/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Barracuda ATA IV Device Model: ST320011A Serial Number: -- Firmware Version: 3.19 User Capacity: 20 019 314 176 bytes [20,0 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-5 (minor revision not indicated) Local Time is: Mon Mar 6 17:41:43 2017 +05 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 422) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 18) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 074 063 034 - 198523018 3 Spin_Up_Time PO---- 086 070 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4220 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 831502583 9 Power_On_Hours -O--CK 075 075 000 - 22375 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6847 194 Temperature_Celsius -O---K 039 056 000 - 39 195 Hardware_ECC_Recovered -O-RC- 074 063 000 - 198523018 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 193 000 - 22 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory not supported SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x80-0x9f SL R/W 16 Host vendor specific log 0xa0 SL VS 1 Device vendor specific log 0xa1 SL VS 20 Device vendor specific log 0xa2 SL VS 101 Device vendor specific log 0xa8 SL VS 20 Device vendor specific log 0xa9 SL VS 1 Device vendor specific log SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 ATA Error Count: 75 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 75 occurred at disk power-on lifetime: 22366 hours (931 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 00 00 00 f0 00 00:00:43.297 READ DMA c6 00 10 00 00 00 f0 00 00:00:43.297 SET MULTIPLE MODE 91 00 3f 00 00 00 ff 00 00:00:43.297 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 00 00 00 00 f0 00 00:00:43.297 RECALIBRATE [OBS-4] e3 00 00 3e 9f 54 b0 00 00:00:41.888 IDLE Error 74 occurred at disk power-on lifetime: 22366 hours (931 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 7f a7 54 f2 Error: ICRC, ABRT at LBA = 0x0254a77f = 39102335 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 7f a7 54 f2 00 00:00:41.318 READ DMA f9 00 00 7f a7 54 52 00 00:00:41.318 SET MAX ADDRESS [OBS-6] f8 00 00 7f a7 54 50 00 00:00:41.318 READ NATIVE MAX ADDRESS [OBS-ACS-3] f8 00 00 7f a7 54 50 00 00:00:41.318 READ NATIVE MAX ADDRESS [OBS-ACS-3] f8 00 00 7f a7 54 50 00 00:00:41.318 READ NATIVE MAX ADDRESS [OBS-ACS-3] Error 73 occurred at disk power-on lifetime: 22366 hours (931 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 00 00 00 f0 Error: ICRC, ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 01 00 00 00 f0 00 00:00:25.912 READ DMA 91 00 3f 00 00 00 ff 00 00:00:25.912 INITIALIZE DEVICE PARAMETERS [OBS-6] c6 00 10 00 00 00 f0 00 00:00:15.751 SET MULTIPLE MODE 91 00 3f 00 00 00 ff 00 00:00:15.751 INITIALIZE DEVICE PARAMETERS [OBS-6] 10 00 00 00 00 00 f0 00 00:00:15.751 RECALIBRATE [OBS-4] Error 72 occurred at disk power-on lifetime: 22365 hours (931 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 38 9f 54 f2 Error: ICRC, ABRT at LBA = 0x02549f38 = 39100216 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 07 38 9f 54 f2 00 00:56:59.235 READ DMA f8 00 00 00 00 00 f0 00 00:56:59.235 READ NATIVE MAX ADDRESS [OBS-ACS-3] ec 00 00 00 00 00 b0 02 00:56:59.232 IDENTIFY DEVICE ef 03 45 00 00 00 b0 02 00:56:59.230 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 f0 00 00:56:59.111 READ NATIVE MAX ADDRESS [OBS-ACS-3] Error 71 occurred at disk power-on lifetime: 22365 hours (931 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 38 9f 54 f2 Error: ICRC, ABRT at LBA = 0x02549f38 = 39100216 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 07 38 9f 54 f2 00 00:56:57.555 READ DMA c8 00 08 08 00 00 f0 00 00:56:57.541 READ DMA f8 00 00 00 00 00 f0 00 00:56:57.506 READ NATIVE MAX ADDRESS [OBS-ACS-3] ec 00 00 00 00 00 b0 02 00:56:57.502 IDENTIFY DEVICE ef 03 45 00 00 00 b0 02 00:56:57.500 SET FEATURES [Set transfer mode] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) not supported