/dev/sda smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-84-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST2000DM008-2FR102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Wed Oct 4 13:31:21 2023 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 198) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x30a5) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 084 064 006 - 225188863 3 Spin_Up_Time PO---- 098 098 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 343 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 090 060 045 - 983868452 9 Power_On_Hours -O--CK 090 090 000 - 9048 (44 48 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 343 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 131074 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 061 055 040 - 39 (Min/Max 22/41) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 324 193 Load_Cycle_Count -O--CK 095 095 000 - 10613 194 Temperature_Celsius -O---K 039 045 000 - 39 (0 13 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 084 064 000 - 225188863 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 8803 (152 123 0) 241 Total_LBAs_Written ------ 100 253 000 - 11913139200 242 Total_LBAs_Read ------ 100 253 000 - 9002292054 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 8160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 9048 Device vendor specific log 0xbd GPL VS 8 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 16 Device vendor specific log 0xc3 GPL,SL VS 8 Device vendor specific log 0xc4 GPL,SL VS 24 Device vendor specific log 0xd1 GPL VS 264 Device vendor specific log 0xd3 GPL VS 1920 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 212 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 22/41 Celsius Lifetime Min/Max Temperature: 13/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (75) Index Estimated Time Temperature Celsius 76 2023-09-29 08:04 37 ****************** 77 2023-09-29 09:03 37 ****************** 78 2023-09-29 10:02 37 ****************** 79 2023-09-29 11:01 38 ******************* 80 2023-09-29 12:00 38 ******************* 81 2023-09-29 12:59 37 ****************** 82 2023-09-29 13:58 ? - 83 2023-09-29 14:57 22 *** 84 2023-09-29 15:56 ? - 85 2023-09-29 16:55 39 ******************** ... ..( 2 skipped). .. ******************** 88 2023-09-29 19:52 39 ******************** 89 2023-09-29 20:51 38 ******************* 90 2023-09-29 21:50 39 ******************** 91 2023-09-29 22:49 38 ******************* 92 2023-09-29 23:48 ? - 93 2023-09-30 00:47 20 * 94 2023-09-30 01:46 38 ******************* 95 2023-09-30 02:45 39 ******************** 96 2023-09-30 03:44 38 ******************* 97 2023-09-30 04:43 37 ****************** 98 2023-09-30 05:42 37 ****************** 99 2023-09-30 06:41 37 ****************** 100 2023-09-30 07:40 38 ******************* ... ..( 4 skipped). .. ******************* 105 2023-09-30 12:35 38 ******************* 106 2023-09-30 13:34 37 ****************** ... ..( 4 skipped). .. ****************** 111 2023-09-30 18:29 37 ****************** 112 2023-09-30 19:28 36 ***************** ... ..( 12 skipped). .. ***************** 125 2023-10-01 08:15 36 ***************** 126 2023-10-01 09:14 37 ****************** ... ..( 4 skipped). .. ****************** 3 2023-10-01 14:09 37 ****************** 4 2023-10-01 15:08 36 ***************** ... ..( 6 skipped). .. ***************** 11 2023-10-01 22:01 36 ***************** 12 2023-10-01 23:00 35 **************** ... ..( 5 skipped). .. **************** 18 2023-10-02 04:54 35 **************** 19 2023-10-02 05:53 36 ***************** 20 2023-10-02 06:52 36 ***************** 21 2023-10-02 07:51 37 ****************** ... ..( 7 skipped). .. ****************** 29 2023-10-02 15:43 37 ****************** 30 2023-10-02 16:42 36 ***************** 31 2023-10-02 17:41 36 ***************** 32 2023-10-02 18:40 37 ****************** 33 2023-10-02 19:39 36 ***************** ... ..( 2 skipped). .. ***************** 36 2023-10-02 22:36 36 ***************** 37 2023-10-02 23:35 37 ****************** 38 2023-10-03 00:34 36 ***************** 39 2023-10-03 01:33 37 ****************** 40 2023-10-03 02:32 37 ****************** 41 2023-10-03 03:31 38 ******************* 42 2023-10-03 04:30 40 ********************* 43 2023-10-03 05:29 41 ********************** 44 2023-10-03 06:28 40 ********************* 45 2023-10-03 07:27 39 ******************** 46 2023-10-03 08:26 39 ******************** 47 2023-10-03 09:25 39 ******************** 48 2023-10-03 10:24 38 ******************* 49 2023-10-03 11:23 38 ******************* 50 2023-10-03 12:22 38 ******************* 51 2023-10-03 13:21 40 ********************* 52 2023-10-03 14:20 41 ********************** 53 2023-10-03 15:19 39 ******************** 54 2023-10-03 16:18 38 ******************* 55 2023-10-03 17:17 38 ******************* 56 2023-10-03 18:16 38 ******************* 57 2023-10-03 19:15 39 ******************** 58 2023-10-03 20:14 41 ********************** 59 2023-10-03 21:13 39 ******************** 60 2023-10-03 22:12 38 ******************* ... ..( 3 skipped). .. ******************* 64 2023-10-04 02:08 38 ******************* 65 2023-10-04 03:07 39 ******************** 66 2023-10-04 04:06 38 ******************* 67 2023-10-04 05:05 39 ******************** 68 2023-10-04 06:04 39 ******************** 69 2023-10-04 07:03 ? - 70 2023-10-04 08:02 22 *** 71 2023-10-04 09:01 38 ******************* 72 2023-10-04 10:00 41 ********************** 73 2023-10-04 10:59 40 ********************* 74 2023-10-04 11:58 40 ********************* 75 2023-10-04 12:57 40 ********************* SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 343 --- Lifetime Power-On Resets 0x01 0x010 4 9048 --- Power-on Hours 0x01 0x018 6 11910736727 --- Logical Sectors Written 0x01 0x020 6 150298766 --- Number of Write Commands 0x01 0x028 6 8992014751 --- Logical Sectors Read 0x01 0x030 6 78848930 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 9021 --- Spindle Motor Power-on Hours 0x03 0x010 4 8806 --- Head Flying Hours 0x03 0x018 4 10613 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 324 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 2 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 39 --- Current Temperature 0x05 0x010 1 38 --- Average Short Term Temperature 0x05 0x018 1 38 --- Average Long Term Temperature 0x05 0x020 1 45 --- Highest Temperature 0x05 0x028 1 0 --- Lowest Temperature 0x05 0x030 1 44 --- Highest Average Short Term Temperature 0x05 0x038 1 28 --- Lowest Average Short Term Temperature 0x05 0x040 1 40 --- Highest Average Long Term Temperature 0x05 0x048 1 31 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 1190 --- Number of Hardware Resets 0x06 0x010 4 705 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.15.0-84-generic] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Elements / My Passport (USB, AF) Device Model: WDC WD10JMVW-11S5XS0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Wed Oct 4 13:31:22 2023 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (18000) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 196) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x70b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 196 195 051 - 1724 3 Spin_Up_Time POS--K 182 174 021 - 1900 4 Start_Stop_Count -O--CK 097 097 000 - 3107 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 085 085 000 - 11072 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 762 192 Power-Off_Retract_Count -O--CK 200 200 000 - 431 193 Load_Cycle_Count -O--CK 197 197 000 - 11196 194 Temperature_Celsius -O---K 107 099 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1724 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1724 [19] occurred at disk power-on lifetime: 3290 hours (137 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:10:11.176 READ DMA EXT 35 00 00 00 08 00 00 00 60 39 98 40 00 00:10:11.176 WRITE DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:10:11.176 IDLE IMMEDIATE e1 00 00 00 02 00 00 00 00 00 00 00 00 00:10:10.893 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 00 00:10:10.892 IDENTIFY DEVICE Error 1723 [18] occurred at disk power-on lifetime: 3290 hours (137 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:09:48.043 READ DMA EXT 35 00 00 00 08 00 00 00 60 09 20 40 00 00:09:48.043 WRITE DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:09:48.042 IDLE IMMEDIATE e1 00 00 00 02 00 00 00 00 00 00 00 00 00:09:47.767 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 00 00:09:47.766 IDENTIFY DEVICE Error 1722 [17] occurred at disk power-on lifetime: 3290 hours (137 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:09:24.942 READ DMA EXT 35 00 00 00 18 00 00 00 00 ce e0 40 00 00:09:24.942 WRITE DMA EXT b0 00 d0 00 00 00 00 00 c2 4f 00 00 00 00:09:24.925 SMART READ DATA 35 00 00 00 08 00 00 00 60 09 10 40 00 00:09:24.916 WRITE DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:09:24.916 IDLE IMMEDIATE Error 1721 [16] occurred at disk power-on lifetime: 3289 hours (137 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:09:01.782 READ DMA EXT 35 00 00 00 30 00 00 00 00 ce 40 40 00 00:09:01.782 WRITE DMA EXT 35 00 00 00 3d 00 00 00 00 12 44 40 00 00:09:01.782 WRITE DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:09:01.781 IDLE IMMEDIATE e1 00 00 00 02 00 00 00 00 00 00 00 00 00:09:01.495 IDLE IMMEDIATE Error 1720 [15] occurred at disk power-on lifetime: 3289 hours (137 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:08:38.656 READ DMA EXT 35 00 00 00 08 00 00 00 00 ce a0 40 00 00:08:38.656 WRITE DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:08:38.655 IDLE IMMEDIATE e1 00 00 00 02 00 00 00 00 00 00 00 00 00:08:38.379 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 00 00:08:38.378 IDENTIFY DEVICE Error 1719 [14] occurred at disk power-on lifetime: 3289 hours (137 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:08:15.534 READ DMA EXT e1 00 00 00 0f 00 00 00 00 00 00 00 00 00:08:15.533 IDLE IMMEDIATE e1 00 00 00 02 00 00 00 00 00 00 00 00 00:08:15.243 IDLE IMMEDIATE ec 00 00 00 01 00 00 00 00 00 00 00 00 00:08:15.242 IDENTIFY DEVICE 35 00 00 00 08 00 00 00 00 ce a0 40 00 00:07:55.086 WRITE DMA EXT Error 1718 [13] occurred at disk power-on lifetime: 3289 hours (137 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:07:52.399 READ DMA EXT 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:07:49.689 READ DMA EXT 35 00 00 00 08 00 00 00 5e 07 f0 40 00 00:07:48.373 WRITE DMA EXT 35 00 00 00 08 00 00 00 5e 08 08 40 00 00:07:48.372 WRITE DMA EXT 35 00 00 00 38 00 00 00 5e f3 c8 40 00 00:07:48.364 WRITE DMA EXT Error 1717 [12] occurred at disk power-on lifetime: 3289 hours (137 days + 1 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 00 32 47 d8 40 00 Error: UNC 8 sectors at LBA = 0x003247d8 = 3295192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 00 32 47 d8 40 00 00:07:49.689 READ DMA EXT 35 00 00 00 08 00 00 00 5e 07 f0 40 00 00:07:48.373 WRITE DMA EXT 35 00 00 00 08 00 00 00 5e 08 08 40 00 00:07:48.372 WRITE DMA EXT 35 00 00 00 38 00 00 00 5e f3 c8 40 00 00:07:48.364 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 ce f8 40 00 00:07:48.043 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 24/43 Celsius Lifetime Min/Max Temperature: 13/48 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (68) Index Estimated Time Temperature Celsius 69 2023-10-04 11:24 41 ********************** ... ..( 23 skipped). .. ********************** 93 2023-10-04 11:48 41 ********************** 94 2023-10-04 11:49 40 ********************* ... ..(101 skipped). .. ********************* 68 2023-10-04 13:31 40 ********************* SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 16 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 431878 Vendor specific