA QUEUED Error 1656 [15] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 74 b0 5b f8 40 00 00:15:05.793 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b f0 40 00 00:15:05.792 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b e8 40 00 00:15:05.792 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b e0 40 00 00:15:05.792 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b d8 40 00 00:15:05.791 READ FPDMA QUEUED Error 1655 [14] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 00 03 df 40 00 00:15:02.167 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b d0 40 00 00:15:02.146 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b c8 40 00 00:15:02.145 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b c0 40 00 00:15:02.145 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b b8 40 00 00:15:02.145 READ FPDMA QUEUED Error 1654 [13] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 74 b0 5b a8 40 00 00:14:58.483 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b a0 40 00 00:14:58.483 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 98 40 00 00:14:58.482 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 90 40 00 00:14:58.482 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 88 40 00 00:14:58.481 READ FPDMA QUEUED Error 1653 [12] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 74 b0 5b 88 40 00 00:14:54.828 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 80 40 00 00:14:54.828 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 78 40 00 00:14:54.827 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 70 40 00 00:14:54.827 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 68 40 00 00:14:54.826 READ FPDMA QUEUED Error 1652 [11] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 74 b0 5b 60 40 00 00:14:51.163 READ FPDMA QUEUED 60 00 00 00 08 00 00 00 00 03 d7 40 00 00:14:51.163 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8c 40 00 00:14:51.163 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8d 40 00 00:14:51.163 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 8e 40 00 00:14:51.163 READ FPDMA QUEUED Error 1651 [10] occurred at disk power-on lifetime: 1555 hours (64 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 80 34 8b 00 00 Error: UNC at LBA = 0x0080348b = 8402059 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 00 03 d7 40 00 00:14:47.539 READ FPDMA QUEUED 60 00 00 00 08 00 00 74 b0 5b 60 40 00 00:14:47.524 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 92 40 00 00:14:47.509 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 91 40 00 00:14:47.509 READ FPDMA QUEUED 60 00 00 00 01 00 00 00 80 34 90 40 00 00:14:47.509 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 70% 26632 1571017592 # 2 Extended offline Completed: read failure 70% 26630 1571017592 # 3 Conveyance offline Completed without error 00% 26629 - # 4 Conveyance offline Completed without error 00% 21288 - # 5 Extended offline Completed without error 00% 1585 - # 6 Conveyance offline Completed without error 00% 412 - # 7 Short offline Completed without error 00% 412 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 21/36 Celsius Lifetime Min/Max Temperature: 14/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.15.0-48-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SanDisk based SSDs Device Model: SanDisk SDSSDP128G Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: 3.2.0 User Capacity: 126,035,288,064 bytes [126 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 1.8 inches TRIM Command: Available, deterministic Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Oct 1 03:04:58 2022 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x51) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 21) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O---- 100 100 000 - 0 9 Power_On_Hours -O---- 100 100 000 - 11393 12 Power_Cycle_Count -O---- 100 100 000 - 1981 165 Total_Write/Erase_Count -O---- 100 100 000 - 23279 171 Program_Fail_Count -O---- 100 100 000 - 0 172 Erase_Fail_Count -O---- 100 100 000 - 0 173 Avg_Write/Erase_Count -O---- 100 100 000 - 5 174 Unexpect_Power_Loss_Ct -O---- 100 100 000 - 191 187 Reported_Uncorrect -O---- 100 100 000 - 0 194 Temperature_Celsius -O---K 067 033 000 - 33 (Min/Max 4/47) 230 Perc_Write/Erase_Count -O---- 100 100 000 - 16 232 Perc_Avail_Resrvd_Space PO---- 100 100 005 - 0 234 Perc_Write/Erase_Ct_BC -O---- 100 100 000 - 27 241 Total_LBAs_Written -O---- 100 100 000 - 1333305729 242 Total_LBAs_Read -O---- 100 100 000 - 1936707524 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x03 GPL,SL R/O 16 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 1 Device vendor specific log 0xa2 GPL,SL VS 2 Device vendor specific log 0xa3 GPL,SL VS 1 Device vendor specific log 0xa6-0xa7 GPL,SL VS 255 Device vendor specific log Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. SMART Extended Comprehensive Error Log Version: 1 (16 sectors) No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 44 --- Highest Temperature 0x05 0x028 1 20 --- Lowest Temperature 0x05 0x030 1 35 --- Highest Average Short Term Temperature 0x05 0x038 1 35 --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 95 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 6 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0001 2 0 Command failed due to ICRC error