/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.118-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K250 Device Model: Hitachi HTS542525K9SA00 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: BBFOC31P User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 3f SATA Version is: SATA 2.5, 1.5 Gb/s Local Time is: Mon Jul 11 15:23:59 2022 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 40) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 107) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 109 109 040 - 4393 3 Spin_Up_Time POS--- 250 250 033 - 1 4 Start_Stop_Count -O--C- 097 097 000 - 5245 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 132 132 040 - 34 9 Power_On_Hours -O--C- 063 063 000 - 16514 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 5098 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 299 193 Load_Cycle_Count -O--C- 096 096 000 - 49682 194 Temperature_Celsius -O---- 130 130 000 - 42 (Min/Max -4/62) 196 Reallocated_Event_Count -O--CK 100 100 000 - 5 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 692 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 692 [3] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 59 70 40 00 Error: IDNF at LBA = 0x1d1c5970 = 488397168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 08 00 00 1d 1c 59 70 40 00 00:00:36.800 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:36.800 SET FEATURES [Enable write cache] 60 00 01 00 01 00 00 00 00 00 01 a0 ff 00:00:36.700 READ FPDMA QUEUED 60 00 01 00 01 00 00 1d 1c 59 70 40 ff 00:00:36.700 READ FPDMA QUEUED 60 00 01 00 08 00 00 1d 1c 59 70 40 00 00:00:36.600 READ FPDMA QUEUED Error 691 [2] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 59 70 40 00 Error: IDNF at LBA = 0x1d1c5970 = 488397168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 08 00 00 1d 1c 59 70 40 00 00:00:36.600 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:36.600 SET FEATURES [Enable write cache] 60 00 01 00 01 00 00 00 00 00 01 a0 ff 00:00:36.500 READ FPDMA QUEUED 60 00 01 00 01 00 00 1d 1c 59 70 40 ff 00:00:36.500 READ FPDMA QUEUED 60 00 01 00 08 00 00 1d 1c 59 70 40 00 00:00:36.500 READ FPDMA QUEUED Error 690 [1] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 59 70 40 00 Error: IDNF at LBA = 0x1d1c5970 = 488397168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 08 00 00 1d 1c 59 70 40 00 00:00:36.500 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:36.500 SET FEATURES [Enable write cache] 60 00 01 00 01 00 00 00 00 00 01 a0 ff 00:00:36.400 READ FPDMA QUEUED 60 00 01 00 01 00 00 1d 1c 59 70 40 ff 00:00:36.400 READ FPDMA QUEUED 60 00 01 00 10 00 00 1d 1c 59 70 40 00 00:00:36.300 READ FPDMA QUEUED Error 689 [0] occurred at disk power-on lifetime: 6306 hours (262 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 01 00 00 1d 1c 59 70 40 00 Error: IDNF at LBA = 0x1d1c5970 = 488397168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 10 00 00 1d 1c 59 70 40 00 00:00:36.300 READ FPDMA QUEUED 61 00 01 00 08 00 00 03 0d e3 b0 40 00 00:00:36.300 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:36.300 SET FEATURES [Enable write cache] 60 00 01 00 01 00 00 00 00 00 01 a0 ff 00:00:36.200 READ FPDMA QUEUED 60 00 01 00 01 00 00 1d 1c 59 70 40 ff 00:00:36.200 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Invalid Self-test Log index = 0x2502 (reserved = 0x00) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 23/47 Celsius Lifetime Min/Max Temperature: -4/62 Celsius Specified Max Operating Temperature: 42 Celsius Under/Over Temperature Limit Count: 0/0 Unexpected SCT status 0x0000 (action_code=5, function_code=0) Read SCT Temperature History failed SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 65535+ Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS