/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD2500BEVT-24A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A02 User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue May 8 20:35:04 2018 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6780) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 16 3 Spin_Up_Time POS--K 154 147 021 - 1291 4 Start_Stop_Count -O--CK 096 096 000 - 4897 5 Reallocated_Sector_Ct PO--CK 198 198 140 - 16 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5780 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4887 192 Power-Off_Retract_Count -O--CK 199 199 000 - 978 193 Load_Cycle_Count -O--CK 186 186 000 - 42868 194 Temperature_Celsius -O---K 107 079 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 1 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: UNC at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 30 00 00 00 64 a1 40 40 00 01:27:57.984 READ FPDMA QUEUED 61 00 08 00 28 00 00 00 64 a1 28 40 00 01:27:57.984 WRITE FPDMA QUEUED 61 00 20 00 20 00 00 09 85 f5 60 40 00 01:27:57.983 WRITE FPDMA QUEUED 61 00 20 00 18 00 00 09 86 6f 00 40 00 01:27:57.983 WRITE FPDMA QUEUED 60 01 00 00 10 00 00 02 23 3a 40 40 00 01:27:57.965 READ FPDMA QUEUED Error 8 [7] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: UNC at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 d8 00 00 00 64 a1 20 40 00 01:27:55.416 READ FPDMA QUEUED 61 00 08 00 d0 00 00 00 64 97 80 40 00 01:27:55.416 WRITE FPDMA QUEUED 61 00 20 00 c8 00 00 09 85 f5 60 40 00 01:27:55.415 WRITE FPDMA QUEUED 61 00 20 00 c0 00 00 09 86 6e e0 40 00 01:27:55.415 WRITE FPDMA QUEUED 61 00 08 00 b8 00 00 00 5f 06 28 40 00 01:27:55.402 WRITE FPDMA QUEUED Error 7 [6] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: WP at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 10 00 60 00 00 08 a8 8a d8 40 00 01:27:52.991 WRITE FPDMA QUEUED 61 00 20 00 58 00 00 09 85 f5 60 40 00 01:27:52.991 WRITE FPDMA QUEUED 61 00 20 00 50 00 00 09 86 6e c0 40 00 01:27:52.991 WRITE FPDMA QUEUED 60 00 20 00 48 00 00 00 64 97 80 40 00 01:27:52.974 READ FPDMA QUEUED 61 00 08 00 40 00 00 00 64 90 78 40 00 01:27:52.973 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: UNC at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 f8 00 00 00 64 90 60 40 00 01:27:50.415 READ FPDMA QUEUED 61 00 08 00 f0 00 00 00 64 8c 98 40 00 01:27:50.415 WRITE FPDMA QUEUED 61 00 20 00 e8 00 00 09 85 f5 60 40 00 01:27:50.414 WRITE FPDMA QUEUED 61 00 20 00 e0 00 00 09 86 6e 80 40 00 01:27:50.414 WRITE FPDMA QUEUED 60 01 00 00 d8 00 00 02 23 3a 40 40 00 01:27:50.395 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: WP at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a8 00 00 01 81 6e b0 40 00 01:27:47.860 WRITE FPDMA QUEUED 60 00 20 00 a0 00 00 00 64 8c 80 40 00 01:27:47.858 READ FPDMA QUEUED 61 00 08 00 98 00 00 00 63 d2 d8 40 00 01:27:47.858 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 00 63 c1 28 40 00 01:27:47.858 WRITE FPDMA QUEUED 61 00 08 00 88 00 00 00 63 33 00 40 00 01:27:47.857 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: UNC at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 08 00 00 01 cb f5 80 40 00 01:27:45.300 READ FPDMA QUEUED 61 00 10 00 00 00 00 01 cb e7 70 40 00 01:27:45.299 WRITE FPDMA QUEUED 61 00 20 00 f8 00 00 09 85 f5 60 40 00 01:27:45.299 WRITE FPDMA QUEUED 61 00 20 00 f0 00 00 09 86 6e 40 40 00 01:27:45.298 WRITE FPDMA QUEUED 60 01 00 00 e8 00 00 02 23 3a 40 40 00 01:27:45.289 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: WP at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a8 00 00 00 5f 06 20 40 00 01:27:42.746 WRITE FPDMA QUEUED 61 00 08 00 a0 00 00 01 ad c7 68 40 00 01:27:42.746 WRITE FPDMA QUEUED 61 00 08 00 98 00 00 00 5d 89 00 40 00 01:27:42.745 WRITE FPDMA QUEUED 60 00 20 00 90 00 00 01 cb e7 60 40 00 01:27:42.727 READ FPDMA QUEUED 61 00 08 00 88 00 00 00 5f 06 30 40 00 01:27:42.727 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 4826 hours (201 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 00 02 23 3a 70 40 00 Error: WP at LBA = 0x02233a70 = 35863152 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 20 00 f0 00 00 00 60 6f 78 40 00 01:27:40.205 WRITE FPDMA QUEUED 60 01 00 00 e8 00 00 02 23 3a 40 40 00 01:27:40.182 READ FPDMA QUEUED 60 01 00 00 e0 00 00 02 23 3b 40 40 00 01:27:40.182 READ FPDMA QUEUED 60 01 00 00 d8 00 00 02 23 3c 40 40 00 01:27:40.182 READ FPDMA QUEUED 60 01 00 00 d0 00 00 02 23 3d 40 40 00 01:27:40.182 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 36/41 Celsius Lifetime Min/Max Temperature: 36/64 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (38) Index Estimated Time Temperature Celsius 39 2018-05-08 18:28 39 ******************** 40 2018-05-08 18:29 39 ******************** 41 2018-05-08 18:30 39 ******************** 42 2018-05-08 18:31 38 ******************* 43 2018-05-08 18:32 39 ******************** ... ..( 6 skipped). .. ******************** 50 2018-05-08 18:39 39 ******************** 51 2018-05-08 18:40 40 ********************* ... ..( 14 skipped). .. ********************* 66 2018-05-08 18:55 40 ********************* 67 2018-05-08 18:56 41 ********************** 68 2018-05-08 18:57 40 ********************* 69 2018-05-08 18:58 42 *********************** 70 2018-05-08 18:59 42 *********************** 71 2018-05-08 19:00 42 *********************** 72 2018-05-08 19:01 41 ********************** 73 2018-05-08 19:02 42 *********************** ... ..( 3 skipped). .. *********************** 77 2018-05-08 19:06 42 *********************** 78 2018-05-08 19:07 41 ********************** 79 2018-05-08 19:08 42 *********************** 80 2018-05-08 19:09 42 *********************** 81 2018-05-08 19:10 42 *********************** 82 2018-05-08 19:11 41 ********************** 83 2018-05-08 19:12 41 ********************** 84 2018-05-08 19:13 42 *********************** ... ..( 6 skipped). .. *********************** 91 2018-05-08 19:20 42 *********************** 92 2018-05-08 19:21 41 ********************** 93 2018-05-08 19:22 42 *********************** 94 2018-05-08 19:23 41 ********************** ... ..( 8 skipped). .. ********************** 103 2018-05-08 19:32 41 ********************** 104 2018-05-08 19:33 40 ********************* 105 2018-05-08 19:34 41 ********************** ... ..( 20 skipped). .. ********************** 126 2018-05-08 19:55 41 ********************** 127 2018-05-08 19:56 40 ********************* ... ..( 3 skipped). .. ********************* 3 2018-05-08 20:00 40 ********************* 4 2018-05-08 20:01 ? - 5 2018-05-08 20:02 41 ********************** 6 2018-05-08 20:03 40 ********************* 7 2018-05-08 20:04 40 ********************* 8 2018-05-08 20:05 39 ******************** ... ..( 2 skipped). .. ******************** 11 2018-05-08 20:08 39 ******************** 12 2018-05-08 20:09 38 ******************* ... ..( 3 skipped). .. ******************* 16 2018-05-08 20:13 38 ******************* 17 2018-05-08 20:14 37 ****************** 18 2018-05-08 20:15 38 ******************* 19 2018-05-08 20:16 37 ****************** ... ..( 5 skipped). .. ****************** 25 2018-05-08 20:22 37 ****************** 26 2018-05-08 20:23 36 ***************** 27 2018-05-08 20:24 37 ****************** 28 2018-05-08 20:25 37 ****************** 29 2018-05-08 20:26 37 ****************** 30 2018-05-08 20:27 36 ***************** ... ..( 3 skipped). .. ***************** 34 2018-05-08 20:31 36 ***************** 35 2018-05-08 20:32 37 ****************** 36 2018-05-08 20:33 36 ***************** 37 2018-05-08 20:34 36 ***************** 38 2018-05-08 20:35 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 2072 Vendor specific