/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD5000AAKX-001CA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 15.01H15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Sep 20 11:54:20 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 88) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 143 139 021 - 3850 4 Start_Stop_Count -O--CK 099 099 000 - 1347 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 096 096 000 - 3130 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1299 192 Power-Off_Retract_Count -O--CK 199 199 000 - 787 193 Load_Cycle_Count -O--CK 200 200 000 - 559 194 Temperature_Celsius -O---K 102 089 000 - 41 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 41/41 Celsius Lifetime Min/Max Temperature: 40/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (22) Index Estimated Time Temperature Celsius 23 2020-09-20 03:57 41 ********************** ... ..( 3 skipped). .. ********************** 27 2020-09-20 04:01 41 ********************** 28 2020-09-20 04:02 ? - 29 2020-09-20 04:03 41 ********************** ... ..( 13 skipped). .. ********************** 43 2020-09-20 04:17 41 ********************** 44 2020-09-20 04:18 ? - 45 2020-09-20 04:19 41 ********************** ... ..( 16 skipped). .. ********************** 62 2020-09-20 04:36 41 ********************** 63 2020-09-20 04:37 ? - 64 2020-09-20 04:38 41 ********************** 65 2020-09-20 04:39 ? - 66 2020-09-20 04:40 41 ********************** 67 2020-09-20 04:41 ? - 68 2020-09-20 04:42 41 ********************** 69 2020-09-20 04:43 41 ********************** 70 2020-09-20 04:44 ? - 71 2020-09-20 04:45 41 ********************** 72 2020-09-20 04:46 ? - 73 2020-09-20 04:47 41 ********************** ... ..( 34 skipped). .. ********************** 108 2020-09-20 05:22 41 ********************** 109 2020-09-20 05:23 40 ********************* ... ..( 6 skipped). .. ********************* 116 2020-09-20 05:30 40 ********************* 117 2020-09-20 05:31 ? - 118 2020-09-20 05:32 41 ********************** ... ..( 3 skipped). .. ********************** 122 2020-09-20 05:36 41 ********************** 123 2020-09-20 05:37 42 *********************** ... ..( 3 skipped). .. *********************** 127 2020-09-20 05:41 42 *********************** 128 2020-09-20 05:42 43 ************************ 129 2020-09-20 05:43 43 ************************ 130 2020-09-20 05:44 42 *********************** ... ..( 8 skipped). .. *********************** 139 2020-09-20 05:53 42 *********************** 140 2020-09-20 05:54 43 ************************ ... ..( 11 skipped). .. ************************ 152 2020-09-20 06:06 43 ************************ 153 2020-09-20 06:07 ? - 154 2020-09-20 06:08 43 ************************ 155 2020-09-20 06:09 43 ************************ 156 2020-09-20 06:10 43 ************************ 157 2020-09-20 06:11 42 *********************** ... ..( 29 skipped). .. *********************** 187 2020-09-20 06:41 42 *********************** 188 2020-09-20 06:42 ? - 189 2020-09-20 06:43 42 *********************** 190 2020-09-20 06:44 42 *********************** 191 2020-09-20 06:45 42 *********************** 192 2020-09-20 06:46 ? - 193 2020-09-20 06:47 43 ************************ 194 2020-09-20 06:48 42 *********************** 195 2020-09-20 06:49 42 *********************** 196 2020-09-20 06:50 42 *********************** 197 2020-09-20 06:51 ? - 198 2020-09-20 06:52 43 ************************ 199 2020-09-20 06:53 42 *********************** ... ..( 17 skipped). .. *********************** 217 2020-09-20 07:11 42 *********************** 218 2020-09-20 07:12 43 ************************ 219 2020-09-20 07:13 42 *********************** 220 2020-09-20 07:14 43 ************************ 221 2020-09-20 07:15 42 *********************** 222 2020-09-20 07:16 42 *********************** 223 2020-09-20 07:17 42 *********************** 224 2020-09-20 07:18 43 ************************ 225 2020-09-20 07:19 42 *********************** 226 2020-09-20 07:20 43 ************************ 227 2020-09-20 07:21 42 *********************** 228 2020-09-20 07:22 43 ************************ ... ..( 4 skipped). .. ************************ 233 2020-09-20 07:27 43 ************************ 234 2020-09-20 07:28 42 *********************** 235 2020-09-20 07:29 42 *********************** 236 2020-09-20 07:30 42 *********************** 237 2020-09-20 07:31 ? - 238 2020-09-20 07:32 43 ************************ 239 2020-09-20 07:33 42 *********************** ... ..( 13 skipped). .. *********************** 253 2020-09-20 07:47 42 *********************** 254 2020-09-20 07:48 ? - 255 2020-09-20 07:49 42 *********************** ... ..( 15 skipped). .. *********************** 271 2020-09-20 08:05 42 *********************** 272 2020-09-20 08:06 ? - 273 2020-09-20 08:07 42 *********************** ... ..( 4 skipped). .. *********************** 278 2020-09-20 08:12 42 *********************** 279 2020-09-20 08:13 43 ************************ ... ..( 28 skipped). .. ************************ 308 2020-09-20 08:42 43 ************************ 309 2020-09-20 08:43 44 ************************* ... ..( 47 skipped). .. ************************* 357 2020-09-20 09:31 44 ************************* 358 2020-09-20 09:32 ? - 359 2020-09-20 09:33 44 ************************* ... ..( 16 skipped). .. ************************* 376 2020-09-20 09:50 44 ************************* 377 2020-09-20 09:51 43 ************************ ... ..( 9 skipped). .. ************************ 387 2020-09-20 10:01 43 ************************ 388 2020-09-20 10:02 42 *********************** ... ..( 2 skipped). .. *********************** 391 2020-09-20 10:05 42 *********************** 392 2020-09-20 10:06 41 ********************** ... ..(107 skipped). .. ********************** 22 2020-09-20 11:54 41 ********************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 374 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.11 Device Model: ST3500320AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: SD15 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Sun Sep 20 11:54:20 2020 UTC ==> WARNING: There are known problems with these drives, THIS DRIVE MAY OR MAY NOT BE AFFECTED, see the following web pages for details: http://knowledge.seagate.com/articles/en_US/FAQ/207931en http://knowledge.seagate.com/articles/en_US/FAQ/207951en https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=632758 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 25) The self-test routine was aborted by the host. Total time to complete Offline data collection: ( 642) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 118) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 100 006 - 81319812 3 Spin_Up_Time PO---- 095 091 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 869 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 066 060 030 - 3854262 9 Power_On_Hours -O--CK 098 098 000 - 2171 10 Spin_Retry_Count PO--C- 100 100 097 - 5 12 Power_Cycle_Count -O--CK 099 099 020 - 1777 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 8590065666 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 062 052 045 - 38 (Min/Max 37/38) 194 Temperature_Celsius -O---K 038 048 000 - 38 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 027 015 000 - 81319812 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 175 000 - 333 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2819 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 37/38 Celsius Lifetime Min/Max Temperature: 9/48 Celsius Under/Over Temperature Limit Count: 0/7 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (96) Index Estimated Time Temperature Celsius 97 2020-09-20 09:47 38 ******************* ... ..( 14 skipped). .. ******************* 112 2020-09-20 10:02 38 ******************* 113 2020-09-20 10:03 ? - 114 2020-09-20 10:04 38 ******************* ... ..( 17 skipped). .. ******************* 4 2020-09-20 10:22 38 ******************* 5 2020-09-20 10:23 ? - 6 2020-09-20 10:24 38 ******************* ... ..( 19 skipped). .. ******************* 26 2020-09-20 10:44 38 ******************* 27 2020-09-20 10:45 ? - 28 2020-09-20 10:46 38 ******************* 29 2020-09-20 10:47 ? - 30 2020-09-20 10:48 38 ******************* 31 2020-09-20 10:49 ? - 32 2020-09-20 10:50 38 ******************* ... ..( 3 skipped). .. ******************* 36 2020-09-20 10:54 38 ******************* 37 2020-09-20 10:55 ? - 38 2020-09-20 10:56 38 ******************* 39 2020-09-20 10:57 38 ******************* 40 2020-09-20 10:58 38 ******************* 41 2020-09-20 10:59 ? - 42 2020-09-20 11:00 38 ******************* ... ..( 27 skipped). .. ******************* 70 2020-09-20 11:28 38 ******************* 71 2020-09-20 11:29 37 ****************** ... ..( 16 skipped). .. ****************** 88 2020-09-20 11:46 37 ****************** 89 2020-09-20 11:47 ? - 90 2020-09-20 11:48 37 ****************** ... ..( 2 skipped). .. ****************** 93 2020-09-20 11:51 37 ****************** 94 2020-09-20 11:52 38 ******************* 95 2020-09-20 11:53 38 ******************* 96 2020-09-20 11:54 38 ******************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD3200AAKS-00VYA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 12.01B02 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Local Time is: Sun Sep 20 11:54:20 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8400) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 100) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 162 3 Spin_Up_Time PO---- 160 150 021 - 4991 4 Start_Stop_Count -O--CK 098 098 000 - 2992 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 096 096 000 - 3345 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2849 192 Power-Off_Retract_Count -O--CK 198 198 000 - 1582 193 Load_Cycle_Count -O--CK 200 200 000 - 2992 194 Temperature_Celsius -O---K 105 097 000 - 42 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 124 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 124 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c2 60 0f 34 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 0f 30 00 27 ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 d2 ef 0e 1d 00 00 00 37 08 00 00 00 00:15:28.613 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 0d b7 00 21 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 123 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 65 60 0e 2b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 0e d2 00 1d ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 25 ef 0d 14 00 00 00 37 08 00 00 00 00:14:20.599 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 0c ff 00 17 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 122 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 b7 60 0d 21 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 0d 25 00 14 ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 6d ef 0c 0a 00 00 00 37 08 00 00 00 00:13:12.575 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 0b a2 00 0e 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 121 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ff 60 0c 17 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 0c 6d 00 0a ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 5e ef 0b 01 00 00 00 37 08 00 00 00 00:12:04.642 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 0a 2b 00 09 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 120 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a2 60 0b 0e 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 0b 5e 00 01 ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 99 ef 09 fb 00 00 00 37 08 00 00 00 00:10:57.707 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 08 ce 00 ff 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 119 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 2b 60 0a 09 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 09 99 00 fb ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 3b ef 08 f2 00 00 00 37 08 00 00 00 00:09:49.774 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 07 1d 00 f6 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 118 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ce 60 08 ff 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 08 3b 00 f2 ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 8b ef 07 e8 00 00 00 37 08 00 00 00 00:08:41.757 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 06 68 00 ec 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] Error 117 [20] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1d 60 07 f6 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 46 03 00 00 07 8b 00 e8 ef 00 00 00 00:00:14.080 NOP [Reserved subcommand] [OBS-ACS-2] 00 d6 ef 06 de 00 00 00 37 08 00 00 00 00:07:33.736 NOP [Reserved subcommand] [OBS-ACS-2] 00 00 08 00 37 05 0b 00 e3 60 00 00 00 00:00:00.070 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: 42/42 Celsius Lifetime Min/Max Temperature: 42/50 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (123) Index Estimated Time Temperature Celsius 124 2020-09-20 09:47 43 ************************ ... ..( 8 skipped). .. ************************ 5 2020-09-20 09:56 43 ************************ 6 2020-09-20 09:57 42 *********************** ... ..( 15 skipped). .. *********************** 22 2020-09-20 10:13 42 *********************** 23 2020-09-20 10:14 ? - 24 2020-09-20 10:15 42 *********************** ... ..( 15 skipped). .. *********************** 40 2020-09-20 10:31 42 *********************** 41 2020-09-20 10:32 ? - 42 2020-09-20 10:33 42 *********************** ... ..( 15 skipped). .. *********************** 58 2020-09-20 10:49 42 *********************** 59 2020-09-20 10:50 ? - 60 2020-09-20 10:51 42 *********************** 61 2020-09-20 10:52 ? - 62 2020-09-20 10:53 42 *********************** 63 2020-09-20 10:54 ? - 64 2020-09-20 10:55 42 *********************** 65 2020-09-20 10:56 42 *********************** 66 2020-09-20 10:57 42 *********************** 67 2020-09-20 10:58 ? - 68 2020-09-20 10:59 42 *********************** 69 2020-09-20 11:00 ? - 70 2020-09-20 11:01 42 *********************** ... ..( 44 skipped). .. *********************** 115 2020-09-20 11:46 42 *********************** 116 2020-09-20 11:47 ? - 117 2020-09-20 11:48 42 *********************** ... ..( 4 skipped). .. *********************** 122 2020-09-20 11:53 42 *********************** 123 2020-09-20 11:54 43 ************************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x8000 4 380 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST2000DM001-1CH164 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC24 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Sun Sep 20 11:54:20 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 617) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 260) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 112 099 006 - 45413488 3 Spin_Up_Time PO---- 095 094 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1047 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 253 030 - 4295323396 9 Power_On_Hours -O--CK 097 097 000 - 2750 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 872 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 099 000 - 0 2 2 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 063 051 045 - 37 (Min/Max 37/37) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 572 193 Load_Cycle_Count -O--CK 099 099 000 - 2993 194 Temperature_Celsius -O---K 037 049 000 - 37 (0 12 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 2452h+08m+35.283s 241 Total_LBAs_Written ------ 100 253 000 - 297001861 242 Total_LBAs_Read ------ 100 253 000 - 340271148 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 37 Celsius Power Cycle Min/Max Temperature: 37/37 Celsius Lifetime Min/Max Temperature: 12/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax 10 (ATA/133 and SATA/150) Device Model: Maxtor 6L120M0 Serial Number: -- Firmware Version: BANC1E00 User Capacity: 122,942,324,736 bytes [122 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 0 Local Time is: Sun Sep 20 11:54:20 2020 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 192 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable Warning! SMART Attribute Thresholds Structure error: invalid SMART checksum. === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1202) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 3 Spin_Up_Time POS--K 207 206 063 - 11310 4 Start_Stop_Count -O--CK 253 253 000 - 1709 5 Reallocated_Sector_Ct PO--CK 253 253 063 - 0 6 Read_Channel_Margin P----- 253 253 100 - 0 7 Seek_Error_Rate -O-R-- 253 252 000 - 0 8 Seek_Time_Performance POS--K 249 243 187 - 40252 9 Power_On_Minutes -O--CK 239 239 000 - 553h+26m 10 Spin_Retry_Count PO-R-K 253 252 157 - 0 11 Calibration_Retry_Count PO-R-K 253 252 223 - 0 12 Power_Cycle_Count -O--CK 244 244 000 - 3946 192 Power-Off_Retract_Count -O--CK 253 253 000 - 0 193 Load_Cycle_Count -O--CK 253 253 000 - 0 194 Temperature_Celsius -O--CK 039 253 000 - 42 195 Hardware_ECC_Recovered -O-R-- 252 250 000 - 33852 196 Reallocated_Event_Count ---R-- 253 253 000 - 0 197 Current_Pending_Sector ---R-- 253 253 000 - 0 198 Offline_Uncorrectable ---R-- 253 253 000 - 0 199 UDMA_CRC_Error_Count ---R-- 199 199 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 252 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 252 000 - 0 202 Data_Address_Mark_Errs -O-R-- 253 251 000 - 0 203 Run_Out_Cancel PO-R-- 253 252 180 - 3 204 Soft_ECC_Correction -O-R-- 253 252 000 - 0 205 Thermal_Asperity_Rate -O-R-- 253 252 000 - 0 207 Spin_High_Current -O-R-K 253 252 000 - 0 208 Spin_Buzz -O-R-K 253 252 000 - 0 209 Offline_Seek_Performnce --S--K 240 240 000 - 163 210 Unknown_Attribute -O--CK 253 252 000 - 0 211 Unknown_Attribute -O--CK 253 252 000 - 0 212 Unknown_Attribute -O--CK 253 252 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 4 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log SMART Extended Comprehensive Error Log Version: 1 (4 sectors) Device Error Count: 4 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4 [3] occurred at disk power-on lifetime: 610 hours (25 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 40 01 06 9e 0e 00 00 00 40 00 at LBA = 0x69e0e000000 = 7275909480448 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 00 00 00 01 00 00 00 00 00 00 40 00 00:13:05.201 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:59.070 READ MULTIPLE c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:58.985 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:52.854 READ MULTIPLE c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:52.760 READ MULTIPLE Error 3 [2] occurred at disk power-on lifetime: 610 hours (25 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 40 01 06 9e 0e 00 00 00 40 00 at LBA = 0x69e0e000000 = 7275909480448 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:58.985 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:52.854 READ MULTIPLE c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:52.760 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:46.622 READ MULTIPLE c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:46.538 READ MULTIPLE Error 2 [1] occurred at disk power-on lifetime: 610 hours (25 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 00 01 00 00 00 00 00 00 40 00 at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:52.760 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:46.622 READ MULTIPLE c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:46.538 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:41.388 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d 47 46 00 00:12:41.385 READ MULTIPLE Error 1 [0] occurred at disk power-on lifetime: 610 hours (25 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 00 00 01 00 00 00 00 00 00 40 00 at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 00 00 00 01 00 00 00 00 00 00 40 00 00:12:46.538 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d c7 46 00 00:12:41.388 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9d 47 46 00 00:12:41.385 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9c c7 46 00 00:12:41.381 READ MULTIPLE c4 00 00 00 80 00 00 00 06 9c 47 46 00 00:12:41.378 READ MULTIPLE SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 1 (0x0001) Device State: Active (0) Current Temperature: 42 Celsius Power Cycle Min/Max Temperature: --/42 Celsius Lifetime Min/Max Temperature: --/57 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 0/60 Celsius Temperature History Size (Index): 478 (477) Index Estimated Time Temperature Celsius 0 2020-09-20 03:57 44 ************************* ... ..( 33 skipped). .. ************************* 34 2020-09-20 04:31 44 ************************* 35 2020-09-20 04:32 ? - 36 2020-09-20 04:33 44 ************************* 37 2020-09-20 04:34 ? - 38 2020-09-20 04:35 44 ************************* ... ..( 4 skipped). .. ************************* 43 2020-09-20 04:40 44 ************************* 44 2020-09-20 04:41 43 ************************ ... ..( 6 skipped). .. ************************ 51 2020-09-20 04:48 43 ************************ 52 2020-09-20 04:49 44 ************************* 53 2020-09-20 04:50 43 ************************ 54 2020-09-20 04:51 43 ************************ 55 2020-09-20 04:52 44 ************************* ... ..( 5 skipped). .. ************************* 61 2020-09-20 04:58 44 ************************* 62 2020-09-20 04:59 43 ************************ ... ..( 6 skipped). .. ************************ 69 2020-09-20 05:06 43 ************************ 70 2020-09-20 05:07 ? - 71 2020-09-20 05:08 43 ************************ 72 2020-09-20 05:09 ? - 73 2020-09-20 05:10 43 ************************ 74 2020-09-20 05:11 44 ************************* 75 2020-09-20 05:12 ? - 76 2020-09-20 05:13 44 ************************* 77 2020-09-20 05:14 ? - 78 2020-09-20 05:15 44 ************************* ... ..( 2 skipped). .. ************************* 81 2020-09-20 05:18 44 ************************* 82 2020-09-20 05:19 ? - 83 2020-09-20 05:20 44 ************************* 84 2020-09-20 05:21 ? - 85 2020-09-20 05:22 44 ************************* ... ..( 36 skipped). .. ************************* 122 2020-09-20 05:59 44 ************************* 123 2020-09-20 06:00 ? - 124 2020-09-20 06:01 44 ************************* 125 2020-09-20 06:02 ? - 126 2020-09-20 06:03 44 ************************* ... ..( 9 skipped). .. ************************* 136 2020-09-20 06:13 44 ************************* 137 2020-09-20 06:14 43 ************************ 138 2020-09-20 06:15 43 ************************ 139 2020-09-20 06:16 44 ************************* 140 2020-09-20 06:17 44 ************************* 141 2020-09-20 06:18 44 ************************* 142 2020-09-20 06:19 43 ************************ 143 2020-09-20 06:20 ? - 144 2020-09-20 06:21 44 ************************* 145 2020-09-20 06:22 ? - 146 2020-09-20 06:23 44 ************************* 147 2020-09-20 06:24 43 ************************ 148 2020-09-20 06:25 44 ************************* ... ..( 20 skipped). .. ************************* 169 2020-09-20 06:46 44 ************************* 170 2020-09-20 06:47 46 *************************** 171 2020-09-20 06:48 44 ************************* 172 2020-09-20 06:49 44 ************************* 173 2020-09-20 06:50 46 *************************** ... ..( 48 skipped). .. *************************** 222 2020-09-20 07:39 46 *************************** 223 2020-09-20 07:40 ? - 224 2020-09-20 07:41 46 *************************** 225 2020-09-20 07:42 ? - 226 2020-09-20 07:43 46 *************************** ... ..( 8 skipped). .. *************************** 235 2020-09-20 07:52 46 *************************** 236 2020-09-20 07:53 44 ************************* ... ..( 21 skipped). .. ************************* 258 2020-09-20 08:15 44 ************************* 259 2020-09-20 08:16 43 ************************ ... ..( 15 skipped). .. ************************ 275 2020-09-20 08:32 43 ************************ 276 2020-09-20 08:33 42 *********************** 277 2020-09-20 08:34 42 *********************** 278 2020-09-20 08:35 43 ************************ 279 2020-09-20 08:36 42 *********************** 280 2020-09-20 08:37 43 ************************ 281 2020-09-20 08:38 42 *********************** ... ..( 7 skipped). .. *********************** 289 2020-09-20 08:46 42 *********************** 290 2020-09-20 08:47 43 ************************ ... ..( 2 skipped). .. ************************ 293 2020-09-20 08:50 43 ************************ 294 2020-09-20 08:51 42 *********************** 295 2020-09-20 08:52 43 ************************ ... ..( 73 skipped). .. ************************ 369 2020-09-20 10:06 43 ************************ 370 2020-09-20 10:07 42 *********************** 371 2020-09-20 10:08 42 *********************** 372 2020-09-20 10:09 43 ************************ 373 2020-09-20 10:10 43 ************************ 374 2020-09-20 10:11 42 *********************** 375 2020-09-20 10:12 42 *********************** 376 2020-09-20 10:13 42 *********************** 377 2020-09-20 10:14 ? - 378 2020-09-20 10:15 42 *********************** 379 2020-09-20 10:16 ? - 380 2020-09-20 10:17 42 *********************** 381 2020-09-20 10:18 42 *********************** 382 2020-09-20 10:19 43 ************************ ... ..( 5 skipped). .. ************************ 388 2020-09-20 10:25 43 ************************ 389 2020-09-20 10:26 42 *********************** 390 2020-09-20 10:27 43 ************************ 391 2020-09-20 10:28 42 *********************** ... ..( 3 skipped). .. *********************** 395 2020-09-20 10:32 42 *********************** 396 2020-09-20 10:33 ? - 397 2020-09-20 10:34 42 *********************** 398 2020-09-20 10:35 ? - 399 2020-09-20 10:36 42 *********************** 400 2020-09-20 10:37 43 ************************ ... ..( 10 skipped). .. ************************ 411 2020-09-20 10:48 43 ************************ 412 2020-09-20 10:49 42 *********************** ... ..( 2 skipped). .. *********************** 415 2020-09-20 10:52 42 *********************** 416 2020-09-20 10:53 ? - 417 2020-09-20 10:54 42 *********************** 418 2020-09-20 10:55 ? - 419 2020-09-20 10:56 42 *********************** 420 2020-09-20 10:57 ? - 421 2020-09-20 10:58 42 *********************** 422 2020-09-20 10:59 ? - 423 2020-09-20 11:00 42 *********************** ... ..( 16 skipped). .. *********************** 440 2020-09-20 11:17 42 *********************** 441 2020-09-20 11:18 41 ********************** 442 2020-09-20 11:19 42 *********************** ... ..( 25 skipped). .. *********************** 468 2020-09-20 11:45 42 *********************** 469 2020-09-20 11:46 ? - 470 2020-09-20 11:47 42 *********************** 471 2020-09-20 11:48 ? - 472 2020-09-20 11:49 42 *********************** ... ..( 4 skipped). .. *********************** 477 2020-09-20 11:54 42 *********************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) not supported