/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.12.1-desktop-1omv2490] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: SK hynix SC210 2.5 7MM 128GB Serial Number: -- Firmware Version: 20001L00 User Capacity: 128,035,676,160 bytes [128 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Sun Aug 3 09:12:50 2025 AEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 10) seconds. Offline data collection capabilities: (0x19) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 8) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Retired_Block_Count -O--CK 253 253 036 - 0 9 Power_On_Hours -O--CK 094 094 000 - 5835 12 Power_Cycle_Count -O--CK 100 100 020 - 331 100 Total_Erase_Count -O--CK 100 100 000 - 717369 171 Program_Fail_Count -O--CK 253 253 000 - 0 172 Erase_Fail_Count -O--CK 253 253 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 100 100 000 - 30 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Unused_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 100 100 000 - 12 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 000 - 16 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 52 180 Erase_Fail_Count -O--CK 100 100 000 - 1948 181 Non4k_Aligned_Access -O--CK 253 253 000 - 0 182 Erase_Fail_Count_Total -O--CK 253 253 000 - 0 183 SATA_Downshift_Count -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 191 Unknown_SK_hynix_Attrib -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 021 000 000 - 21 (Min/Max 8/33) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 201 Percent_Lifetime_Remain -OSR-- 100 100 000 - 0 204 Soft_ECC_Correction -OSR-- 100 100 --- - 0 231 SSD_Life_Left PO--CK 253 253 --- - 0 234 Unknown_SK_hynix_Attrib -O--CK 100 100 --- - 1481 241 Total_Writes_GB -O--CK 100 100 --- - 1144 242 Total_Reads_GB -O--CK 100 100 --- - 1580 250 Read_Retry_Count -O--CK 253 253 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 1186 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1186 [5] occurred at disk power-on lifetime: 5835 hours (243 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 00 00 00 00 c2 4f 00 e0 08 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 db 00 f8 00 00 00 c2 4f 00 00 00 00:00:17.720 SMART EN/DISABLE AUTO OFFLINE [NS (SFF-8035i)] 60 01 00 00 78 00 00 06 8d 95 d8 40 40 00:00:17.720 READ FPDMA QUEUED b0 00 d1 00 01 00 00 00 c2 4f 01 00 00 00:00:17.720 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] 60 00 20 00 58 00 00 01 29 7d b8 40 40 00:00:17.720 READ FPDMA QUEUED 60 00 08 00 50 00 00 06 ca 84 b0 40 40 00:00:17.720 READ FPDMA QUEUED Error 1185 [4] occurred at disk power-on lifetime: 5835 hours (243 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 50 00 01 00 00 00 00 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 a0 a0 00:00:14.280 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 a0 a0 00:00:14.280 NOP [Abort queued commands] 25 00 00 00 40 00 00 05 43 b8 00 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 c0 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 80 e0 e0 00:00:11.880 READ DMA EXT Error 1184 [3] occurred at disk power-on lifetime: 5835 hours (243 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 05 43 b8 00 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 c0 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 80 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 40 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 00 e0 e0 00:00:11.880 READ DMA EXT Error 1183 [2] occurred at disk power-on lifetime: 5835 hours (243 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 05 43 b8 00 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 c0 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 80 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 40 e0 e0 00:00:11.880 READ DMA EXT 25 00 00 00 40 00 00 05 43 b7 00 e0 e0 00:00:11.880 READ DMA EXT Error 1182 [1] occurred at disk power-on lifetime: 5835 hours (243 days + 3 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- Error 1181 [0] occurred at disk power-on lifetime: 5834 hours (243 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 51 00 02 00 00 00 c2 4f 00 e0 08 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- b0 00 db 00 f8 00 00 00 c2 4f 00 00 00 00:00:28.070 SMART EN/DISABLE AUTO OFFLINE [NS (SFF-8035i)] b0 00 d1 00 01 00 00 00 c2 4f 01 00 00 00:00:28.070 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] b0 00 d0 00 01 00 00 00 c2 4f 00 00 00 00:00:28.060 SMART READ DATA b0 00 da 00 00 00 00 00 c2 4f 00 00 00 00:00:28.060 SMART RETURN STATUS b0 00 d2 00 f1 00 00 00 c2 4f 00 00 00 00:00:28.060 SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE Error 1180 [19] occurred at disk power-on lifetime: 5834 hours (243 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 50 00 01 00 00 00 00 00 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 00 00 00 00 00 00 00 00 00 00 a0 a0 00:00:22.980 NOP [Abort queued commands] 00 00 00 00 00 00 00 00 00 00 00 a0 a0 00:00:22.980 NOP [Abort queued commands] ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT Error 1179 [18] occurred at disk power-on lifetime: 5834 hours (243 days + 2 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 00 00 00 00 00 00 00 00 ff Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT ea 00 00 00 01 00 00 00 00 00 00 e0 e0 00:00:12.620 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5824 - # 2 Short offline Completed without error 00% 0 - Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (empty) == 0x05 ===== = = === == Temperature Statistics (empty) == 0x06 ===== = = === == Transport Statistics (empty) == 0x07 ===== = = === == Solid State Device Statistics (empty) == |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET