/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.18.16-un-def-alt1] (ALT Sisyphus 7.2-alt1) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: MN6OA5C0 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Aug 16 22:10:47 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18950) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 316) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 135 135 054 - 86 3 Spin_Up_Time POS--- 165 165 024 - 433 (Average 262) 4 Start_Stop_Count -O--C- 099 099 000 - 4161 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 135 135 020 - 26 9 Power_On_Hours -O--C- 096 096 000 - 28736 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 4121 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4171 193 Load_Cycle_Count -O--C- 097 097 000 - 4171 194 Temperature_Celsius -O---- 142 142 000 - 42 (Min/Max 19/48) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 14 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 1 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 14 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 14 [1] occurred at disk power-on lifetime: 6076 hours (253 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 56 fa 46 50 06 00 Error: ICRC, ABRT at LBA = 0x56fa4650 = 1459242576 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 01 d0 00 38 00 00 56 fa 45 00 40 08 02:33:38.580 WRITE FPDMA QUEUED 61 00 10 00 30 00 00 57 b5 3e 80 40 08 02:33:38.580 WRITE FPDMA QUEUED 61 00 10 00 28 00 00 57 b8 54 10 40 08 02:33:38.580 WRITE FPDMA QUEUED 61 00 10 00 20 00 00 57 b8 50 90 40 08 02:33:38.580 WRITE FPDMA QUEUED 61 00 08 00 18 00 00 57 b5 53 38 40 08 02:33:38.579 WRITE FPDMA QUEUED Error 13 [0] occurred at disk power-on lifetime: 556 hours (23 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 59 10 ed ff 09 00 Error: ICRC, ABRT at LBA = 0x5910edff = 1494281727 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 00 00 00 59 10 ed e0 40 08 00:21:52.110 READ FPDMA QUEUED 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:52.109 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:21:52.101 IDENTIFY DEVICE ef 00 03 00 46 e0 88 af 00 00 00 a0 08 00:21:52.093 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:21:52.093 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 12 [3] occurred at disk power-on lifetime: 556 hours (23 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 59 10 ed ff 09 00 Error: ICRC, ABRT at LBA = 0x5910edff = 1494281727 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 00 00 00 59 10 ed e0 40 08 00:21:51.613 READ FPDMA QUEUED 60 00 08 00 00 00 00 58 52 3b d8 40 08 00:21:51.602 READ FPDMA QUEUED ec 18 00 18 01 11 0f 20 00 00 00 00 08 00:21:51.578 IDENTIFY DEVICE 60 00 18 00 00 00 00 59 11 0f 20 40 08 00:21:51.571 READ FPDMA QUEUED 60 00 10 00 08 00 00 59 10 ed 98 40 08 00:21:51.564 READ FPDMA QUEUED Error 11 [2] occurred at disk power-on lifetime: 555 hours (23 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 04 95 c3 cd 04 00 Error: ICRC, ABRT at LBA = 0x0495c3cd = 76923853 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 3c 01 00 00 00 04 95 c3 92 40 00 00:01:40.673 READ FPDMA QUEUED 2f 3c 00 01 01 00 00 00 00 00 10 00 04 00:01:39.682 READ LOG EXT 2f 3c 00 01 01 00 00 00 00 00 10 00 00 00:01:39.682 READ LOG EXT 60 00 3c 01 00 00 00 04 95 c3 92 40 00 00:01:39.680 READ FPDMA QUEUED 2f 3c 00 01 01 00 00 00 00 00 10 00 04 00:01:38.680 READ LOG EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8677 - # 2 Extended offline Aborted by host 90% 8677 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 30/42 Celsius Lifetime Min/Max Temperature: 19/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (44) Index Estimated Time Temperature Celsius 45 2022-08-16 20:03 38 ******************* 46 2022-08-16 20:04 39 ******************** ... ..( 6 skipped). .. ******************** 53 2022-08-16 20:11 39 ******************** 54 2022-08-16 20:12 40 ********************* ... ..( 12 skipped). .. ********************* 67 2022-08-16 20:25 40 ********************* 68 2022-08-16 20:26 41 ********************** 69 2022-08-16 20:27 40 ********************* 70 2022-08-16 20:28 41 ********************** ... ..( 20 skipped). .. ********************** 91 2022-08-16 20:49 41 ********************** 92 2022-08-16 20:50 42 *********************** 93 2022-08-16 20:51 41 ********************** 94 2022-08-16 20:52 41 ********************** 95 2022-08-16 20:53 42 *********************** 96 2022-08-16 20:54 41 ********************** 97 2022-08-16 20:55 42 *********************** 98 2022-08-16 20:56 42 *********************** 99 2022-08-16 20:57 41 ********************** 100 2022-08-16 20:58 41 ********************** 101 2022-08-16 20:59 42 *********************** ... ..