/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD5000BPVT-22HXZT3 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 3 00:17:57 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11880) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 173 172 021 - 2350 4 Start_Stop_Count -O--CK 084 084 000 - 16086 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11574 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3046 191 G-Sense_Error_Rate -O--CK 001 001 000 - 17831 192 Power-Off_Retract_Count -O--CK 200 200 000 - 172 193 Load_Cycle_Count -O--CK 032 032 000 - 505042 194 Temperature_Celsius -O---K 108 081 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 192 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 192 [23] occurred at disk power-on lifetime: 10598 hours (441 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 50 00 00 00 2f 67 28 40 08 00:27:20.036 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:27:14.634 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:27:14.634 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:27:14.631 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 00:27:14.631 SET FEATURES [Set transfer mode] Error 191 [22] occurred at disk power-on lifetime: 10598 hours (441 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 48 00 00 00 2f 67 28 40 08 00:27:11.914 READ FPDMA QUEUED 60 01 00 00 40 00 00 00 2f 68 00 40 08 00:27:11.913 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:27:11.912 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:27:11.912 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:27:11.910 IDENTIFY DEVICE Error 190 [21] occurred at disk power-on lifetime: 10598 hours (441 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 00 2f 67 28 40 08 00:27:09.196 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 2f 68 00 40 08 00:27:09.196 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:27:09.196 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:27:09.196 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:27:09.193 IDENTIFY DEVICE Error 189 [20] occurred at disk power-on lifetime: 10598 hours (441 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 20 00 00 00 2f 67 00 40 08 00:27:06.489 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 2f 66 00 40 08 00:27:06.488 READ FPDMA QUEUED 60 01 00 00 10 00 00 00 2f 65 00 40 08 00:27:06.487 READ FPDMA QUEUED 60 01 00 00 08 00 00 00 2f 64 00 40 08 00:27:06.485 READ FPDMA QUEUED 60 01 00 00 00 00 00 00 2f 63 00 40 08 00:27:06.483 READ FPDMA QUEUED Error 188 [19] occurred at disk power-on lifetime: 10543 hours (439 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 2f 68 48 40 00 1d+12:25:37.379 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 2f 67 48 40 00 1d+12:25:37.379 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 2f 66 48 40 00 1d+12:25:37.379 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 2f 65 48 40 00 1d+12:25:37.379 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 2f 64 48 40 00 1d+12:25:37.378 READ FPDMA QUEUED Error 187 [18] occurred at disk power-on lifetime: 10543 hours (439 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 2f 68 48 40 00 1d+12:25:32.274 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 2f 67 48 40 00 1d+12:25:32.273 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 2f 66 48 40 00 1d+12:25:32.273 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 2f 65 48 40 00 1d+12:25:32.273 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 2f 64 48 40 00 1d+12:25:32.273 READ FPDMA QUEUED Error 186 [17] occurred at disk power-on lifetime: 10543 hours (439 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 2f 68 48 40 00 1d+12:25:26.202 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 2f 67 48 40 00 1d+12:25:26.201 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 2f 66 48 40 00 1d+12:25:26.201 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 2f 65 48 40 00 1d+12:25:26.201 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 2f 64 48 40 00 1d+12:25:26.201 READ FPDMA QUEUED Error 185 [16] occurred at disk power-on lifetime: 10543 hours (439 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 2f 67 28 40 00 Error: UNC at LBA = 0x002f6728 = 3106600 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 01 00 00 38 00 00 00 2f 68 48 40 00 1d+12:25:16.971 READ FPDMA QUEUED 60 01 00 00 30 00 00 00 2f 67 48 40 00 1d+12:25:16.971 READ FPDMA QUEUED 60 01 00 00 28 00 00 00 2f 66 48 40 00 1d+12:25:16.971 READ FPDMA QUEUED 60 01 00 00 20 00 00 00 2f 65 48 40 00 1d+12:25:16.970 READ FPDMA QUEUED 60 01 00 00 18 00 00 00 2f 64 48 40 00 1d+12:25:16.970 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 34/42 Celsius Lifetime Min/Max Temperature: 0/66 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (9) Index Estimated Time Temperature Celsius 10 2016-01-02 22:10 37 ****************** 11 2016-01-02 22:11 36 ***************** 12 2016-01-02 22:12 36 ***************** 13 2016-01-02 22:13 ? - 14 2016-01-02 22:14 36 ***************** 15 2016-01-02 22:15 36 ***************** 16 2016-01-02 22:16 36 ***************** 17 2016-01-02 22:17 37 ****************** 18 2016-01-02 22:18 38 ******************* 19 2016-01-02 22:19 39 ******************** 20 2016-01-02 22:20 39 ******************** 21 2016-01-02 22:21 40 ********************* ... ..( 4 skipped). .. ********************* 26 2016-01-02 22:26 40 ********************* 27 2016-01-02 22:27 41 ********************** ... ..( 19 skipped). .. ********************** 47 2016-01-02 22:47 41 ********************** 48 2016-01-02 22:48 40 ********************* ... ..( 4 skipped). .. ********************* 53 2016-01-02 22:53 40 ********************* 54 2016-01-02 22:54 39 ******************** 55 2016-01-02 22:55 39 ******************** 56 2016-01-02 22:56 39 ******************** 57 2016-01-02 22:57 40 ********************* ... ..( 22 skipped). .. ********************* 80 2016-01-02 23:20 40 ********************* 81 2016-01-02 23:21 39 ******************** ... ..( 8 skipped). .. ******************** 90 2016-01-02 23:30 39 ******************** 91 2016-01-02 23:31 40 ********************* 92 2016-01-02 23:32 39 ******************** ... ..( 18 skipped). .. ******************** 111 2016-01-02 23:51 39 ******************** 112 2016-01-02 23:52 ? - 113 2016-01-02 23:53 39 ******************** 114 2016-01-02 23:54 39 ******************** 115 2016-01-02 23:55 ? - 116 2016-01-02 23:56 39 ******************** ... ..( 4 skipped). .. ******************** 121 2016-01-03 00:01 39 ******************** 122 2016-01-03 00:02 40 ********************* ... ..( 2 skipped). .. ********************* 125 2016-01-03 00:05 40 ********************* 126 2016-01-03 00:06 39 ******************** 127 2016-01-03 00:07 39 ******************** 0 2016-01-03 00:08 40 ********************* 1 2016-01-03 00:09 40 ********************* 2 2016-01-03 00:10 39 ******************** ... ..( 6 skipped). .. ******************** 9 2016-01-03 00:17 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 10595 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 10989 Vendor specific