/dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.10.118-generic-2rosa2021.1-x86_64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Samsung SpinPoint M8 (AF) Device Model: ST1000LM024 HN-M101MBB Serial Number: -- LU WWN Device Id: 5 0004cf ... Firmware Version: 2AR20002 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 3.0, 3.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jun 26 02:01:30 2022 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13140) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 219) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 26 2 Throughput_Performance -OS--K 056 056 000 - 11987 3 Spin_Up_Time PO---K 090 088 025 - 3057 4 Start_Stop_Count -O--CK 098 098 000 - 2022 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 13346 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 629 12 Power_Cycle_Count -O--CK 098 098 000 - 2021 191 G-Sense_Error_Rate -O---K 100 100 000 - 10081 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 051 045 000 - 49 (Min/Max -7/55) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 4282 223 Load_Retry_Count -O--CK 100 100 000 - 629 225 Load_Cycle_Count -O--CK 078 078 000 - 229809 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xc0-0xdf GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 19 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 19 [2] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.063 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.063 SET FEATURES [Enable write cache] 00 00 00 00 20 00 00 14 69 b7 60 40 00 00:00:00.063 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 18 [1] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.061 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.061 SET FEATURES [Enable write cache] 00 00 00 00 20 00 00 14 3b 02 40 40 00 00:00:00.061 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 17 [0] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.058 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.058 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 69 b7 60 40 00 00:00:00.058 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 16 [7] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.056 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.056 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 69 b3 60 40 00 00:00:00.056 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 15 [6] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.053 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.053 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 59 fb a0 40 00 00:00:00.053 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 14 [5] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.051 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.051 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 59 f7 a0 40 00 00:00:00.051 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED Error 13 [4] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.020 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.049 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.049 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 4a d7 e0 40 00 00:00:00.049 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.019 READ FPDMA QUEUED Error 12 [3] occurred at disk power-on lifetime: 13012 hours (542 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 41 00 08 00 00 00 5e de c8 40 00 Error: UNC at LBA = 0x005edec8 = 6217416 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.019 READ FPDMA QUEUED 60 00 02 00 08 00 00 00 5e de c8 40 00 00:00:00.046 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 00:00:00.046 SET FEATURES [Enable write cache] 00 00 00 01 00 00 00 14 4a d3 e0 40 00 00:00:00.046 NOP [Abort queued commands] 60 00 00 00 08 00 00 00 5e de c8 40 00 00:00:00.019 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 13326 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 49 Celsius Power Cycle Min/Max Temperature: 48/49 Celsius Lifetime Min/Max Temperature: -7/54 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 1/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2022-06-25 15:25 49 ****************************** 115 2022-06-25 15:30 48 ***************************** 116 2022-06-25 15:35 49 ****************************** ... ..( 5 skipped). .. ****************************** 122 2022-06-25 16:05 49 ****************************** 123 2022-06-25 16:10 50 ******************************* 124 2022-06-25 16:15 49 ****************************** 125 2022-06-25 16:20 50 ******************************* ... ..( 58 skipped). .. ******************************* 56 2022-06-25 21:15 50 ******************************* 57 2022-06-25 21:20 49 ****************************** ... ..( 5 skipped). .. ****************************** 63 2022-06-25 21:50 49 ****************************** 64 2022-06-25 21:55 50 ******************************* ... ..( 28 skipped). .. ******************************* 93 2022-06-26 00:20 50 ******************************* 94 2022-06-26 00:25 49 ****************************** ... ..( 18 skipped). .. ****************************** 113 2022-06-26 02:00 49 ****************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0003 4 0 R_ERR response for device-to-host data FIS 0x0004 4 0 R_ERR response for host-to-device data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x0006 4 0 R_ERR response for device-to-host non-data FIS 0x0007 4 0 R_ERR response for host-to-device non-data FIS 0x0008 4 0 Device-to-host non-data FIS retries 0x0009 4 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 3 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC 0x8e00 4 0 Vendor specific 0x8e01 4 0 Vendor specific 0x8e02 4 0 Vendor specific 0x8e03 4 0 Vendor specific 0x8e04 4 0 Vendor specific 0x8e05 4 0 Vendor specific 0x8e06 4 0 Vendor specific 0x8e07 4 0 Vendor specific 0x8e08 4 0 Vendor specific 0x8e09 4 0 Vendor specific 0x8e0a 4 0 Vendor specific 0x8e0b 4 0 Vendor specific 0x8e0c 4 0 Vendor specific 0x8e0d 4 0 Vendor specific 0x8e0e 4 0 Vendor specific 0x8e0f 4 0 Vendor specific 0x8e10 4 0 Vendor specific 0x8e11 4 0 Vendor specific