Probe #bb8a8eac46 of MSI X99A RAIDER Desktop Computer (MS-7885)

Log: smartctl

/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.7-200.fc36.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: WD Blue / Red / Green SSDs Device Model: WDC WDS500G2B0A-00SM50 Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: X61130WD User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-4 T13/BSR INCITS 529 revision 5 SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jun 30 03:12:30 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 4 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 --- - 0 9 Power_On_Hours -O--CK 100 100 --- - 21581 12 Power_Cycle_Count -O--CK 100 100 --- - 17 165 Block_Erase_Count -O--CK 100 100 --- - 3535227066707 166 Minimum_PE_Cycles_TLC -O--CK 100 100 --- - 15 167 Max_Bad_Blocks_per_Die -O--CK 100 100 --- - 32 168 Maximum_PE_Cycles_TLC -O--CK 100 100 --- - 68 169 Total_Bad_Blocks -O--CK 100 100 --- - 326 170 Grown_Bad_Blocks -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 --- - 0 172 Erase_Fail_Count -O--CK 100 100 --- - 0 173 Average_PE_Cycles_TLC -O--CK 100 100 --- - 36 174 Unexpected_Power_Loss -O--CK 100 100 --- - 6 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 --- - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 065 045 --- - 35 (Min/Max 17/45) 199 UDMA_CRC_Error_Count -O--CK 100 100 --- - 0 230 Media_Wearout_Indicator -O--CK 100 100 --- - 0x0c60033c0c60 232 Available_Reservd_Space PO--CK 100 100 004 - 100 233 NAND_GB_Written_TLC -O--CK 100 100 --- - 18382 234 NAND_GB_Written_SLC -O--CK 100 100 --- - 78674 241 Host_Writes_GiB ----CK 253 253 --- - 57834 242 Host_Reads_GiB ----CK 253 253 --- - 15440 244 Temp_Throttle_Status -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 17 --- Lifetime Power-On Resets 0x01 0x010 4 0 --- Power-on Hours 0x01 0x018 6 121287695896 --- Logical Sectors Written 0x01 0x020 6 1918827156 --- Number of Write Commands 0x01 0x028 6 32380486867 --- Logical Sectors Read 0x01 0x030 6 1237624244 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 3 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 16 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.7-200.fc36.x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD100EFAX-68LHPN0 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: 83.H0A83 User Capacity: 10,000,831,348,736 bytes [10.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jun 30 03:12:30 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 164 (intermediate level without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 93) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: (1151) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance --S--- 129 129 054 - 112 3 Spin_Up_Time POS--- 153 153 024 - 434 (Average 428) 4 Start_Stop_Count -O--C- 100 100 000 - 17 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate -O-R-- 100 100 067 - 0 8 Seek_Time_Performance --S--- 128 128 020 - 18 9 Power_On_Hours -O--C- 097 097 000 - 21582 10 Spin_Retry_Count -O--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 17 22 Helium_Level PO---K 100 100 025 - 100 192 Power-Off_Retract_Count -O--CK 009 009 000 - 109612 193 Load_Cycle_Count -O--C- 009 009 000 - 109612 194 Temperature_Celsius -O---- 185 185 000 - 35 (Min/Max 15/47) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 255 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 5501 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x12 GPL R/O 1 SATA NCQ Non-Data log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL,SL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 256 Current Device Internal Status Data log 0x25 GPL R/O 256 Saved Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 24/46 Celsius Lifetime Min/Max Temperature: 15/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/65 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (92) Index Estimated Time Temperature Celsius 93 2023-06-30 01:05 35 **************** ... ..( 3 skipped). .. **************** 97 2023-06-30 01:09 35 **************** 98 2023-06-30 01:10 36 ***************** 99 2023-06-30 01:11 36 ***************** 100 2023-06-30 01:12 35 **************** ... ..( 4 skipped). .. **************** 105 2023-06-30 01:17 35 **************** 106 2023-06-30 01:18 36 ***************** ... ..( 3 skipped). .. ***************** 110 2023-06-30 01:22 36 ***************** 111 2023-06-30 01:23 35 **************** ... ..( 70 skipped). .. **************** 54 2023-06-30 02:34 35 **************** 55 2023-06-30 02:35 34 *************** 56 2023-06-30 02:36 34 *************** 57 2023-06-30 02:37 35 **************** ... ..( 6 skipped). .. **************** 64 2023-06-30 02:44 35 **************** 65 2023-06-30 02:45 34 *************** 66 2023-06-30 02:46 35 **************** ... ..( 7 skipped). .. **************** 74 2023-06-30 02:54 35 **************** 75 2023-06-30 02:55 34 *************** 76 2023-06-30 02:56 35 **************** ... ..( 6 skipped). .. **************** 83 2023-06-30 03:03 35 **************** 84 2023-06-30 03:04 34 *************** 85 2023-06-30 03:05 34 *************** 86 2023-06-30 03:06 34 *************** 87 2023-06-30 03:07 35 **************** ... ..( 4 skipped). .. **************** 92 2023-06-30 03:12 35 **************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 17 --- Lifetime Power-On Resets 0x01 0x010 4 21582 --- Power-on Hours 0x01 0x018 6 39074299400 --- Logical Sectors Written 0x01 0x020 6 29097511 --- Number of Write Commands 0x01 0x028 6 39089197630 --- Logical Sectors Read 0x01 0x030 6 153039937 --- Number of Read Commands 0x01 0x038 6 77695665550 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 12763 --- Spindle Motor Power-on Hours 0x03 0x010 4 12763 --- Head Flying Hours 0x03 0x018 4 109612 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 547420 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 34 N-- Average Short Term Temperature 0x05 0x018 1 37 N-- Average Long Term Temperature 0x05 0x020 1 47 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 44 N-- Highest Average Short Term Temperature 0x05 0x038 1 21 N-- Lowest Average Short Term Temperature 0x05 0x040 1 40 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 65 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 18 --- Number of Hardware Resets 0x06 0x010 4 116 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 18 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS


Hardware for Linux and BSD

GitHub