/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.14.2-desktop-3omv2590] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: SSD 256GB Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: FW200326 User Capacity: 256,060,514,304 bytes [256 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: Not in smartctl database ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Apr 27 15:20:34 2025 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 4) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 420 12 Power_Cycle_Count -O--CK 100 100 050 - 402 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute -O--CK 100 100 050 - 0 163 Unknown_Attribute -O--CK 100 100 050 - 76 164 Unknown_Attribute -O--CK 100 100 050 - 0 165 Unknown_Attribute -O--CK 100 100 050 - 0 166 Unknown_Attribute -O--CK 100 100 050 - 0 167 Unknown_Attribute -O--CK 100 100 050 - 0 168 Unknown_Attribute -O--CK 100 100 050 - 0 169 Unknown_Attribute -O--CK 100 100 050 - 0 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 67108864 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 463028 177 Wear_Leveling_Count -O--CK 100 100 050 - 1214275 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 50 194 Temperature_Celsius -O--CK 100 100 050 - 42 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 196 Reallocated_Event_Count -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 0 241 Total_LBAs_Written -O--CK 100 100 050 - 72847 242 Total_LBAs_Read -O--CK 100 100 050 - 86860 249 Unknown_Attribute -O--CK 100 100 050 - 86186 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 6 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [1] occurred at disk power-on lifetime: 272 hours (11 days + 8 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 40 00 38 00 12 be 00 ae f8 00 00 at LBA = 0x12be00aef8 = 80497127160 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 80 00 38 00 12 be 00 ae f8 40 00 00:00:17.580 WRITE FPDMA QUEUED 60 00 10 00 30 00 12 88 00 4f 00 40 00 00:00:17.560 READ FPDMA QUEUED 60 00 40 00 28 00 15 06 00 72 98 40 00 00:00:17.560 READ FPDMA QUEUED 60 00 08 00 20 00 1c 08 00 1f 58 40 00 00:00:17.560 READ FPDMA QUEUED 60 00 10 00 18 00 1c 6e 00 20 48 40 00 00:00:17.560 READ FPDMA QUEUED Error 5 [0] occurred at disk power-on lifetime: 189 hours (7 days + 21 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 40 00 78 00 14 71 00 22 6a 00 00 at LBA = 0x147100226a = 87795180138 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 40 00 78 00 14 71 00 22 6a 40 00 00:00:23.140 READ FPDMA QUEUED 60 00 08 00 70 00 12 b5 00 b2 88 40 00 00:00:23.140 READ FPDMA QUEUED 60 00 20 00 68 00 12 1a 00 a3 9e 40 00 00:00:23.140 READ FPDMA QUEUED 60 00 20 00 60 00 12 1d 00 a3 a6 40 00 00:00:23.140 READ FPDMA QUEUED 60 00 20 00 58 00 12 17 00 a3 76 40 00 00:00:23.140 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 175 hours (7 days + 7 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 40 00 20 00 14 a8 00 c2 a7 00 00 at LBA = 0x14a800c2a7 = 88717968039 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 20 00 20 00 14 a8 00 c2 a7 40 00 00:00:26.450 READ FPDMA QUEUED 60 00 20 00 18 00 12 94 00 70 d3 40 00 00:00:26.450 READ FPDMA QUEUED 60 00 20 00 10 00 14 a8 00 c2 87 40 00 00:00:26.450 READ FPDMA QUEUED 60 00 08 00 08 00 12 7f 00 b3 40 40 00 00:00:26.450 READ FPDMA QUEUED 60 00 20 00 f8 00 12 95 00 70 2b 40 00 00:00:26.450 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 162 hours (6 days + 18 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- e0 00 7f 00 14 17 00 77 28 51 00 Device Fault 127 sectors at LBA = 0x1417007728 = 86285252392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 7f 00 14 17 00 77 28 e0 00 00:00:10.650 READ DMA EXT 25 00 00 00 40 00 14 ce 00 ee 40 e0 00 00:00:10.650 READ DMA EXT 25 00 00 00 40 00 12 3f 00 50 80 e0 00 00:00:10.650 READ DMA EXT 25 00 00 00 40 00 12 3f 00 50 40 e0 00 00:00:10.650 READ DMA EXT 25 00 00 00 40 00 12 3f 00 50 00 e0 00 00:00:10.650 READ DMA EXT SMART Extended Self-test Log Version: 0 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 402 --- Lifetime Power-On Resets 0x01 0x010 4 420 --- Power-on Hours 0x01 0x018 6 4774100992 --- Logical Sectors Written 0x01 0x020 6 63789231 --- Number of Write Commands 0x01 0x028 6 5692456960 --- Logical Sectors Read 0x01 0x030 6 74567557 --- Number of Read Commands |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0009 4 419 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2440 Device-to-host register FISes sent due to a COMRESET 0x000b 4 7 CRC errors within host-to-device FIS 0x000d 4 7 Non-CRC errors within host-to-device FIS