( 18 skipped). .. *********************** 120 2022-08-16 21:18 42 *********************** 121 2022-08-16 21:19 41 ********************** 122 2022-08-16 21:20 42 *********************** 123 2022-08-16 21:21 42 *********************** 124 2022-08-16 21:22 41 ********************** 125 2022-08-16 21:23 42 *********************** 126 2022-08-16 21:24 41 ********************** 127 2022-08-16 21:25 42 *********************** 0 2022-08-16 21:26 42 *********************** 1 2022-08-16 21:27 42 *********************** 2 2022-08-16 21:28 41 ********************** 3 2022-08-16 21:29 42 *********************** 4 2022-08-16 21:30 41 ********************** 5 2022-08-16 21:31 41 ********************** 6 2022-08-16 21:32 42 *********************** 7 2022-08-16 21:33 42 *********************** 8 2022-08-16 21:34 41 ********************** 9 2022-08-16 21:35 42 *********************** 10 2022-08-16 21:36 41 ********************** ... ..( 2 skipped). .. ********************** 13 2022-08-16 21:39 41 ********************** 14 2022-08-16 21:40 42 *********************** 15 2022-08-16 21:41 41 ********************** 16 2022-08-16 21:42 42 *********************** 17 2022-08-16 21:43 42 *********************** 18 2022-08-16 21:44 41 ********************** 19 2022-08-16 21:45 42 *********************** 20 2022-08-16 21:46 42 *********************** 21 2022-08-16 21:47 41 ********************** ... ..( 3 skipped). .. ********************** 25 2022-08-16 21:51 41 ********************** 26 2022-08-16 21:52 42 *********************** 27 2022-08-16 21:53 41 ********************** ... ..( 2 skipped). .. ********************** 30 2022-08-16 21:56 41 ********************** 31 2022-08-16 21:57 42 *********************** 32 2022-08-16 21:58 41 ********************** ... ..( 8 skipped). .. ********************** 41 2022-08-16 22:07 41 ********************** 42 2022-08-16 22:08 42 *********************** 43 2022-08-16 22:09 41 ********************** 44 2022-08-16 22:10 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 4121 --- Lifetime Power-On Resets 0x01 0x010 4 28736 --- Power-on Hours 0x01 0x018 6 75284064391 --- Logical Sectors Written 0x01 0x020 6 460816569 --- Number of Write Commands 0x01 0x028 6 477056881911 --- Logical Sectors Read 0x01 0x030 6 1942203691 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 28719 --- Spindle Motor Power-on Hours 0x03 0x010 4 28719 --- Head Flying Hours 0x03 0x018 4 4171 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 17 --- Read Recovery Attempts 0x03 0x030 4 25 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 54 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 41 --- Current Temperature 0x05 0x010 1 39 N-- Average Short Term Temperature 0x05 0x018 1 40 N-- Average Long Term Temperature 0x05 0x020 1 48 --- Highest Temperature 0x05 0x028 1 19 --- Lowest Temperature 0x05 0x030 1 44 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 40 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 56270 --- Number of Hardware Resets 0x06 0x010 4 29721 --- Number of ASR Events 0x06 0x018 4 14 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.18.16-un-def-alt1] (ALT Sisyphus 7.2-alt1) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD60EZRZ-22GZ5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 6,001,175,126,016 bytes [6.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5700 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Aug 16 22:10:49 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3584) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 689) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 198 197 021 - 9100 4 Start_Stop_Count -O--CK 100 100 000 - 367 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5209 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 357 192 Power-Off_Retract_Count -O--CK 200 200 000 - 32 193 Load_Cycle_Count -O--CK 194 194 000 - 20595 194 Temperature_Celsius -O---K 111 106 000 - 41 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 54 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 29/41 Celsius Lifetime Min/Max Temperature: 21/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (355) Index Estimated Time Temperature Celsius 356 2022-08-16 14:13 37 ****************** ... ..( 39 skipped). .. ****************** 396 2022-08-16 14:53 37 ****************** 397 2022-08-16 14:54 ? - 398 2022-08-16 14:55 29 ********** 399 2022-08-16 14:56 30 *********** ... ..( 2 skipped). .. *********** 402 2022-08-16 14:59 30 *********** 403 2022-08-16 15:00 31 ************ 404 2022-08-16 15:01 31 ************ 405 2022-08-16 15:02 31 ************ 406 2022-08-16 15:03 32 ************* 407 2022-08-16 15:04 32 ************* 408 2022-08-16 15:05 32 ************* 409 2022-08-16 15:06 33 ************** ... ..( 2 skipped). .. ************** 412 2022-08-16 15:09 33 ************** 413 2022-08-16 15:10 34 *************** ... ..( 2 skipped). .. *************** 416 2022-08-16 15:13 34 *************** 417 2022-08-16 15:14 35 **************** ... ..( 3 skipped). .. **************** 421 2022-08-16 15:18 35 **************** 422 2022-08-16 15:19 36 ***************** ... ..( 4 skipped). .. ***************** 427 2022-08-16 15:24 36 ***************** 428 2022-08-16 15:25 37 ****************** ... ..( 5 skipped). .. ****************** 434 2022-08-16 15:31 37 ****************** 435 2022-08-16 15:32 38 ******************* ... ..( 8 skipped). .. ******************* 444 2022-08-16 15:41 38 ******************* 445 2022-08-16 15:42 39 ******************** ... ..( 12 skipped). .. ******************** 458 2022-08-16 15:55 39 ******************** 459 2022-08-16 15:56 40 ********************* ... ..( 34 skipped). .. ********************* 16 2022-08-16 16:31 40 ********************* 17 2022-08-16 16:32 41 ********************** ... ..( 59 skipped). .. ********************** 77 2022-08-16 17:32 41 ********************** 78 2022-08-16 17:33 37 ****************** ... ..( 25 skipped). .. ****************** 104 2022-08-16 17:59 37 ****************** 105 2022-08-16 18:00 38 ******************* ... ..( 17 skipped). .. ******************* 123 2022-08-16 18:18 38 ******************* 124 2022-08-16 18:19 37 ****************** ... ..( 36 skipped). .. ****************** 161 2022-08-16 18:56 37 ****************** 162 2022-08-16 18:57 38 ******************* ... ..( 3 skipped). .. ******************* 166 2022-08-16 19:01 38 ******************* 167 2022-08-16 19:02 37 ****************** ... ..( 62 skipped). .. ****************** 230 2022-08-16 20:05 37 ****************** 231 2022-08-16 20:06 36 ***************** ... ..( 93 skipped). .. ***************** 325 2022-08-16 21:40 36 ***************** 326 2022-08-16 21:41 37 ****************** ... ..( 28 skipped). .. ****************** 355 2022-08-16 22:10 37 ****************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 9465 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.18.16-un-def-alt1] (ALT Sisyphus 7.2-alt1) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST1000DL004 HD105SI Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 1AJ10001 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Tue Aug 16 22:10:49 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12300) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 205) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 27 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 074 051 025 - 7951 4 Start_Stop_Count -O--CK 096 096 000 - 4633 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 21776 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 252 252 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4272 191 G-Sense_Error_Rate -O---K 029 029 000 - 718266 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 061 054 000 - 39 (Min/Max -3/46) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 100 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 1 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 24176 223 Load_Retry_Count -O--CK 252 252 000 - 0 225 Load_Cycle_Count -O--CK 100 100 000 - 4775 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 22 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 22 [5] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.285 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:00.285 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.285 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.285 IDENTIFY DEVICE Error 21 [4] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.283 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:00.283 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.283 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.283 IDENTIFY DEVICE Error 20 [3] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 00 00 08 00 00 49 48 98 00 40 08 00:00:00.282 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 b9 08 40 08 00:00:00.282 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e 84 99 e0 40 08 00:00:00.282 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e 84 98 e0 40 08 00:00:00.282 READ FPDMA QUEUED Error 19 [2] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.241 READ FPDMA QUEUED 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.271 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:00.271 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.271 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.271 IDENTIFY DEVICE Error 18 [1] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.241 READ FPDMA QUEUED 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.269 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:00.269 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:00:00.269 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:00.269 IDENTIFY DEVICE Error 17 [0] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.227 READ FPDMA QUEUED 60 00 00 00 08 00 00 49 48 98 00 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 b9 08 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e 84 99 e0 40 08 00:00:00.267 READ FPDMA QUEUED 60 00 00 01 00 00 00 1e 84 98 e0 40 08 00:00:00.267 READ FPDMA QUEUED Error 16 [7] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 49 48 98 00 40 08 00:00:00.225 READ FPDMA QUEUED 60 00 10 00 08 00 00 49 48 98 00 40 08 00:00:00.241 READ FPDMA QUEUED 60 00 10 00 08 00 00 1e 84 b9 08 40 08 00:00:00.241 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 99 58 40 08 00:00:00.241 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 99 50 40 08 00:00:00.241 READ FPDMA QUEUED Error 15 [6] occurred at disk power-on lifetime: 12068 hours (502 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 49 48 98 00 40 00 Error: UNC at LBA = 0x49489800 = 1229494272 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 49 48 98 00 40 08 00:00:00.222 READ FPDMA QUEUED 60 00 00 00 08 00 00 49 48 98 00 40 08 00:00:00.225 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 b9 08 40 08 00:00:00.225 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 99 58 40 08 00:00:00.225 READ FPDMA QUEUED 60 00 00 00 08 00 00 1e 84 99 50 40 08 00:00:00.225 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1576 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 28/39 Celsius Lifetime Min/Max Temperature: 1/65 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (46) Index Estimated Time Temperature Celsius 47 2022-08-16 11:35 37 ****************** ... ..( 4 skipped). .. ****************** 52 2022-08-16 12:00 37 ****************** 53 2022-08-16 12:05 36 ***************** ... ..( 30 skipped). .. ***************** 84 2022-08-16 14:40 36 ***************** 85 2022-08-16 14:45 35 **************** ... ..( 52 skipped). .. **************** 10 2022-08-16 19:10 35 **************** 11 2022-08-16 19:15 36 ***************** 12 2022-08-16 19:20 35 **************** 13 2022-08-16 19:25 36 ***************** 14 2022-08-16 19:30 36 ***************** 15 2022-08-16 19:35 36 ***************** 16 2022-08-16 19:40 28 ********* 17 2022-08-16 19:45 30 *********** 18 2022-08-16 19:50 32 ************* 19 2022-08-16 19:55 33 ************** 20 2022-08-16 20:00 34 *************** 21 2022-08-16 20:05 35 **************** 22 2022-08-16 20:10 36 ***************** 23 2022-08-16 20:15 36 ***************** 24 2022-08-16 20:20 37 ****************** 25 2022-08-16 20:25 37 ****************** 26 2022-08-16 20:30 38 ******************* ... ..( 2 skipped). .. ******************* 29 2022-08-16 20:45 38 ******************* 30 2022-08-16 20:50 39 ******************** ... ..( 15 skipped). .. ******************** 46 2022-08-16 22:10 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific /dev/sdd smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.18.16-un-def-alt1] (ALT Sisyphus 7.2-alt1) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Phison Driven SSDs Device Model: SSD Smartbuy 120GB Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: SBFM21.0 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-4 (minor revision not indicated) SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Aug 16 22:10:50 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (65535) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. Conveyance self-test routine recommended polling time: ( 6) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 1 9 Power_On_Hours -O--C- 100 100 000 - 11259 12 Power_Cycle_Count -O--C- 100 100 000 - 884 168 SATA_Phy_Error_Count -O--C- 100 100 000 - 0 170 Bad_Blk_Ct_Erl/Lat PO---- 074 074 010 - 0/114 173 MaxAvgErase_Ct -O--C- 100 100 000 - 34 (Average 21) 192 Unsafe_Shutdown_Count -O--C- 100 100 000 - 357 194 Temperature_Celsius PO---K 067 067 000 - 33 (Min/Max 33/33) 218 CRC_Error_Count PO-R-- 100 100 050 - 0 231 SSD_Life_Left PO--C- 100 100 000 - 99 241 Lifetime_Writes_GiB -O--C- 100 100 000 - 1735 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 884 --- Lifetime Power-On Resets 0x01 0x010 4 11259 --- Power-on Hours 0x01 0x018 6 3639885484 --- Logical Sectors Written 0x01 0x028 6 6335093437 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 1 --- Number of Reported Uncorrectable Errors 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 33 --- Current Temperature 0x05 0x020 1 33 --- Highest Temperature 0x05 0x028 1 33 --- Lowest Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 5 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 5 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC