/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar Z5K320 Device Model: Hitachi HTS543232A7A384 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ES2OA60W User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 30 13:38:09 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 93) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 197 197 040 - 155 3 Spin_Up_Time POS--- 217 217 033 - 1 4 Start_Stop_Count -O--C- 095 095 000 - 9128 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 112 112 040 - 35 9 Power_On_Hours -O--C- 063 063 000 - 16604 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 095 095 000 - 8914 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 098 098 000 - 490 193 Load_Cycle_Count -O--C- 088 088 000 - 122131 194 Temperature_Celsius -O---- 193 193 000 - 31 (Min/Max 10/50) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 10 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 13 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 13 [0] occurred at disk power-on lifetime: 1371 hours (57 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 07 00 00 Error: ABRT at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 d8 ff 08 08 00 00 00 00 00 00 e0 08 00:02:56.033 READ MULTIPLE c4 d8 ff 08 08 00 00 00 00 00 00 e0 08 00:02:56.030 READ MULTIPLE c4 d8 ff 08 08 00 00 00 00 00 00 e0 08 00:02:56.027 READ MULTIPLE c4 d8 ff 02 08 00 00 00 00 00 00 e0 08 00:02:56.024 READ MULTIPLE c4 d8 ff 01 02 00 00 00 00 00 00 e0 08 00:02:56.007 READ MULTIPLE Error 12 [3] occurred at disk power-on lifetime: 1371 hours (57 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 07 00 00 Error: ABRT at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 d8 ff 08 08 00 00 00 00 00 00 e0 08 00:02:56.027 READ MULTIPLE c4 d8 ff 02 08 00 00 00 00 00 00 e0 08 00:02:56.024 READ MULTIPLE c4 d8 ff 01 02 00 00 00 00 00 00 e0 08 00:02:56.007 READ MULTIPLE c4 d8 ff 02 01 00 00 00 00 00 00 e0 08 00:02:55.997 READ MULTIPLE c4 d8 ff 02 02 00 00 00 00 00 00 e0 08 00:02:55.988 READ MULTIPLE Error 11 [2] occurred at disk power-on lifetime: 1371 hours (57 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 00 00 00 Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.749 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.749 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.735 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.734 READ MULTIPLE c4 d8 ff 08 01 00 00 02 00 00 00 e0 08 00:02:42.734 READ MULTIPLE Error 10 [1] occurred at disk power-on lifetime: 1371 hours (57 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 01 00 00 00 00 00 09 00 00 Error: ABRT at LBA = 0x00000009 = 9 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c4 d8 ff 01 08 00 00 00 00 00 02 e0 08 00:02:42.718 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.718 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.717 READ MULTIPLE c4 d8 ff 01 01 00 00 00 00 00 00 e0 08 00:02:42.716 READ MULTIPLE c4 d8 ff 00 01 c2 4f 00 00 00 00 e0 08 00:02:42.699 READ MULTIPLE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 15060 - # 2 Extended offline Completed without error 00% 14664 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 31 Celsius Power Cycle Min/Max Temperature: 30/33 Celsius Lifetime Min/Max Temperature: 10/50 Celsius Specified Max Operating Temperature: 32 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/65 Celsius Temperature History Size (Index): 128 (112) Index Estimated Time Temperature Celsius 113 2022-01-30 11:31 30 *********** ... ..( 34 skipped). .. *********** 20 2022-01-30 12:06 30 *********** 21 2022-01-30 12:07 31 ************ ... ..( 7 skipped). .. ************ 29 2022-01-30 12:15 31 ************ 30 2022-01-30 12:16 30 *********** 31 2022-01-30 12:17 31 ************ 32 2022-01-30 12:18 30 *********** 33 2022-01-30 12:19 30 *********** 34 2022-01-30 12:20 30 *********** 35 2022-01-30 12:21 31 ************ 36 2022-01-30 12:22 30 *********** ... ..( 8 skipped). .. *********** 45 2022-01-30 12:31 30 *********** 46 2022-01-30 12:32 ? - 47 2022-01-30 12:33 ? - 48 2022-01-30 12:34 ? - 49 2022-01-30 12:35 30 *********** ... ..( 6 skipped). .. *********** 56 2022-01-30 12:42 30 *********** 57 2022-01-30 12:43 31 ************ 58 2022-01-30 12:44 32 ************* 59 2022-01-30 12:45 31 ************ 60 2022-01-30 12:46 32 ************* 61 2022-01-30 12:47 32 ************* 62 2022-01-30 12:48 33 ************** 63 2022-01-30 12:49 32 ************* ... ..( 2 skipped). .. ************* 66 2022-01-30 12:52 32 ************* 67 2022-01-30 12:53 31 ************ ... ..( 6 skipped). .. ************ 74 2022-01-30 13:00 31 ************ 75 2022-01-30 13:01 30 *********** ... ..( 19 skipped). .. *********** 95 2022-01-30 13:21 30 *********** 96 2022-01-30 13:22 31 ************ 97 2022-01-30 13:23 30 *********** ... ..( 3 skipped). .. *********** 101 2022-01-30 13:27 30 *********** 102 2022-01-30 13:28 31 ************ ... ..( 9 skipped). .. ************ 112 2022-01-30 13:38 31 ************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 8914 --- Lifetime Power-On Resets 0x01 0x010 4 16604 --- Power-on Hours 0x01 0x018 6 15283057583 --- Logical Sectors Written 0x01 0x020 6 135533402 --- Number of Write Commands 0x01 0x028 6 18037097498 --- Logical Sectors Read 0x01 0x030 6 277517950 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 13461 --- Spindle Motor Power-on Hours 0x03 0x010 4 13452 --- Head Flying Hours 0x03 0x018 4 122131 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 805 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 3 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 13382 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 31 --- Current Temperature 0x05 0x010 1 28 N-- Average Short Term Temperature 0x05 0x018 1 28 N-- Average Long Term Temperature 0x05 0x020 1 50 --- Highest Temperature 0x05 0x028 1 10 --- Lowest Temperature 0x05 0x030 1 46 N-- Highest Average Short Term Temperature 0x05 0x038 1 24 N-- Lowest Average Short Term Temperature 0x05 0x040 1 41 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 45473 --- Number of Hardware Resets 0x06 0x010 4 10580 --- Number of ASR Events 0x06 0x018 4 10 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 1910 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 38 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Device Model: SSD 120GB Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: FW190424 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jan 30 13:38:11 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Disabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5d) SMART execute Offline immediate. No Auto Offline data collection support. Abort Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 4) minutes. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O--CK 100 100 050 - 0 5 Reallocated_Sector_Ct -O--CK 100 100 050 - 0 9 Power_On_Hours -O--CK 100 100 050 - 2101 12 Power_Cycle_Count -O--CK 100 100 050 - 913 160 Unknown_Attribute -O--CK 100 100 050 - 0 161 Unknown_Attribute -O--CK 100 100 050 - 0 163 Unknown_Attribute -O--CK 100 100 050 - 26 164 Unknown_Attribute -O--CK 100 100 050 - 175168 165 Unknown_Attribute -O--CK 100 100 050 - 52 166 Unknown_Attribute -O--CK 100 100 050 - 16 167 Unknown_Attribute -O--CK 100 100 050 - 33 168 Unknown_Attribute -O--CK 100 100 050 - 0 169 Unknown_Attribute -O--CK 100 100 050 - 0 175 Program_Fail_Count_Chip -O--CK 100 100 050 - 0 176 Erase_Fail_Count_Chip -O--CK 100 100 050 - 79935 177 Wear_Leveling_Count -O--CK 100 100 050 - 373737 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 050 - 0 181 Program_Fail_Cnt_Total -O--CK 100 100 050 - 0 182 Erase_Fail_Count_Total -O--CK 100 100 050 - 0 192 Power-Off_Retract_Count -O--CK 100 100 050 - 28 194 Temperature_Celsius -O--CK 100 100 050 - 40 195 Hardware_ECC_Recovered -O--CK 100 100 050 - 0 212 Unknown_Attribute -O--CK 100 100 050 - 0 197 Current_Pending_Sector -O--CK 100 100 050 - 0 198 Offline_Uncorrectable -O--CK 100 100 050 - 0 199 UDMA_CRC_Error_Count -O--CK 100 100 050 - 0 232 Available_Reservd_Space -O--CK 100 100 050 - 0 241 Total_LBAs_Written -O--CK 100 100 050 - 31471 242 Total_LBAs_Read -O--CK 100 100 050 - 27601 249 Unknown_Attribute -O--CK 100 100 050 - 34990 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 16 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 0 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Offline Completed without error 00% 2001 - # 2 Offline Self-test routine in progress 10% 2001 - # 3 Offline Self-test routine in progress 10% 2001 - # 4 Offline Self-test routine in progress 10% 2001 - # 5 Offline Self-test routine in progress 10% 2001 - # 6 Offline Self-test routine in progress 10% 2001 - # 7 Offline Self-test routine in progress 10% 2001 - # 8 Offline Self-test routine in progress 10% 2001 - # 9 Offline Self-test routine in progress 10% 2001 - #10 Offline Self-test routine in progress 10% 2001 - #11 Offline Self-test routine in progress 10% 2001 - #12 Offline Self-test routine in progress 10% 2001 - #13 Offline Self-test routine in progress 10% 2001 - #14 Offline Self-test routine in progress 10% 2001 - #15 Offline Self-test routine in progress 10% 2001 - #16 Offline Self-test routine in progress 10% 2001 - #17 Offline Self-test routine in progress 10% 2001 - #18 Offline Self-test routine in progress 10% 2001 - #19 Offline Self-test routine in progress 10% 2001 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 913 --- Lifetime Power-On Resets 0x01 0x010 4 2101 --- Power-on Hours 0x01 0x018 6 2062483456 --- Logical Sectors Written 0x01 0x020 6 23941297 --- Number of Write Commands 0x01 0x028 6 1808859136 --- Logical Sectors Read 0x01 0x030 6 26148252 --- Number of Read Commands |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0009 4 1038 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2896 Device-to-host register FISes sent due to a COMRESET 0x000b 4 0 CRC errors within host-to-device FIS 0x000d 4 0 Non-CRC errors within host-to-device FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P120 Device Model: SAMSUNG SP2004C Serial Number: -- Firmware Version: VM100-41 User Capacity: 200,049,647,616 bytes [200 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a Local Time is: Sun Jan 30 13:38:11 2022 CET ==> WARNING: May need -F samsung3 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 121) The previous self-test completed having the read element of the test failed. Total time to complete Offline data collection: ( 4907) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 81) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 253 100 051 - 0 3 Spin_Up_Time POS--- 100 100 025 - 4480 4 Start_Stop_Count -O--CK 085 085 000 - 15798 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 1 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 253 253 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 22419 10 Spin_Retry_Count PO--CK 253 253 051 - 0 11 Calibration_Retry_Count -O--C- 253 100 000 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 8189 187 Reported_Uncorrect -O--CK 001 001 000 - 396021 190 Airflow_Temperature_Cel -O---K 115 082 000 - 41 194 Temperature_Celsius -O---K 115 082 000 - 41 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 9902 196 Reallocated_Event_Count -O--CK 100 100 000 - 1 197 Current_Pending_Sector -O--C- 100 100 000 - 2 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 253 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 100 000 - 39 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x01) instead Device Error Count: 42697 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 42697 [0] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:43.500 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:41.750 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:41.750 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:41.750 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:41.750 SET FEATURES [Set transfer mode] Error 42696 [7] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:41.688 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:39.938 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:39.938 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:39.938 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:39.938 SET FEATURES [Set transfer mode] Error 42695 [6] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:39.750 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:38.063 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:38.063 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:38.063 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:38.000 SET FEATURES [Set transfer mode] Error 42694 [5] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:37.938 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:36.250 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:36.250 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:36.250 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:36.188 SET FEATURES [Set transfer mode] Error 42693 [4] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:36.125 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:34.375 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:34.375 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:34.375 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:34.375 SET FEATURES [Set transfer mode] Error 42692 [3] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:34.313 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:32.563 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:32.563 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:32.563 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:32.563 SET FEATURES [Set transfer mode] Error 42691 [2] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:32.500 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:30.750 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:30.750 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:30.750 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:30.750 SET FEATURES [Set transfer mode] Error 42690 [1] occurred at disk power-on lifetime: 20103 hours (837 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 17 40 00 00 eb 00 Error: UNC 8 sectors at LBA = 0x1f400000 = 524288000 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 10 00 00 08 00 00 00 17 40 00 eb 00 00:58:30.563 READ DMA ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:58:28.875 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:58:28.875 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 03 00 00 00 00 00 00 00 00 00 a0 00 00:58:28.875 IDENTIFY DEVICE ef 10 03 00 46 00 00 00 00 00 00 a0 00 00:58:28.813 SET FEATURES [Set transfer mode] SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 22319 186073092 # 2 Extended offline Completed: read failure 90% 20868 186073092 # 3 Extended offline Completed: read failure 90% 20528 186073092 # 4 Extended offline Completed: read failure 90% 20470 186073092 # 5 Short offline Completed: read failure 90% 20174 186073092 # 6 Extended offline Completed: read failure 90% 20150 186073092 # 7 Short offline Completed without error 00% 17740 - # 8 Short offline Completed without error 00% 8322 - # 9 Short offline Completed: read failure 90% 321 313542809 SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: --/42 Celsius Lifetime Min/Max Temperature: --/52 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/55 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (28) Index Estimated Time Temperature Celsius 29 2022-01-30 11:31 42 *********************** ... ..( 60 skipped). .. *********************** 90 2022-01-30 12:32 42 *********************** 91 2022-01-30 12:33 ? - 92 2022-01-30 12:34 42 *********************** ... ..( 15 skipped). .. *********************** 108 2022-01-30 12:50 42 *********************** 109 2022-01-30 12:51 41 ********************** 110 2022-01-30 12:52 42 *********************** 111 2022-01-30 12:53 41 ********************** ... ..( 44 skipped). .. ********************** 28 2022-01-30 13:38 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 45 Device-to-host register FISes sent due to a COMRESET 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 7 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x8001 2 0 Vendor specific /dev/sdd === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD2500AAJS-75B4A0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.03A01 User Capacity: 250,000,000,000 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sun Jan 30 13:38:12 2022 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5280) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 65) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 156 153 021 - 3200 4 Start_Stop_Count -O--CK 094 094 000 - 6518 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10888 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 094 094 000 - 6518 192 Power-Off_Retract_Count -O--CK 200 200 000 - 490 193 Load_Cycle_Count -O--CK 198 198 000 - 6518 194 Temperature_Celsius -O---K 100 095 000 - 43 196 Reallocated_Event_Count -O--CK 199 199 000 - 1 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 086 086 000 - 10664 241 Total_LBAs_Written -O--CK 200 200 000 - 5986340363 242 Total_LBAs_Read -O--CK 200 200 000 - 6846743759 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 10790 - # 2 Extended offline Completed without error 00% 9351 - # 3 Offline Completed without error 00% 9015 - # 4 Extended offline Completed without error 00% 8957 - # 5 Offline Completed without error 00% 8641 - # 6 Short offline Completed without error 00% 8614 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 43/43 Celsius Lifetime Min/Max Temperature: 21/48 Celsius Specified Max Operating Temperature: 31 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (100) Index Estimated Time Temperature Celsius 101 2022-01-30 11:31 43 ************************ ... ..( 59 skipped). .. ************************ 33 2022-01-30 12:31 43 ************************ 34 2022-01-30 12:32 ? - 35 2022-01-30 12:33 43 ************************ 36 2022-01-30 12:34 43 ************************ 37 2022-01-30 12:35 ? - 38 2022-01-30 12:36 43 ************************ 39 2022-01-30 12:37 ? - 40 2022-01-30 12:38 43 ************************ ... ..( 59 skipped). .. ************************ 100 2022-01-30 13:38 43 ************************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 44 Device-to-host register FISes sent due to a COMRESET 0x8000 4 3905 Vendor specific