/dev/sda smartctl 7.2 2020-12-30 r5155 [i686-linux-5.10.0-9-686-pae] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 80GN Device Model: IC25N060ATMR04-0 Serial Number: -- Firmware Version: MO3OAD4A User Capacity: 60,011,642,880 bytes [60.0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-6 T13/1410D revision 3a Local Time is: Fri Nov 19 22:08:20 2021 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 53) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 105 105 040 - 5872 3 Spin_Up_Time POS--- 163 163 033 - 1 4 Start_Stop_Count -O--C- 098 098 000 - 4686 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 120 120 040 - 36 9 Power_On_Hours -O--C- 065 065 000 - 15503 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 4278 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 316 193 Load_Cycle_Count -O--C- 056 056 000 - 445121 194 Temperature_Celsius -O---- 144 144 000 - 38 (Min/Max 6/61) 196 Reallocated_Event_Count -O--CK 100 100 000 - 96 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 71 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 71 [2] occurred at disk power-on lifetime: 6588 hours (274 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 20 d7 4a 20 d7 47 e0 00 Error: UNC at LBA = 0x20d74a20d747 = 36109033723719 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 da d8 00 01 20 d7 4a 20 d7 47 e0 00 00:17:18.700 READ VERIFY SECTOR(S) 40 da d8 00 02 a9 62 f0 20 d7 49 e0 00 00:17:18.700 READ VERIFY SECTOR(S) c8 da d8 02 01 20 d7 47 a9 62 f0 e3 00 00:17:18.700 READ DMA 40 da d8 00 02 00 00 00 20 d7 47 e0 00 00:17:15.100 READ VERIFY SECTOR(S) c8 da d8 00 01 20 d7 4e 00 00 00 e0 00 00:17:15.100 READ DMA Error 70 [1] occurred at disk power-on lifetime: 15 hours (0 days + 15 hours) When the command that caused the error occurred, the device was in a vendor specific state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 04 e0 00 00 20 d7 47 c8 da Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 04 00 47 40 00 00 e0 20 d7 e0 da 41d+22:37:58.671 SMART [Reserved subcommand] b0 08 01 47 00 c8 20 d7 e0 00 00 e0 da 41d+22:37:58.671 SMART [Reserved subcommand] a0 00 08 46 47 40 20 d7 e0 20 d7 e0 da 41d+22:37:58.671 PACKET a0 00 08 f0 3f 40 a9 62 e0 20 d7 e0 da 41d+22:37:58.671 PACKET a0 00 01 5e f0 c8 20 d7 e3 a9 62 e0 da 41d+22:37:58.671 PACKET Error 69 [0] occurred at disk power-on lifetime: 55296 hours (2304 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- af 00 47 00 e0 00 c8 20 d7 a0 08 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 0f 00 3f 00 d7 90 40 00 20 e0 20 a1 00 08:38:39.360 [RESERVED] 0f 7e 00 d7 00 90 c8 20 00 e0 00 a1 00 3d+06:32:57.600 [RESERVED] 0f 00 5f 00 d7 90 40 00 20 e0 20 a1 00 08:38:39.360 [RESERVED] 0f 47 00 d7 00 90 c8 20 20 e0 00 a1 18 6d+09:06:53.056 [RESERVED] c8 da d8 00 01 20 d7 5e a9 62 f0 e3 00 08:38:39.360 READ DMA Error 68 [3] occurred at disk power-on lifetime: 6588 hours (274 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 20 d7 46 20 d7 47 e0 00 Error: UNC at LBA = 0x20d74620d747 = 36108966614855 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 40 da d8 00 08 20 d7 46 20 d7 47 e0 00 00:17:08.000 READ VERIFY SECTOR(S) 40 da d8 00 08 a9 62 f0 20 d7 3f e0 00 00:17:08.000 READ VERIFY SECTOR(S) c8 da d8 00 01 20 d7 5e a9 62 f0 e3 00 00:17:08.000 READ DMA 40 da d8 00 10 00 00 00 20 d7 4f e0 00 00:17:08.000 READ VERIFY SECTOR(S) c8 da d8 08 01 20 d7 47 00 00 00 e0 00 00:17:08.000 READ DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 15375 - Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum. SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported