/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-37-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725032GLA380 Serial Number: -- Firmware Version: GM3OA57A User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Dec 24 16:28:41 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5908) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 98) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 096 016 - 0 2 Throughput_Performance P-S--- 128 100 054 - 163 3 Spin_Up_Time POS--- 123 100 024 - 308 (Average 315) 4 Start_Stop_Count -O--C- 100 100 000 - 3300 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 020 - 144 9 Power_On_Hours -O--C- 096 096 000 - 30612 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3289 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4384 193 Load_Cycle_Count -O--C- 097 097 000 - 4384 194 Temperature_Celsius -O---- 146 113 000 - 41 (Min/Max 17/54) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 30510 - # 2 Short offline Completed without error 00% 30508 - # 3 Short offline Completed without error 00% 30508 - # 4 Short offline Completed without error 00% 30318 - # 5 Short offline Completed without error 00% 30161 - # 6 Short offline Completed without error 00% 29991 - # 7 Short offline Completed without error 00% 29991 - # 8 Extended offline Aborted by host 90% 29987 - # 9 Extended offline Completed without error 00% 29986 - #10 Short offline Completed without error 00% 29985 - #11 Short offline Completed without error 00% 1857 - #12 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 28/41 Celsius Lifetime Min/Max Temperature: 17/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (52) Index Estimated Time Temperature Celsius 53 2023-12-24 14:21 39 ******************** 54 2023-12-24 14:22 40 ********************* 55 2023-12-24 14:23 39 ******************** 56 2023-12-24 14:24 40 ********************* ... ..( 2 skipped). .. ********************* 59 2023-12-24 14:27 40 ********************* 60 2023-12-24 14:28 39 ******************** 61 2023-12-24 14:29 40 ********************* ... ..(117 skipped). .. ********************* 51 2023-12-24 16:27 40 ********************* 52 2023-12-24 16:28 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-37-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725032GLA380 Serial Number: -- Firmware Version: GM3OA57A User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Dec 24 16:28:42 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Unavailable Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5908) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 98) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 086 016 - 0 2 Throughput_Performance P-S--- 129 100 054 - 156 3 Spin_Up_Time POS--- 121 100 024 - 315 (Average 318) 4 Start_Stop_Count -O--C- 099 099 000 - 7435 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 129 100 020 - 30 9 Power_On_Hours -O--C- 095 095 000 - 39612 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 6990 192 Power-Off_Retract_Count -O--CK 094 094 000 - 7871 193 Load_Cycle_Count -O--C- 094 094 000 - 7871 194 Temperature_Celsius -O---- 176 111 000 - 34 (Min/Max 17/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 13 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [0] occurred at disk power-on lifetime: 8400 hours (350 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 a8 00 00 02 70 81 d7 42 00 Error: UNC 168 sectors at LBA = 0x027081d7 = 40927703 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 02 70 81 7f 40 00 01:37:52.500 READ DMA EXT 35 00 ff 00 08 00 00 00 60 84 af 40 00 01:37:52.500 WRITE DMA EXT 35 00 ff 00 08 00 00 00 60 7a af 40 00 01:37:52.500 WRITE DMA EXT 35 00 ff 00 08 00 00 00 60 77 d7 40 00 01:37:52.500 WRITE DMA EXT 35 00 ff 00 08 00 00 00 60 75 ff 40 00 01:37:52.500 WRITE DMA EXT Error 12 [3] occurred at disk power-on lifetime: 8400 hours (350 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 70 81 d7 42 00 Error: UNC 8 sectors at LBA = 0x027081d7 = 40927703 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 20 00 00 02 70 81 bf 40 00 01:37:48.100 READ DMA EXT 35 00 ff 00 20 00 00 02 75 92 bf 40 00 01:37:48.100 WRITE DMA EXT 25 00 ff 00 20 00 00 02 70 81 9f 40 00 01:37:48.100 READ DMA EXT 35 00 ff 00 20 00 00 02 75 92 9f 40 00 01:37:48.100 WRITE DMA EXT 25 00 ff 00 20 00 00 02 70 81 7f 40 00 01:37:48.100 READ DMA EXT Error 11 [2] occurred at disk power-on lifetime: 8400 hours (350 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 a8 00 00 02 70 81 d7 42 00 Error: UNC 168 sectors at LBA = 0x027081d7 = 40927703 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 01 00 00 00 02 70 81 7f 40 00 01:36:49.500 READ DMA EXT ea ff 00 00 00 00 00 00 00 00 00 00 00 01:36:49.400 FLUSH CACHE EXT 35 00 ff 00 08 00 00 00 5e 00 3f 40 00 01:36:49.400 WRITE DMA EXT 35 00 ff 00 08 00 00 00 14 03 8a 40 00 01:36:49.400 WRITE DMA EXT 35 00 ff 00 08 00 00 00 61 6c 6f 40 00 01:36:49.400 WRITE DMA EXT Error 10 [1] occurred at disk power-on lifetime: 8400 hours (350 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 02 70 81 d7 42 00 Error: UNC 8 sectors at LBA = 0x027081d7 = 40927703 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 ff 00 20 00 00 02 70 81 bf 40 00 01:36:44.900 READ DMA EXT 35 00 ff 00 20 00 00 02 75 92 3f 40 00 01:36:44.900 WRITE DMA EXT 25 00 ff 00 20 00 00 02 70 81 9f 40 00 01:36:44.900 READ DMA EXT 35 00 ff 00 20 00 00 02 75 92 1f 40 00 01:36:44.900 WRITE DMA EXT 25 00 ff 00 20 00 00 02 70 81 7f 40 00 01:36:44.900 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 39510 - # 2 Short offline Completed without error 00% 39509 - # 3 Short offline Completed without error 00% 39508 - # 4 Short offline Completed without error 00% 39318 - # 5 Short offline Completed without error 00% 36315 - # 6 Extended offline Completed without error 00% 36159 - # 7 Short offline Completed without error 00% 36157 - # 8 Short offline Completed without error 00% 36114 - # 9 Short offline Completed without error 00% 36043 - #10 Short offline Completed without error 00% 35990 - #11 Extended offline Completed without error 00% 33986 - #12 Extended offline Completed without error 00% 31152 - #13 Short offline Completed without error 00% 30985 - #14 Short offline Completed without error 00% 30985 - #15 Short offline Completed without error 00% 16643 - #16 Short offline Completed without error 00% 2509 - #17 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 34 Celsius Power Cycle Min/Max Temperature: 20/35 Celsius Lifetime Min/Max Temperature: 17/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (114) Index Estimated Time Temperature Celsius 115 2023-12-24 14:21 35 **************** ... ..( 9 skipped). .. **************** 125 2023-12-24 14:31 35 **************** 126 2023-12-24 14:32 34 *************** ... ..( 7 skipped). .. *************** 6 2023-12-24 14:40 34 *************** 7 2023-12-24 14:41 35 **************** ... ..( 12 skipped). .. **************** 20 2023-12-24 14:54 35 **************** 21 2023-12-24 14:55 34 *************** ... ..( 3 skipped). .. *************** 25 2023-12-24 14:59 34 *************** 26 2023-12-24 15:00 35 **************** ... ..( 14 skipped). .. **************** 41 2023-12-24 15:15 35 **************** 42 2023-12-24 15:16 34 *************** ... ..( 3 skipped). .. *************** 46 2023-12-24 15:20 34 *************** 47 2023-12-24 15:21 35 **************** 48 2023-12-24 15:22 34 *************** ... ..( 65 skipped). .. *************** 114 2023-12-24 16:28 34 *************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdf smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-37-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: ST12000NM0127 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: G005 User Capacity: 12,000,138,625,024 bytes [12.0 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: Not in smartctl database 7.3/5319 ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Dec 24 16:28:43 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status command failed: Connection timed out SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 567) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: (1090) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x50bd) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 044 - 15256 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 1 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 253 045 - 58478 9 Power_On_Hours -O--CK 100 100 000 - 4 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 2 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 253 000 - 0 190 Airflow_Temperature_Cel -O---K 064 064 040 - 36 (Min/Max 18/36) 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1 193 Load_Cycle_Count -O--CK 100 100 000 - 2 194 Temperature_Celsius -O---K 036 040 000 - 36 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 15256 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate PO---K 100 100 001 - 0 240 Head_Flying_Hours ------ 100 253 000 - 4 (0 36 0) 241 Total_LBAs_Written ------ 100 253 000 - 0 242 Total_LBAs_Read ------ 100 253 000 - 15256 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL R/O 256 Device Statistics log 0x04 SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x0c GPL R/O 2048 Pending Defects log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x13 GPL R/O 1 SATA NCQ Send and Receive log 0x15 GPL R/W 1 Rebuild Assist log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 768 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 24 Device vendor specific log 0xa2 GPL VS 16320 Device vendor specific log 0xa4 GPL,SL VS 160 Device vendor specific log 0xa6 GPL VS 192 Device vendor specific log 0xa8-0xa9 GPL,SL VS 136 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xad GPL VS 16 Device vendor specific log 0xaf GPL,SL VS 1 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc1 GPL,SL VS 8 Device vendor specific log 0xc3 GPL,SL VS 32 Device vendor specific log 0xc9 GPL,SL VS 8 Device vendor specific log 0xca GPL,SL VS 16 Device vendor specific log 0xd1 GPL VS 336 Device vendor specific log 0xd2 GPL VS 10000 Device vendor specific log 0xd4 GPL VS 2048 Device vendor specific log 0xda GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 18/36 Celsius Lifetime Min/Max Temperature: 17/36 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 68 01 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 3 minutes Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 10/40 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (8) Index Estimated Time Temperature Celsius 9 2023-12-19 11:06 ? - ... ..(117 skipped). .. - 127 2023-12-24 07:08 ? - 0 2023-12-24 08:07 18 - 1 2023-12-24 09:06 ? - 2 2023-12-24 10:05 17 - 3 2023-12-24 11:04 ? - 4 2023-12-24 12:03 18 - 5 2023-12-24 13:02 33 ************** 6 2023-12-24 14:01 35 **************** 7 2023-12-24 15:00 35 **************** 8 2023-12-24 15:59 35 **************** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 2 --- Lifetime Power-On Resets 0x01 0x010 4 4 --- Power-on Hours 0x01 0x018 6 0 --- Logical Sectors Written 0x01 0x020 6 0 --- Number of Write Commands 0x01 0x028 6 15256 --- Logical Sectors Read 0x01 0x030 6 452 --- Number of Read Commands 0x01 0x038 6 - --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 4 --- Spindle Motor Power-on Hours 0x03 0x010 4 4 --- Head Flying Hours 0x03 0x018 4 2 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x03 0x040 4 0 --- Number of High Priority Unload Events 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 36 --- Current Temperature 0x05 0x010 1 - --- Average Short Term Temperature 0x05 0x018 1 - --- Average Long Term Temperature 0x05 0x020 1 36 --- Highest Temperature 0x05 0x028 1 27 --- Lowest Temperature 0x05 0x030 1 - --- Highest Average Short Term Temperature 0x05 0x038 1 - --- Lowest Average Short Term Temperature 0x05 0x040 1 - --- Highest Average Long Term Temperature 0x05 0x048 1 - --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 0 --- Number of Hardware Resets 0x06 0x010 4 0 --- Number of ASR Events 0x06 0x018 4 0 --- Number of Interface CRC Errors 0xff ===== = = === == Vendor Specific Statistics (rev 1) == 0xff 0x008 7 0 --- Vendor Specific 0xff 0x018 7 0 --- Vendor Specific |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) No Defects Logged SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdj smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.2.0-37-generic] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 2.5" HDD MQ01ABD... Device Model: TOSHIBA MQ01ABD100 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: AX001U User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Dec 24 16:29:45 2023 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART Status not supported: Incomplete response, ATA output registers missing SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 236) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 050 - 0 2 Throughput_Performance P-S--- 100 100 050 - 0 3 Spin_Up_Time POS--K 100 100 001 - 660 4 Start_Stop_Count -O--CK 100 100 000 - 1459 5 Reallocated_Sector_Ct PO--CK 100 100 050 - 0 7 Seek_Error_Rate PO-R-- 100 100 050 - 0 8 Seek_Time_Performance P-S--- 100 100 050 - 0 9 Power_On_Hours -O--CK 059 059 000 - 16457 10 Spin_Retry_Count PO--CK 128 100 030 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 121 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 10 193 Load_Cycle_Count -O--CK 051 051 000 - 491132 194 Temperature_Celsius -O---K 100 100 000 - 22 (Min/Max 15/55) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--CK 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 134 220 Disk_Shift -O---- 100 100 000 - 0 222 Loaded_Hours -O--CK 093 093 000 - 3024 223 Load_Retry_Count -O--CK 100 100 000 - 0 224 Load_Friction -O---K 100 100 000 - 0 226 Load-in_Time -OS--K 100 100 000 - 266 240 Head_Flying_Hours P----- 100 100 001 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 134 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 134 [133] occurred at disk power-on lifetime: 13257 hours (552 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 07 e0 00 Error: ICRC, ABRT at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 08 00 00 00 00 00 00 e0 00 2d+08:01:40.758 READ DMA EXT e5 00 03 00 44 00 00 00 00 00 01 e0 00 2d+08:01:40.730 CHECK POWER MODE ec 00 03 00 44 00 00 00 00 00 01 e0 00 2d+08:01:40.727 IDENTIFY DEVICE ef 00 03 00 44 00 00 00 00 00 01 e0 00 2d+08:01:38.455 SET FEATURES [Set transfer mode] ec 00 00 00 01 00 00 00 00 00 01 e0 00 2d+08:01:38.453 IDENTIFY DEVICE Error 133 [132] occurred at disk power-on lifetime: 9795 hours (408 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 11 00 00 3a 39 c2 af 40 00 Error: ICRC, ABRT 17 sectors at LBA = 0x3a39c2af = 976863919 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 3a 39 c2 40 40 00 18d+10:34:18.300 WRITE DMA EXT 35 00 00 00 80 00 00 3a 39 c1 c0 40 00 18d+10:34:18.299 WRITE DMA EXT 35 00 00 00 80 00 00 3a 39 c1 40 40 00 18d+10:34:18.298 WRITE DMA EXT e7 00 00 00 00 00 00 00 00 00 00 00 00 18d+10:34:18.206 FLUSH CACHE 35 00 00 00 01 00 00 3a 39 04 80 40 00 18d+10:34:18.205 WRITE DMA EXT Error 132 [131] occurred at disk power-on lifetime: 9715 hours (404 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 31 00 00 3a 39 ae d1 40 00 Error: ICRC, ABRT 49 sectors at LBA = 0x3a39aed1 = 976858833 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 3a 39 ae 82 40 00 15d+02:46:26.500 WRITE DMA EXT e7 00 00 00 00 00 00 00 00 00 00 00 00 15d+02:46:26.182 FLUSH CACHE 35 00 00 00 01 00 00 3a 39 04 80 40 00 15d+02:46:26.181 WRITE DMA EXT 35 00 00 00 10 00 00 00 07 1d 18 40 00 15d+02:46:26.179 WRITE DMA EXT b0 00 da 00 00 00 00 00 c2 4f 00 00 00 15d+02:45:26.470 SMART RETURN STATUS Error 131 [130] occurred at disk power-on lifetime: 9713 hours (404 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 09 00 00 3b 5c 8b 6f 40 00 Error: ICRC, ABRT 9 sectors at LBA = 0x3b5c8b6f = 995920751 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 78 00 00 3b 5c 8b 00 40 00 15d+01:09:22.780 WRITE DMA EXT 35 00 00 00 08 00 00 3b 5c 8a f8 40 00 15d+01:09:22.780 WRITE DMA EXT 35 00 00 00 08 00 00 3b 5a 2a 20 40 00 15d+01:09:22.780 WRITE DMA EXT 35 00 00 00 10 00 00 3b 5a 2a 10 40 00 15d+01:09:22.779 WRITE DMA EXT 35 00 00 00 08 00 00 3b 5a 2a 08 40 00 15d+01:09:22.779 WRITE DMA EXT Error 130 [129] occurred at disk power-on lifetime: 9713 hours (404 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 3a 81 cb af 40 00 Error: ICRC, ABRT 1 sectors at LBA = 0x3a81cbaf = 981584815 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 10 00 00 3a 81 cb a0 40 00 15d+01:09:21.938 WRITE DMA EXT 35 00 00 00 10 00 00 3a 7d 3d 10 40 00 15d+01:09:21.938 WRITE DMA EXT 35 00 00 00 10 00 00 3a 7d 3c 90 40 00 15d+01:09:21.938 WRITE DMA EXT 35 00 00 00 10 00 00 3a 7d 3c 80 40 00 15d+01:09:21.938 WRITE DMA EXT 35 00 00 00 08 00 00 3a 38 92 48 40 00 15d+01:09:21.937 WRITE DMA EXT Error 129 [128] occurred at disk power-on lifetime: 9713 hours (404 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 31 00 00 3a 39 91 d3 40 00 Error: ICRC, ABRT 49 sectors at LBA = 0x3a3991d3 = 976851411 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 3a 39 91 84 40 00 15d+01:09:20.576 WRITE DMA EXT e7 00 00 00 00 00 00 00 00 00 00 00 00 15d+01:09:20.496 FLUSH CACHE 35 00 00 00 01 00 00 3a 39 04 80 40 00 15d+01:09:20.495 WRITE DMA EXT 35 00 00 00 08 00 00 3b 59 fb 60 40 00 15d+01:09:20.493 WRITE DMA EXT 35 00 00 00 10 00 00 3a 81 cb a0 40 00 15d+01:09:20.493 WRITE DMA EXT Error 128 [127] occurred at disk power-on lifetime: 9713 hours (404 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 71 00 00 3a 39 8b 25 40 00 Error: ICRC, ABRT 113 sectors at LBA = 0x3a398b25 = 976849701 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 3a 39 8b 16 40 00 15d+01:09:19.523 WRITE DMA EXT 35 00 00 00 08 00 00 3b 5a 1a 90 40 00 15d+01:09:19.521 WRITE DMA EXT 35 00 00 00 10 00 00 3a 81 cb a0 40 00 15d+01:09:19.521 WRITE DMA EXT 35 00 00 00 10 00 00 3a 7d 3c c0 40 00 15d+01:09:19.521 WRITE DMA EXT 35 00 00 00 08 00 00 3a 38 92 48 40 00 15d+01:09:19.521 WRITE DMA EXT Error 127 [126] occurred at disk power-on lifetime: 9713 hours (404 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 3a 39 89 0c 40 00 Error: ICRC, ABRT 1 sectors at LBA = 0x3a39890c = 976849164 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 80 00 00 3a 39 88 8d 40 00 15d+01:09:19.026 WRITE DMA EXT 25 00 00 00 10 00 00 3a 81 cb b0 40 00 15d+01:09:19.026 READ DMA EXT 35 00 00 00 08 00 00 3a c8 93 58 40 00 15d+01:09:19.024 WRITE DMA EXT 25 00 00 00 10 00 00 3a 81 cd d0 40 00 15d+01:09:19.003 READ DMA EXT 35 00 00 00 10 00 00 3a 7d 3c d0 40 00 15d+01:09:19.003 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 21 Celsius Power Cycle Min/Max Temperature: 15/38 Celsius Lifetime Min/Max Temperature: 15/55 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/55 Celsius Min/Max Temperature Limit: 5/55 Celsius Temperature History Size (Index): 478 (363) Index Estimated Time Temperature Celsius 364 2023-12-24 08:32 19 - ... ..(199 skipped). .. - 86 2023-12-24 11:52 19 - 87 2023-12-24 11:53 26 ******* 88 2023-12-24 11:54 25 ****** 89 2023-12-24 11:55 25 ****** 90 2023-12-24 11:56 24 ***** 91 2023-12-24 11:57 24 ***** 92 2023-12-24 11:58 23 **** ... ..( 2 skipped). .. **** 95 2023-12-24 12:01 23 **** 96 2023-12-24 12:02 22 *** ... ..( 5 skipped). .. *** 102 2023-12-24 12:08 22 *** 103 2023-12-24 12:09 21 ** ... ..(101 skipped). .. ** 205 2023-12-24 13:51 21 ** 206 2023-12-24 13:52 20 * 207 2023-12-24 13:53 21 ** ... ..( 5 skipped). .. ** 213 2023-12-24 13:59 21 ** 214 2023-12-24 14:00 20 * 215 2023-12-24 14:01 21 ** ... ..(147 skipped). .. ** 363 2023-12-24 16:29 21 ** SMART WRITE LOG does not return COUNT and LBA_LOW register SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 121 --- Lifetime Power-On Resets 0x01 0x010 4 16457 --- Power-on Hours 0x01 0x018 6 3187988436 --- Logical Sectors Written 0x01 0x020 6 40066411 --- Number of Write Commands 0x01 0x028 6 2215524160 --- Logical Sectors Read 0x01 0x030 6 41068616 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (rev 1) == 0x02 0x010 4 0 --- Overlimit Shock Events 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 10420 --- Spindle Motor Power-on Hours 0x03 0x010 4 3024 --- Head Flying Hours 0x03 0x018 4 491132 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 4 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 22 --- Current Temperature 0x05 0x010 1 19 N-- Average Short Term Temperature 0x05 0x018 1 24 N-- Average Long Term Temperature 0x05 0x020 1 55 --- Highest Temperature 0x05 0x028 1 15 --- Lowest Temperature 0x05 0x030 1 46 N-- Highest Average Short Term Temperature 0x05 0x038 1 16 N-- Lowest Average Short Term Temperature 0x05 0x040 1 43 N-- Highest Average Long Term Temperature 0x05 0x048 1 23 N-- Lowest Average Long Term Temperature 0x05 0x050 4 21 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 5 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 14002592 --- Number of Hardware Resets 0x06 0x018 4 134 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 27 N-- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 64 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 59 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC