/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.62-1-MANJARO] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-60U6AA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 18.01H18 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5528 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Mon Nov 20 10:21:50 2023 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 43 3 Spin_Up_Time POS--K 143 142 021 - 3833 4 Start_Stop_Count -O--CK 096 096 000 - 4380 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 3 7 Seek_Error_Rate POSR-K 200 200 051 - 0 9 Power_On_Hours -O--CK 081 081 000 - 14504 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4326 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 100 088 000 - 21 188 Command_Timeout -O--CK 100 093 000 - 30065229838 190 Airflow_Temperature_Cel -O---K 063 057 040 - 37 (Min/Max 31/37) 192 Power-Off_Retract_Count -O--CK 200 200 000 - 429 193 Load_Cycle_Count -O--CK 199 199 000 - 3992 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 27 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 27 [2] occurred at disk power-on lifetime: 12919 hours (538 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 08 45 64 f1 40 00 Error: UNC at LBA = 0x084564f1 = 138765553 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 06 00 00 e8 00 00 08 45 6b 00 40 08 00:08:43.191 READ FPDMA QUEUED 60 05 00 00 48 00 00 08 45 66 00 40 08 00:08:43.185 READ FPDMA QUEUED 60 06 00 00 40 00 00 08 45 60 00 40 08 00:08:43.179 READ FPDMA QUEUED 60 06 00 00 e0 00 00 08 45 5a 00 40 08 00:08:43.175 READ FPDMA QUEUED 60 05 00 00 88 00 00 08 45 55 00 40 08 00:08:43.168 READ FPDMA QUEUED Error 26 [1] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:32:55.832 FLUSH CACHE EXT c8 00 00 00 10 00 00 00 af 10 18 e0 08 00:32:53.789 READ DMA ca 00 00 00 20 00 00 00 44 d9 a0 e0 08 00:32:53.789 WRITE DMA ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:32:53.789 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:32:53.788 IDENTIFY DEVICE Error 25 [0] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:32:45.224 FLUSH CACHE EXT ca 00 00 00 20 00 00 00 44 d4 e0 e0 08 00:32:45.224 WRITE DMA ca 00 00 00 60 00 00 00 44 d4 20 e0 08 00:32:45.223 WRITE DMA ca 00 00 00 20 00 00 00 44 d3 e0 e0 08 00:32:45.223 WRITE DMA ca 00 00 00 20 00 00 00 44 d3 20 e0 08 00:32:45.223 WRITE DMA Error 24 [23] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:32:14.162 FLUSH CACHE EXT 61 00 40 00 48 00 00 00 44 35 00 40 08 00:32:14.161 WRITE FPDMA QUEUED 61 00 80 00 40 00 00 00 44 2b 60 40 08 00:32:14.161 WRITE FPDMA QUEUED 61 00 40 00 38 00 00 00 24 35 00 40 08 00:32:14.161 WRITE FPDMA QUEUED 61 00 80 00 30 00 00 00 24 2b 60 40 08 00:32:14.161 WRITE FPDMA QUEUED Error 23 [22] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:31:56.451 FLUSH CACHE EXT 61 00 18 00 38 00 00 00 ee d4 48 40 08 00:31:56.449 WRITE FPDMA QUEUED 61 00 18 00 30 00 00 00 e2 24 98 40 08 00:31:56.449 WRITE FPDMA QUEUED 61 04 20 00 28 00 00 01 3f 4d 58 40 08 00:31:56.448 WRITE FPDMA QUEUED 61 02 c0 00 f8 00 00 01 3f 4a 98 40 08 00:31:56.448 WRITE FPDMA QUEUED Error 22 [21] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 3b 2a a0 40 00 Error: WP at LBA = 0x003b2aa0 = 3877536 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 18 00 00 00 43 fe a0 40 08 00:31:23.043 WRITE FPDMA QUEUED 61 00 20 00 08 00 00 00 23 8d e0 40 08 00:31:23.043 WRITE FPDMA QUEUED 61 00 40 00 00 00 00 01 36 34 b8 40 08 00:31:23.043 WRITE FPDMA QUEUED 60 00 20 00 f0 00 00 00 3b 2a a0 40 08 00:31:22.957 READ FPDMA QUEUED 61 00 20 00 e8 00 00 00 23 fe a0 40 08 00:31:22.957 WRITE FPDMA QUEUED Error 21 [20] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:30:51.988 FLUSH CACHE EXT 61 00 20 00 e0 00 00 00 43 33 80 40 08 00:30:51.988 WRITE FPDMA QUEUED 61 00 20 00 d8 00 00 00 43 2a 60 40 08 00:30:51.987 WRITE FPDMA QUEUED 61 00 20 00 d0 00 00 00 23 33 80 40 08 00:30:51.987 WRITE FPDMA QUEUED 61 00 20 00 c8 00 00 00 23 2a 60 40 08 00:30:51.987 WRITE FPDMA QUEUED Error 20 [19] occurred at disk power-on lifetime: 12459 hours (519 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 f7 df 38 a7 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:25:12.235 FLUSH CACHE EXT 61 00 c0 00 d0 00 00 00 45 f0 40 40 08 00:25:12.234 WRITE FPDMA QUEUED 61 00 80 00 c8 00 00 00 45 c9 80 40 08 00:25:12.234 WRITE FPDMA QUEUED 61 00 60 00 c0 00 00 00 45 c2 20 40 08 00:25:12.234 WRITE FPDMA QUEUED 61 00 80 00 b8 00 00 00 45 bb 40 40 08 00:25:12.233 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 11569 - # 2 Short offline Completed without error 00% 10842 - # 3 Short offline Completed without error 00% 10840 - # 4 Short offline Completed without error 00% 10830 - # 5 Short offline Completed without error 00% 10547 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 31/37 Celsius Lifetime Min/Max Temperature: 0/44 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (98) Index Estimated Time Temperature Celsius 99 2023-11-20 08:14 37 ****************** ... ..( 49 skipped). .. ****************** 21 2023-11-20 09:04 37 ****************** 22 2023-11-20 09:05 ? - 23 2023-11-20 09:06 27 ******** 24 2023-11-20 09:07 28 ********* 25 2023-11-20 09:08 29 ********** 26 2023-11-20 09:09 29 ********** 27 2023-11-20 09:10 29 ********** 28 2023-11-20 09:11 30 *********** 29 2023-11-20 09:12 30 *********** 30 2023-11-20 09:13 31 ************ 31 2023-11-20 09:14 32 ************* ... ..( 2 skipped). .. ************* 34 2023-11-20 09:17 32 ************* 35 2023-11-20 09:18 33 ************** ... ..( 2 skipped). .. ************** 38 2023-11-20 09:21 33 ************** 39 2023-11-20 09:22 34 *************** 40 2023-11-20 09:23 34 *************** 41 2023-11-20 09:24 34 *************** 42 2023-11-20 09:25 35 **************** ... ..( 2 skipped). .. **************** 45 2023-11-20 09:28 35 **************** 46 2023-11-20 09:29 ? - 47 2023-11-20 09:30 28 ********* 48 2023-11-20 09:31 ? - 49 2023-11-20 09:32 27 ******** 50 2023-11-20 09:33 28 ********* 51 2023-11-20 09:34 29 ********** 52 2023-11-20 09:35 29 ********** 53 2023-11-20 09:36 30 *********** 54 2023-11-20 09:37 30 *********** 55 2023-11-20 09:38 ? - 56 2023-11-20 09:39 31 ************ 57 2023-11-20 09:40 31 ************ 58 2023-11-20 09:41 32 ************* 59 2023-11-20 09:42 32 ************* 60 2023-11-20 09:43 32 ************* 61 2023-11-20 09:44 33 ************** 62 2023-11-20 09:45 33 ************** 63 2023-11-20 09:46 33 ************** 64 2023-11-20 09:47 34 *************** 65 2023-11-20 09:48 34 *************** 66 2023-11-20 09:49 34 *************** 67 2023-11-20 09:50 35 **************** ... ..( 6 skipped). .. **************** 74 2023-11-20 09:57 35 **************** 75 2023-11-20 09:58 36 ***************** ... ..( 5 skipped). .. ***************** 81 2023-11-20 10:04 36 ***************** 82 2023-11-20 10:05 37 ****************** 83 2023-11-20 10:06 36 ***************** 84 2023-11-20 10:07 37 ****************** ... ..( 13 skipped). .. ****************** 98 2023-11-20 10:21 37 ****************** SCT Error Recovery Control: Read: 85 (8.5 seconds) Write: 85 (8.5 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 2566 Vendor specific /dev/sdb smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.1.62-1-MANJARO] (local build) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Silicon Motion based SSDs Device Model: ADATA SU630 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: V8X01c83 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5528 ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Mon Nov 20 10:21:50 2023 -05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 7) minutes. Extended self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 2882 12 Power_Cycle_Count -O--CK 100 100 000 - 2709 161 Valid_Spare_Block_Cnt -O--CK 100 100 000 - 0 162 Cache_Block_Count -O--CK 100 100 000 - 93543 163 Initial_Bad_Block_Count -O--CK 100 100 000 - 100 164 Total_Erase_Count -O--CK 100 100 000 - 207 166 Min_Erase_Count -O--CK 100 100 000 - 111 167 Average_Erase_Count -O--CK 100 100 050 - 0 168 Max_Erase_Count_of_Spec -O--CK 100 100 000 - 0 169 Remaining_Lifetime_Perc -O--CK 100 100 000 - 100 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 407 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 1524616 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 51 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 173843 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 43 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 1961 232 Available_Reservd_Space -O--CK 100 100 000 - 100 233 Media_Wearout_Indicator -O--CK 100 100 000 - 335 241 Host_Writes_32MiB -O--CK 100 100 000 - 5447 242 Host_Reads_32MiB -O--CK 100 100 000 - 6784 249 Unkn_SiliconMotion_Attr -O--CK 100 100 000 - 5823 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 12078 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 344 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 344 [7] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 58 00 00 02 50 d2 e8 40 08 Error: UNC at LBA = 0x0250d2e8 = 38851304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 58 00 00 02 50 d2 e8 40 08 01:10:31.324 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:30.938 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:30.938 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:30.904 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:30.891 SET FEATURES [Enable SATA feature] Error 343 [6] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 d8 00 00 02 50 b0 a0 40 08 Error: UNC at LBA = 0x0250b0a0 = 38842528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 d8 00 00 02 50 b0 a0 40 08 01:10:30.806 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:30.414 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:30.414 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:30.380 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:30.367 SET FEATURES [Enable SATA feature] Error 342 [5] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 60 00 00 02 50 d2 e8 40 08 Error: UNC at LBA = 0x0250d2e8 = 38851304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 60 00 00 02 50 d2 e8 40 08 01:10:30.282 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:29.898 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:29.898 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:29.864 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:29.851 SET FEATURES [Enable SATA feature] Error 341 [4] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 40 00 00 02 90 c9 38 40 08 Error: UNC at LBA = 0x0290c938 = 43043128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 02 90 c9 38 40 08 01:10:29.766 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:29.382 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:29.382 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:29.348 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:29.335 SET FEATURES [Enable SATA feature] Error 340 [3] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 50 00 00 02 50 d2 e8 40 08 Error: UNC at LBA = 0x0250d2e8 = 38851304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 50 00 00 02 50 d2 e8 40 08 01:10:29.246 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:28.862 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 00 00 00 00 00 a0 08 01:10:28.862 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 01:10:28.828 SET FEATURES [Set transfer mode] ef 00 10 00 02 00 00 00 00 00 00 a0 08 01:10:28.815 SET FEATURES [Enable SATA feature] Error 339 [2] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 80 00 00 02 50 b0 a0 40 08 Error: UNC at LBA = 0x0250b0a0 = 38842528 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 02 50 b0 a0 40 08 01:10:28.730 READ FPDMA QUEUED 60 00 08 00 78 00 00 02 10 ea 60 40 08 01:10:28.352 READ FPDMA QUEUED 60 00 08 00 70 00 00 02 90 c9 30 40 08 01:10:28.352 READ FPDMA QUEUED 60 00 08 00 68 00 00 02 90 c8 60 40 08 01:10:28.351 READ FPDMA QUEUED 60 00 08 00 60 00 00 01 10 b0 80 40 08 01:10:28.351 READ FPDMA QUEUED Error 338 [1] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 28 00 00 02 50 d2 e8 40 08 Error: UNC at LBA = 0x0250d2e8 = 38851304 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 28 00 00 02 50 d2 e8 40 08 01:10:28.172 READ FPDMA QUEUED 60 00 08 00 20 00 00 02 50 b4 e8 40 08 01:10:27.799 READ FPDMA QUEUED 60 00 30 00 18 00 00 02 4f ba d8 40 08 01:10:27.799 READ FPDMA QUEUED 60 00 08 00 10 00 00 02 4f ba d0 40 08 01:10:27.799 READ FPDMA QUEUED 60 00 d0 00 08 00 00 02 4f ba 00 40 08 01:10:27.799 READ FPDMA QUEUED Error 337 [0] occurred at disk power-on lifetime: 945 hours (39 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 00 00 00 02 90 c9 38 40 08 Error: UNC at LBA = 0x0290c938 = 43043128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 00 00 00 02 90 c9 38 40 08 01:10:27.631 READ FPDMA QUEUED 60 00 08 00 f0 00 00 02 90 c9 20 40 08 01:10:27.261 READ FPDMA QUEUED 60 00 08 00 e8 00 00 02 90 c8 90 40 08 01:10:27.261 READ FPDMA QUEUED 60 00 08 00 e0 00 00 02 90 c8 70 40 08 01:10:27.261 READ FPDMA QUEUED 60 00 08 00 d8 00 00 02 8f c0 00 40 08 01:10:27.261 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/36 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2023-11-20 08:14 ? - ... ..(124 skipped). .. - 127 2023-11-20 10:19 ? - 0 2023-11-20 10:20 36 ***************** 1 2023-11-20 10:21 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2709 --- Lifetime Power-On Resets 0x01 0x010 4 2882 --- Power-on Hours 0x01 0x018 6 11424253779 --- Logical Sectors Written 0x01 0x020 6 137352716 --- Number of Write Commands 0x01 0x028 6 14227767641 --- Logical Sectors Read 0x01 0x030 6 107891015 --- Number of Read Commands 0x01 0x038 6 10377976365 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 352 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 38 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2457 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 83 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET