/dev/sda smartctl 7.1 2020-08-23 r5080 [x86_64-linux-6.4.3-1.el8.elrepo.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD10JPVX-00JC3T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Jul 13 21:25:32 2023 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17340) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 194) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 186 181 021 - 1700 4 Start_Stop_Count -O--CK 095 095 000 - 5009 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 071 071 000 - 21579 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4404 192 Power-Off_Retract_Count -O--CK 200 200 000 - 262 193 Load_Cycle_Count -O--CK 001 001 000 - 1139465 194 Temperature_Celsius -O---K 114 101 000 - 33 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 21500 - # 2 Extended offline Aborted by host 90% 21500 - # 3 Extended offline Completed without error 00% 21500 - # 4 Short offline Completed without error 00% 21497 - # 5 Short offline Completed without error 00% 20971 - # 6 Short offline Completed without error 00% 20970 - # 7 Short offline Completed without error 00% 20869 - # 8 Short offline Aborted by host 90% 20335 - # 9 Short offline Completed without error 00% 18728 - #10 Short offline Aborted by host 50% 18020 - #11 Short offline Aborted by host 90% 14331 - #12 Short offline Aborted by host 90% 11193 - #13 Short offline Aborted by host 90% 9205 - #14 Short offline Aborted by host 90% 9205 - #15 Short offline Aborted by host 90% 64 - #16 Short offline Aborted by host 90% 63 - #17 Short offline Completed without error 00% 63 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 33 Celsius Power Cycle Min/Max Temperature: 29/35 Celsius Lifetime Min/Max Temperature: 0/46 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (54) Index Estimated Time Temperature Celsius 55 2023-07-13 19:18 32 ************* ... ..( 15 skipped). .. ************* 71 2023-07-13 19:34 32 ************* 72 2023-07-13 19:35 33 ************** ... ..( 17 skipped). .. ************** 90 2023-07-13 19:53 33 ************** 91 2023-07-13 19:54 34 *************** ... ..( 15 skipped). .. *************** 107 2023-07-13 20:10 34 *************** 108 2023-07-13 20:11 35 **************** 109 2023-07-13 20:12 34 *************** 110 2023-07-13 20:13 35 **************** ... ..( 49 skipped). .. **************** 32 2023-07-13 21:03 35 **************** 33 2023-07-13 21:04 34 *************** ... ..( 15 skipped). .. *************** 49 2023-07-13 21:20 34 *************** 50 2023-07-13 21:21 33 ************** ... ..( 3 skipped). .. ************** 54 2023-07-13 21:25 33 ************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 110 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 9741 Vendor specific /dev/sdb smartctl 7.1 2020-08-23 r5080 [x86_64-linux-6.4.3-1.el8.elrepo.x86_64] (local build) Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Intel 730 and DC S35x0/3610/3700 Series SSDs Device Model: INTEL SSDSC2BB800G4 Serial Number: -- LU WWN Device Id: 5 5cd2e4 ... Firmware Version: D2010370 User Capacity: 800,166,076,416 bytes [800 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Jul 13 21:25:32 2023 CST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x79) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 49321 12 Power_Cycle_Count -O--CK 100 100 000 - 3427 170 Available_Reservd_Space PO--CK 100 100 010 - 0 171 Program_Fail_Count -O--CK 100 100 000 - 0 172 Erase_Fail_Count -O--CK 100 100 000 - 0 174 Unsafe_Shutdown_Count -O--CK 100 100 000 - 461 175 Power_Loss_Cap_Test PO--CK 100 100 010 - 666 (218 161) 183 SATA_Downshift_Count -O--CK 100 100 000 - 36 184 End-to-End_Error PO--CK 100 100 090 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 190 Temperature_Case -O---K 073 073 000 - 27 (Min/Max 18/27) 192 Unsafe_Shutdown_Count -O--CK 100 100 000 - 461 194 Temperature_Internal -O---K 100 100 000 - 38 197 Current_Pending_Sector -O--CK 100 100 000 - 0 199 CRC_Error_Count -OSRCK 100 100 000 - 31 225 Host_Writes_32MiB -O--CK 100 100 000 - 258100 226 Workld_Media_Wear_Indic -O--CK 100 100 000 - 1249 227 Workld_Host_Reads_Perc -O--CK 100 100 000 - 49 228 Workload_Minutes -O--CK 100 100 000 - 2947811 232 Available_Reservd_Space PO--CK 100 100 010 - 0 233 Media_Wearout_Indicator -O--CK 099 099 000 - 0 234 Thermal_Throttle -O--CK 100 100 000 - 0/0 241 Host_Writes_32MiB -O--CK 100 100 000 - 258100 242 Host_Reads_32MiB -O--CK 100 100 000 - 265029 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 8 Comprehensive SMART error log 0x03 GPL,SL R/O 20 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 2 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xb0 GPL,SL VS 1 Device vendor specific log 0xb1 GPL,SL VS 33 Device vendor specific log 0xdd GPL,SL VS 1 Device vendor specific log 0xde GPL VS 768 Device vendor specific log 0xdf GPL VS 1152 Device vendor specific log 0xdf SL VS 128 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (20 sectors) Device Error Count: 5 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Warning! SMART Extended Comprehensive Error Log Structure error: invalid SMART checksum. Error 5 [4] occurred at disk power-on lifetime: 45154 hours (1881 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 10 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 47 00 00 00 01 00 00 00 00 00 10 a0 08 04:22:30.471 READ LOG DMA EXT 61 00 00 04 00 00 00 28 19 17 48 40 00 04:22:30.462 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 03 92 d6 80 40 00 04:22:25.033 WRITE FPDMA QUEUED 61 00 00 00 e8 00 00 03 92 d5 a0 40 00 04:22:25.032 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 03 92 d1 a0 40 00 04:22:25.032 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 45154 hours (1881 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 04 00 00 00 28 19 17 48 40 00 Error: ICRC, ABRT at LBA = 0x28191748 = 672733000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 04 00 00 00 28 19 17 48 40 00 04:22:30.462 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 03 92 d6 80 40 00 04:22:25.033 WRITE FPDMA QUEUED 61 00 00 00 e8 00 00 03 92 d5 a0 40 00 04:22:25.032 WRITE FPDMA QUEUED 61 00 00 04 00 00 00 03 92 d1 a0 40 00 04:22:25.032 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 04:22:20.529 FLUSH CACHE EXT Error 3 [2] occurred at disk power-on lifetime: 45029 hours (1876 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 10 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 47 00 00 00 01 00 00 00 00 00 10 a0 08 04:08:45.113 READ LOG DMA EXT 61 00 00 00 08 00 00 38 68 5f 48 40 00 04:08:45.104 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 38 67 31 70 40 00 04:08:44.870 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 04:08:44.016 FLUSH CACHE EXT 61 00 00 00 08 00 00 24 d4 c7 18 40 00 04:08:44.016 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 45029 hours (1876 days + 5 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 08 00 00 38 68 5f 48 40 00 Error: ICRC, ABRT at LBA = 0x38685f48 = 946364232 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 00 38 68 5f 48 40 00 04:08:45.104 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 38 67 31 70 40 00 04:08:44.870 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 04:08:44.016 FLUSH CACHE EXT 61 00 00 00 08 00 00 24 d4 c7 18 40 00 04:08:44.016 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 a0 08 04:08:44.016 FLUSH CACHE EXT Error 1 [0] occurred at disk power-on lifetime: 44946 hours (1872 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 41 00 20 00 00 53 cb 14 00 40 00 Error: ICRC, ABRT at LBA = 0x53cb1400 = 1405817856 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 20 00 00 53 cb 14 00 40 00 09:08:31.983 READ FPDMA QUEUED 60 00 00 00 08 00 00 53 d0 bc b8 40 00 09:08:31.983 READ FPDMA QUEUED 60 00 00 00 08 00 00 53 d0 bc b0 40 00 09:08:31.983 READ FPDMA QUEUED 60 00 00 00 08 00 00 53 d0 bc a8 40 00 09:08:31.982 READ FPDMA QUEUED 60 00 00 00 08 00 00 53 d0 bc a0 40 00 09:08:31.982 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 49239 - # 2 Short offline Completed without error 00% 49239 - # 3 Short offline Completed without error 00% 48708 - # 4 Short offline Completed without error 00% 48692 - # 5 Short offline Completed without error 00% 48605 - # 6 Short offline Completed without error 00% 48605 - # 7 Short offline Completed without error 00% 48605 - # 8 Short offline Completed without error 00% 48605 - # 9 Short offline Completed without error 00% 48093 - #10 Short offline Completed without error 00% 48092 - #11 Short offline Completed without error 00% 48092 - #12 Short offline Completed without error 00% 48025 - #13 Short offline Completed without error 00% 46390 - #14 Short offline Completed without error 00% 46390 - #15 Short offline Completed without error 00% 45559 - #16 Short offline Completed without error 00% 41738 - #17 Short offline Completed without error 00% 41738 - #18 Short offline Completed without error 00% 41738 - #19 Short offline Completed without error 00% 41738 - #20 Short offline Completed without error 00% 40657 - #21 Short offline Completed without error 00% 40657 - #22 Short offline Completed without error 00% 37735 - #23 Short offline Completed without error 00% 37732 - #24 Short offline Completed without error 00% 36651 - #25 Short offline Completed without error 00% 36651 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 18/27 Celsius Lifetime Min/Max Temperature: 7/36 Celsius Specified Max Operating Temperature: 70 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 61 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/70 Celsius Min/Max Temperature Limit: 0/70 Celsius Temperature History Size (Index): 478 (405) Index Estimated Time Temperature Celsius 406 2023-07-13 13:28 27 ******** ... ..( 81 skipped). .. ******** 10 2023-07-13 14:50 27 ******** 11 2023-07-13 14:51 ? - 12 2023-07-13 14:52 27 ******** ... ..( 16 skipped). .. ******** 29 2023-07-13 15:09 27 ******** 30 2023-07-13 15:10 28 ********* 31 2023-07-13 15:11 28 ********* 32 2023-07-13 15:12 27 ******** ... ..( 2 skipped). .. ******** 35 2023-07-13 15:15 27 ******** 36 2023-07-13 15:16 ? - 37 2023-07-13 15:17 27 ******** 38 2023-07-13 15:18 27 ******** 39 2023-07-13 15:19 27 ******** 40 2023-07-13 15:20 28 ********* ... ..( 5 skipped). .. ********* 46 2023-07-13 15:26 28 ********* 47 2023-07-13 15:27 ? - 48 2023-07-13 15:28 27 ******** ... ..( 33 skipped). .. ******** 82 2023-07-13 16:02 27 ******** 83 2023-07-13 16:03 28 ********* ... ..( 68 skipped). .. ********* 152 2023-07-13 17:12 28 ********* 153 2023-07-13 17:13 27 ******** ... ..( 39 skipped). .. ******** 193 2023-07-13 17:53 27 ******** 194 2023-07-13 17:54 26 ******* ... ..( 14 skipped). .. ******* 209 2023-07-13 18:09 26 ******* 210 2023-07-13 18:10 27 ******** ... ..( 29 skipped). .. ******** 240 2023-07-13 18:40 27 ******** 241 2023-07-13 18:41 ? - 242 2023-07-13 18:42 24 ***** 243 2023-07-13 18:43 25 ****** 244 2023-07-13 18:44 ? - 245 2023-07-13 18:45 21 ** 246 2023-07-13 18:46 21 ** 247 2023-07-13 18:47 22 *** 248 2023-07-13 18:48 22 *** 249 2023-07-13 18:49 23 **** ... ..( 2 skipped). .. **** 252 2023-07-13 18:52 23 **** 253 2023-07-13 18:53 24 ***** 254 2023-07-13 18:54 24 ***** 255 2023-07-13 18:55 25 ****** 256 2023-07-13 18:56 24 ***** 257 2023-07-13 18:57 24 ***** 258 2023-07-13 18:58 25 ****** ... ..( 8 skipped). .. ****** 267 2023-07-13 19:07 25 ****** 268 2023-07-13 19:08 26 ******* ... ..(118 skipped). .. ******* 387 2023-07-13 21:07 26 ******* 388 2023-07-13 21:08 27 ******** 389 2023-07-13 21:09 26 ******* ... ..( 2 skipped). .. ******* 392 2023-07-13 21:12 26 ******* 393 2023-07-13 21:13 27 ******** ... ..( 11 skipped). .. ******** 405 2023-07-13 21:25 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 3427 --- Lifetime Power-On Resets 0x01 0x018 6 16914846655 --- Logical Sectors Written 0x01 0x020 6 199676104 --- Number of Write Commands 0x01 0x028 6 17368957301 --- Logical Sectors Read 0x01 0x030 6 204188810 --- Number of Read Commands 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 27 --- Current Temperature 0x05 0x010 1 25 --- Average Short Term Temperature 0x05 0x018 1 26 --- Average Long Term Temperature 0x05 0x020 1 34 --- Highest Temperature 0x05 0x028 1 7 --- Lowest Temperature 0x05 0x030 1 28 --- Highest Average Short Term Temperature 0x05 0x038 1 7 --- Lowest Average Short Term Temperature 0x05 0x040 1 26 --- Highest Average Long Term Temperature 0x05 0x048 1 7 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 10106 --- Number of Hardware Resets 0x06 0x010 4 5392 --- Number of ASR Events 0x06 0x018 4 31 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 1 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x000a 4 12 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS