/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.14-desktop-1omv4002] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ADATA SU630 Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: V8X04c12 User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3, ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Sep 14 19:05:42 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1) seconds. Offline data collection capabilities: (0x59) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 7) minutes. Extended self-test routine recommended polling time: ( 23) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 050 - 0 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 9 Power_On_Hours -O--CK 100 100 000 - 236 12 Power_Cycle_Count -O--CK 100 100 000 - 221 161 Unknown_Attribute -O--CK 100 100 000 - 0 162 Unknown_Attribute -O--CK 100 100 000 - 2162 163 Unknown_Attribute -O--CK 100 100 000 - 3000 164 Unknown_Attribute -O--CK 100 100 000 - 4 166 Unknown_Attribute -O--CK 100 100 000 - 133 167 Unknown_Attribute -O--CK 100 100 050 - 0 168 Unknown_Attribute -O--CK 100 100 000 - 0 169 Unknown_Attribute -O--CK 100 100 000 - 100 171 Unknown_Attribute -O--CK 100 100 000 - 0 172 Unknown_Attribute -O--CK 100 100 000 - 0 174 Unknown_Attribute -O--CK 100 100 000 - 33 175 Program_Fail_Count_Chip -O--CK 100 100 000 - 0 181 Program_Fail_Cnt_Total -O---K 100 100 000 - 1786013 187 Reported_Uncorrect -O--CK 100 100 000 - 0 194 Temperature_Celsius -O---K 100 100 030 - 38 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 317 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 000 - 0 206 Unknown_SSD_Attribute -O--CK 100 100 000 - 0 207 Unknown_SSD_Attribute -O--CK 100 100 000 - 6 232 Available_Reservd_Space -O--CK 100 100 000 - 100 233 Media_Wearout_Indicator -O--CK 100 100 000 - 647 241 Total_LBAs_Written -O--CK 100 100 000 - 1176 242 Total_LBAs_Read -O--CK 100 100 000 - 538 249 Unknown_Attribute -O--CK 100 100 000 - 67 250 Read_Error_Retry_Rate -O--CK 100 100 000 - 1246 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 5 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 13 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [7] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 a0 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 a0 00 00 00 70 39 f0 40 08 00:39:46.750 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:46.525 FLUSH CACHE EXT 61 00 08 00 90 00 00 0f 86 78 50 40 08 00:39:46.525 WRITE FPDMA QUEUED 61 00 08 00 88 00 00 0f 86 78 28 40 08 00:39:46.525 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:46.524 FLUSH CACHE EXT Error 12 [6] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 78 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 78 00 00 00 70 39 f0 40 08 00:39:23.450 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:21.659 FLUSH CACHE EXT 61 00 08 00 68 00 00 0d c4 e5 f0 40 08 00:39:21.659 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:21.659 FLUSH CACHE EXT 61 00 20 00 58 00 00 0d c4 e5 d0 40 08 00:39:21.658 WRITE FPDMA QUEUED Error 11 [5] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 20 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 00 70 39 f0 40 08 00:39:16.586 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:10.652 FLUSH CACHE EXT 61 00 08 00 b0 00 00 0d c4 e5 c8 40 08 00:39:10.651 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:39:10.651 FLUSH CACHE EXT 61 00 38 00 a0 00 00 0d c4 e5 90 40 08 00:39:10.650 WRITE FPDMA QUEUED Error 10 [4] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 00 70 39 f0 40 08 00:39:05.742 READ FPDMA QUEUED 61 00 08 00 08 00 00 11 01 1a 38 40 08 00:39:05.276 WRITE FPDMA QUEUED 61 00 18 00 10 00 00 11 04 6a 98 40 08 00:39:05.276 WRITE FPDMA QUEUED 61 00 08 00 e8 00 00 11 00 34 c0 40 08 00:39:05.276 WRITE FPDMA QUEUED 61 00 08 00 e0 00 00 11 00 09 88 40 08 00:39:05.276 WRITE FPDMA QUEUED Error 9 [3] occurred at disk power-on lifetime: 165 hours (6 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 20 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 00 70 39 f0 40 08 00:36:37.451 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:36:37.281 FLUSH CACHE EXT 61 00 08 00 d0 00 00 0f 86 78 50 40 08 00:36:37.281 WRITE FPDMA QUEUED 61 00 08 00 c8 00 00 0f 86 78 28 40 08 00:36:37.281 WRITE FPDMA QUEUED 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:36:37.280 DATA SET MANAGEMENT Error 8 [2] occurred at disk power-on lifetime: 165 hours (6 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 18 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 18 00 00 00 70 39 f0 40 08 00:36:32.743 READ FPDMA QUEUED 60 00 08 00 10 00 00 0b c6 74 00 40 08 00:36:32.699 READ FPDMA QUEUED 60 00 08 00 08 00 00 0b c7 73 b0 40 08 00:36:32.699 READ FPDMA QUEUED 60 00 08 00 00 00 00 0b c7 73 18 40 08 00:36:32.698 READ FPDMA QUEUED 60 00 08 00 f0 00 00 0b c6 73 e8 40 08 00:36:32.697 READ FPDMA QUEUED Error 7 [1] occurred at disk power-on lifetime: 165 hours (6 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 78 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 78 00 00 00 70 39 f0 40 08 00:36:29.477 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 00:36:29.246 FLUSH CACHE EXT 61 00 08 00 68 00 00 0f 86 78 50 40 08 00:36:29.246 WRITE FPDMA QUEUED 61 00 08 00 60 00 00 0f 86 78 28 40 08 00:36:29.245 WRITE FPDMA QUEUED 06 00 01 00 01 00 00 00 00 00 00 a0 08 00:36:29.245 DATA SET MANAGEMENT Error 6 [0] occurred at disk power-on lifetime: 165 hours (6 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 80 00 00 00 70 39 f0 40 08 Error: UNC at LBA = 0x007039f0 = 7354864 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 80 00 00 00 70 39 f0 40 08 00:36:24.925 READ FPDMA QUEUED 60 01 00 00 f0 00 00 0f 88 47 28 40 08 00:36:24.877 READ FPDMA QUEUED 60 01 00 00 e8 00 00 0f 88 46 28 40 08 00:36:24.861 READ FPDMA QUEUED 60 01 00 00 e0 00 00 0f 88 45 28 40 08 00:36:24.854 READ FPDMA QUEUED 60 01 00 00 d8 00 00 0f 88 44 28 40 08 00:36:24.844 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 131 - # 2 Short offline Interrupted (host reset) 90% 127 - # 3 Short offline Interrupted (host reset) 90% 127 - # 4 Extended offline Interrupted (host reset) 90% 126 - # 5 Short offline Interrupted (host reset) 90% 124 - # 6 Short offline Interrupted (host reset) 90% 122 - # 7 Short offline Interrupted (host reset) 90% 115 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 0 (0x0000) Device State: Active (0) Current Temperature: 0 Celsius Power Cycle Min/Max Temperature: 28/28 Celsius Lifetime Min/Max Temperature: 0/36 Celsius Specified Max Operating Temperature: 100 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 0 minutes Temperature Logging Interval: 0 minutes Min/Max recommended Temperature: 0/100 Celsius Min/Max Temperature Limit: -10/125 Celsius Temperature History Size (Index): 128 (1) Index Estimated Time Temperature Celsius 2 2021-09-14 16:58 ? - ... ..(124 skipped). .. - 127 2021-09-14 19:03 ? - 0 2021-09-14 19:04 36 ***************** 1 2021-09-14 19:05 37 ****************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 221 --- Lifetime Power-On Resets 0x01 0x010 4 236 --- Power-on Hours 0x01 0x018 6 2466486867 --- Logical Sectors Written 0x01 0x020 6 21637580 --- Number of Write Commands 0x01 0x028 6 1128817209 --- Logical Sectors Read 0x01 0x030 6 19532316 --- Number of Read Commands 0x01 0x038 6 850036839 --- Date and Time TimeStamp 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 13 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 154743 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x000a 4 4 Device-to-host register FISes sent due to a COMRESET