Probe #adffeefeca of Acer Aspire 5250

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD5000BPVT-22HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon Mar 29 15:44:49 2021 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10980) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 110) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 874 3 Spin_Up_Time POS--K 174 173 021 - 2283 4 Start_Stop_Count -O--CK 059 059 000 - 41840 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 088 088 000 - 8896 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6297 191 G-Sense_Error_Rate -O--CK 001 001 000 - 7729 192 Power-Off_Retract_Count -O--CK 200 200 000 - 563 193 Load_Cycle_Count -O--CK 001 001 000 - 975786 194 Temperature_Celsius -O---K 112 098 000 - 35 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 878 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 878 [13] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:37.875 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:37.874 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:35.156 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:35.154 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:32.436 READ FPDMA QUEUED Error 877 [12] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:35.156 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:35.154 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:32.436 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:32.435 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:29.716 READ FPDMA QUEUED Error 876 [11] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:32.436 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:32.435 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:29.716 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:29.715 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:26.997 READ FPDMA QUEUED Error 875 [10] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:29.716 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:29.715 READ LOG EXT 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:26.997 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:26.996 READ LOG EXT 60 00 40 00 28 00 00 02 88 54 18 40 00 00:01:24.283 READ FPDMA QUEUED Error 874 [9] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 08 00 00 02 88 54 18 40 00 00:01:26.997 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 00:01:26.996 READ LOG EXT 60 00 40 00 28 00 00 02 88 54 18 40 00 00:01:24.283 READ FPDMA QUEUED 61 00 10 00 20 00 00 02 43 bf 70 40 00 00:01:24.267 WRITE FPDMA QUEUED 61 00 10 00 18 00 00 03 ac 35 60 40 00 00:01:24.267 WRITE FPDMA QUEUED Error 873 [8] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: UNC at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 28 00 00 02 88 54 18 40 00 00:01:24.283 READ FPDMA QUEUED 61 00 10 00 20 00 00 02 43 bf 70 40 00 00:01:24.267 WRITE FPDMA QUEUED 61 00 10 00 18 00 00 03 ac 35 60 40 00 00:01:24.267 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 0c bd b8 38 40 00 00:01:24.267 WRITE FPDMA QUEUED 60 00 80 00 08 00 00 01 ec 50 10 40 00 00:01:24.266 READ FPDMA QUEUED Error 872 [7] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: WP at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 58 00 00 0c bd b8 38 40 00 00:01:21.573 WRITE FPDMA QUEUED 61 00 08 00 50 00 00 0c bd b8 20 40 00 00:01:21.573 WRITE FPDMA QUEUED 61 00 08 00 48 00 00 03 ac 35 60 40 00 00:01:21.572 WRITE FPDMA QUEUED 61 00 08 00 40 00 00 0c bc d9 10 40 00 00:01:21.572 WRITE FPDMA QUEUED 61 00 08 00 38 00 00 01 e3 2c 68 40 00 00:01:21.572 WRITE FPDMA QUEUED Error 871 [6] occurred at disk power-on lifetime: 6561 hours (273 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 02 88 54 18 40 00 Error: WP at LBA = 0x02885418 = 42488856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 30 00 00 02 43 2a 10 40 00 00:01:18.842 WRITE FPDMA QUEUED 61 00 08 00 28 00 00 02 43 2a 20 40 00 00:01:18.841 WRITE FPDMA QUEUED 61 00 10 00 20 00 00 02 43 bf 60 40 00 00:01:18.839 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 03 ac 35 60 40 00 00:01:18.839 WRITE FPDMA QUEUED 60 00 80 00 10 00 00 01 ec 50 10 40 00 00:01:18.839 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 35/37 Celsius Lifetime Min/Max Temperature: 10/49 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (66) Index Estimated Time Temperature Celsius 67 2021-03-29 13:37 38 ******************* 68 2021-03-29 13:38 38 ******************* 69 2021-03-29 13:39 ? - 70 2021-03-29 13:40 37 ****************** 71 2021-03-29 13:41 37 ****************** 72 2021-03-29 13:42 ? - 73 2021-03-29 13:43 37 ****************** 74 2021-03-29 13:44 37 ****************** 75 2021-03-29 13:45 ? - 76 2021-03-29 13:46 37 ****************** 77 2021-03-29 13:47 36 ***************** 78 2021-03-29 13:48 ? - 79 2021-03-29 13:49 36 ***************** 80 2021-03-29 13:50 36 ***************** 81 2021-03-29 13:51 ? - 82 2021-03-29 13:52 36 ***************** 83 2021-03-29 13:53 36 ***************** 84 2021-03-29 13:54 ? - 85 2021-03-29 13:55 36 ***************** 86 2021-03-29 13:56 36 ***************** 87 2021-03-29 13:57 ? - 88 2021-03-29 13:58 36 ***************** 89 2021-03-29 13:59 36 ***************** 90 2021-03-29 14:00 ? - 91 2021-03-29 14:01 36 ***************** 92 2021-03-29 14:02 36 ***************** 93 2021-03-29 14:03 36 ***************** 94 2021-03-29 14:04 ? - 95 2021-03-29 14:05 36 ***************** 96 2021-03-29 14:06 36 ***************** 97 2021-03-29 14:07 ? - 98 2021-03-29 14:08 36 ***************** 99 2021-03-29 14:09 36 ***************** 100 2021-03-29 14:10 ? - 101 2021-03-29 14:11 36 ***************** 102 2021-03-29 14:12 36 ***************** 103 2021-03-29 14:13 36 ***************** 104 2021-03-29 14:14 35 **************** 105 2021-03-29 14:15 ? - 106 2021-03-29 14:16 35 **************** 107 2021-03-29 14:17 35 **************** 108 2021-03-29 14:18 ? - 109 2021-03-29 14:19 35 **************** ... ..( 3 skipped). .. **************** 113 2021-03-29 14:23 35 **************** 114 2021-03-29 14:24 36 ***************** 115 2021-03-29 14:25 36 ***************** 116 2021-03-29 14:26 36 ***************** 117 2021-03-29 14:27 37 ****************** ... ..( 6 skipped). .. ****************** 124 2021-03-29 14:34 37 ****************** 125 2021-03-29 14:35 38 ******************* ... ..( 4 skipped). .. ******************* 2 2021-03-29 14:40 38 ******************* 3 2021-03-29 14:41 39 ******************** ... ..( 8 skipped). .. ******************** 12 2021-03-29 14:50 39 ******************** 13 2021-03-29 14:51 40 ********************* 14 2021-03-29 14:52 40 ********************* 15 2021-03-29 14:53 39 ******************** 16 2021-03-29 14:54 39 ******************** 17 2021-03-29 14:55 38 ******************* 18 2021-03-29 14:56 ? - 19 2021-03-29 14:57 38 ******************* 20 2021-03-29 14:58 ? - 21 2021-03-29 14:59 38 ******************* 22 2021-03-29 15:00 ? - 23 2021-03-29 15:01 38 ******************* 24 2021-03-29 15:02 38 ******************* 25 2021-03-29 15:03 ? - 26 2021-03-29 15:04 37 ****************** ... ..( 2 skipped). .. ****************** 29 2021-03-29 15:07 37 ****************** 30 2021-03-29 15:08 ? - 31 2021-03-29 15:09 37 ****************** 32 2021-03-29 15:10 37 ****************** 33 2021-03-29 15:11 ? - 34 2021-03-29 15:12 37 ****************** ... ..( 9 skipped). .. ****************** 44 2021-03-29 15:22 37 ****************** 45 2021-03-29 15:23 ? - 46 2021-03-29 15:24 37 ****************** 47 2021-03-29 15:25 37 ****************** 48 2021-03-29 15:26 ? - 49 2021-03-29 15:27 37 ****************** 50 2021-03-29 15:28 37 ****************** 51 2021-03-29 15:29 36 ***************** ... ..( 3 skipped). .. ***************** 55 2021-03-29 15:33 36 ***************** 56 2021-03-29 15:34 ? - 57 2021-03-29 15:35 36 ***************** 58 2021-03-29 15:36 36 ***************** 59 2021-03-29 15:37 35 **************** 60 2021-03-29 15:38 35 **************** 61 2021-03-29 15:39 35 **************** 62 2021-03-29 15:40 ? - 63 2021-03-29 15:41 35 **************** 64 2021-03-29 15:42 35 **************** 65 2021-03-29 15:43 ? - 66 2021-03-29 15:44 35 **************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 816 Vendor specific


Hardware for Linux and BSD

GitHub