/dev/sda === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA050 Serial Number: -- LU WWN Device Id: 5 000039 ... Firmware Version: MS1OA750 User Capacity: 500,103,634,432 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Apr 20 08:50:56 2018 +03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3594) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 60) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 142 142 054 - 70 3 Spin_Up_Time POS--- 124 124 024 - 185 (Average 185) 4 Start_Stop_Count -O--C- 100 100 000 - 1895 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 113 113 020 - 35 9 Power_On_Hours -O--C- 099 099 000 - 7071 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 1470 192 Power-Off_Retract_Count -O--CK 099 099 000 - 1901 193 Load_Cycle_Count -O--C- 099 099 000 - 1901 194 Temperature_Celsius -O---- 133 133 000 - 45 (Min/Max 22/54) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 61594 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL R/O 7 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x08 GPL R/O 2 Power Conditions log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 65535 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 65535 [3] occurred at disk power-on lifetime: 7036 hours (293 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 10 07 00 00 Error: UNC at LBA = 0x00001007 = 4103 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 20 00 00 00 00 10 00 40 08 12:04:43.506 READ FPDMA QUEUED 60 00 58 00 18 00 00 3a 38 3d a8 40 08 12:04:43.505 READ FPDMA QUEUED 60 00 50 00 10 00 00 3a 38 3d 50 40 08 12:04:43.505 READ FPDMA QUEUED 60 00 30 00 08 00 00 3a 38 3d 18 40 08 12:04:43.505 READ FPDMA QUEUED 60 00 10 00 00 00 00 3a 38 3d 00 40 08 12:04:43.505 READ FPDMA QUEUED Error 65534 [2] occurred at disk power-on lifetime: 7034 hours (293 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 1d 5a 28 07 0d 00 Error: UNC at LBA = 0x1d5a2807 = 492447751 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 88 00 00 1d 5a 28 00 40 08 09:54:11.608 READ FPDMA QUEUED 60 00 08 00 80 00 00 3a 38 34 e8 40 08 09:54:11.600 READ FPDMA QUEUED 60 00 08 00 78 00 00 3a 38 28 e8 40 08 09:54:11.578 READ FPDMA QUEUED 60 00 08 00 70 00 00 3a 38 31 40 40 08 09:54:11.578 READ FPDMA QUEUED 60 00 08 00 68 00 00 3a 38 31 18 40 08 09:54:11.578 READ FPDMA QUEUED Error 65533 [1] occurred at disk power-on lifetime: 6762 hours (281 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 00 10 07 00 00 Error: UNC at LBA = 0x00001007 = 4103 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 f0 00 00 00 00 10 00 40 08 04:13:25.346 READ FPDMA QUEUED 60 00 58 00 e8 00 00 3a 38 3d a8 40 08 04:13:25.345 READ FPDMA QUEUED 60 00 50 00 e0 00 00 3a 38 3d 50 40 08 04:13:25.345 READ FPDMA QUEUED 60 00 30 00 d8 00 00 3a 38 3d 18 40 08 04:13:25.344 READ FPDMA QUEUED 60 00 a8 00 d0 00 00 3a 38 3c 68 40 08 04:13:25.344 READ FPDMA QUEUED Error 65532 [0] occurred at disk power-on lifetime: 6756 hours (281 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 60 08 07 00 00 Error: UNC at LBA = 0x00600807 = 6293511 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 30 00 00 00 60 08 00 40 08 09:34:32.187 READ FPDMA QUEUED 60 00 68 00 28 00 00 1d 1e 87 88 40 08 09:34:32.186 READ FPDMA QUEUED 60 00 80 00 20 00 00 1d 1e 87 00 40 08 09:34:32.186 READ FPDMA QUEUED 60 00 f8 00 18 00 00 1d 1e 86 00 40 08 09:34:32.186 READ FPDMA QUEUED 60 02 00 00 10 00 00 1d 1e 84 00 40 08 09:34:32.160 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5195 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 45 Celsius Power Cycle Min/Max Temperature: 27/45 Celsius Lifetime Min/Max Temperature: 22/54 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (96) Index Estimated Time Temperature Celsius 97 2018-04-20 06:43 36 ***************** 98 2018-04-20 06:44 36 ***************** 99 2018-04-20 06:45 36 ***************** 100 2018-04-20 06:46 37 ****************** 101 2018-04-20 06:47 37 ****************** 102 2018-04-20 06:48 37 ****************** 103 2018-04-20 06:49 38 ******************* ... ..( 3 skipped). .. ******************* 107 2018-04-20 06:53 38 ******************* 108 2018-04-20 06:54 39 ******************** 109 2018-04-20 06:55 39 ******************** 110 2018-04-20 06:56 39 ******************** 111 2018-04-20 06:57 40 ********************* ... ..( 7 skipped). .. ********************* 119 2018-04-20 07:05 40 ********************* 120 2018-04-20 07:06 41 ********************** ... ..( 20 skipped). .. ********************** 13 2018-04-20 07:27 41 ********************** 14 2018-04-20 07:28 42 *********************** 15 2018-04-20 07:29 41 ********************** 16 2018-04-20 07:30 41 ********************** 17 2018-04-20 07:31 41 ********************** 18 2018-04-20 07:32 42 *********************** ... ..( 6 skipped). .. *********************** 25 2018-04-20 07:39 42 *********************** 26 2018-04-20 07:40 41 ********************** 27 2018-04-20 07:41 42 *********************** 28 2018-04-20 07:42 42 *********************** 29 2018-04-20 07:43 41 ********************** 30 2018-04-20 07:44 41 ********************** 31 2018-04-20 07:45 42 *********************** 32 2018-04-20 07:46 41 ********************** 33 2018-04-20 07:47 41 ********************** 34 2018-04-20 07:48 41 ********************** 35 2018-04-20 07:49 42 *********************** 36 2018-04-20 07:50 41 ********************** 37 2018-04-20 07:51 42 *********************** 38 2018-04-20 07:52 42 *********************** 39 2018-04-20 07:53 42 *********************** 40 2018-04-20 07:54 41 ********************** 41 2018-04-20 07:55 41 ********************** 42 2018-04-20 07:56 42 *********************** ... ..( 4 skipped). .. *********************** 47 2018-04-20 08:01 42 *********************** 48 2018-04-20 08:02 43 ************************ ... ..( 4 skipped). .. ************************ 53 2018-04-20 08:07 43 ************************ 54 2018-04-20 08:08 44 ************************* ... ..( 5 skipped). .. ************************* 60 2018-04-20 08:14 44 ************************* 61 2018-04-20 08:15 45 ************************** 62 2018-04-20 08:16 44 ************************* 63 2018-04-20 08:17 45 ************************** ... ..( 32 skipped). .. ************************** 96 2018-04-20 08:50 45 ************************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1470 --- Lifetime Power-On Resets 0x01 0x010 4 7071 --- Power-on Hours 0x01 0x018 6 38166236510 --- Logical Sectors Written 0x01 0x020 6 840021990 --- Number of Write Commands 0x01 0x028 6 152254671986 --- Logical Sectors Read 0x01 0x030 6 886047737 --- Number of Read Commands 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 6749 --- Spindle Motor Power-on Hours 0x03 0x010 4 6749 --- Head Flying Hours 0x03 0x018 4 1901 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 24 --- Read Recovery Attempts 0x03 0x030 4 2 --- Number of Mechanical Start Failures 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 31 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 183 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 45 --- Current Temperature 0x05 0x010 1 44 N-- Average Short Term Temperature 0x05 0x018 1 41 N-- Average Long Term Temperature 0x05 0x020 1 54 --- Highest Temperature 0x05 0x028 1 22 --- Lowest Temperature 0x05 0x030 1 50 N-- Highest Average Short Term Temperature 0x05 0x038 1 25 N-- Lowest Average Short Term Temperature 0x05 0x040 1 45 N-- Highest Average Long Term Temperature 0x05 0x048 1 25 N-- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 60 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 11400 --- Number of Hardware Resets 0x06 0x010 4 8646 --- Number of ASR Events 0x06 0x018 4 61594 --- Number of Interface CRC Errors |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 1 R_ERR response for data FIS 0x0003 2 1 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 10 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 Device Model: ST31000528AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC49 User Capacity: 1,000,200,658,432 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Apr 20 08:50:58 2018 +03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 208 (intermediate), recommended: 208 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 167) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 126205042 3 Spin_Up_Time PO---- 095 093 000 - 0 4 Start_Stop_Count -O--CK 088 088 020 - 12395 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 089 060 030 - 867283790 9 Power_On_Hours -O--CK 074 074 000 - 23403 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4889 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 001 001 099 NOW 202 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 094 000 - 214751642548 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 056 044 045 Past 44 (Min/Max 27/44 #1) 194 Temperature_Celsius -O---K 044 056 000 - 44 (0 18 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 030 021 000 - 126205042 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 162 000 - 106032 240 Head_Flying_Hours ------ 100 253 000 - 38467 (206 76 0) 241 Total_LBAs_Written ------ 100 253 000 - 1398604244 242 Total_LBAs_Read ------ 100 253 000 - 1338285210 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2928 Device vendor specific log 0xbd GPL VS 252 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 248 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 248 [7] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:21.772 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:20.858 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:20.765 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:19.843 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:19.749 READ DMA EXT Error 247 [6] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:20.858 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:20.765 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:19.843 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:19.749 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:18.835 READ DMA EXT Error 246 [5] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:20.765 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:19.843 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:19.749 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:18.835 READ DMA EXT Error 245 [4] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:19.843 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:19.749 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:18.741 READ DMA EXT Error 244 [3] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:19.749 READ DMA EXT 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:18.741 READ DMA EXT Error 243 [2] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 60 a9 80 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:17.819 READ DMA EXT Error 242 [1] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:18.835 READ DMA EXT 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:17.819 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:17.725 READ DMA EXT Error 241 [0] occurred at disk power-on lifetime: 21746 hours (906 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 71 00 04 00 00 00 80 87 81 40 00 Device Fault; Error: ABRT 4 sectors at LBA = 0x00808781 = 8423297 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 74 70 5f ff 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:18.741 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:17.819 READ DMA EXT 25 00 00 00 01 00 00 74 60 c0 00 40 00 00:04:17.725 READ DMA EXT 25 00 00 00 01 00 00 00 00 3f 00 40 00 00:04:16.803 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 13933 - # 2 Short offline Completed without error 00% 1645 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 44 Celsius Power Cycle Min/Max Temperature: 27/44 Celsius Lifetime Min/Max Temperature: 18/56 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (106) Index Estimated Time Temperature Celsius 107 2018-04-15 03:02 ? - 108 2018-04-15 04:01 27 ******** 109 2018-04-15 05:00 27 ******** 110 2018-04-15 05:59 44 ************************* 111 2018-04-15 06:58 44 ************************* 112 2018-04-15 07:57 44 ************************* 113 2018-04-15 08:56 45 ************************** ... ..( 3 skipped). .. ************************** 117 2018-04-15 12:52 45 ************************** 118 2018-04-15 13:51 46 *************************** 119 2018-04-15 14:50 46 *************************** 120 2018-04-15 15:49 ? - 121 2018-04-15 16:48 27 ******** 122 2018-04-15 17:47 ? - 123 2018-04-15 18:46 29 ********** 124 2018-04-15 19:45 29 ********** 125 2018-04-15 20:44 44 ************************* 126 2018-04-15 21:43 43 ************************ ... ..( 2 skipped). .. ************************ 1 2018-04-16 00:40 43 ************************ 2 2018-04-16 01:39 ? - 3 2018-04-16 02:38 31 ************ 4 2018-04-16 03:37 31 ************ 5 2018-04-16 04:36 45 ************************** 6 2018-04-16 05:35 45 ************************** 7 2018-04-16 06:34 44 ************************* 8 2018-04-16 07:33 44 ************************* 9 2018-04-16 08:32 44 ************************* 10 2018-04-16 09:31 ? - 11 2018-04-16 10:30 27 ******** 12 2018-04-16 11:29 27 ******** 13 2018-04-16 12:28 ? - 14 2018-04-16 13:27 27 ******** 15 2018-04-16 14:26 27 ******** 16 2018-04-16 15:25 44 ************************* 17 2018-04-16 16:24 44 ************************* 18 2018-04-16 17:23 45 ************************** 19 2018-04-16 18:22 44 ************************* 20 2018-04-16 19:21 44 ************************* 21 2018-04-16 20:20 45 ************************** 22 2018-04-16 21:19 45 ************************** 23 2018-04-16 22:18 ? - 24 2018-04-16 23:17 27 ******** 25 2018-04-17 00:16 27 ******** 26 2018-04-17 01:15 43 ************************ 27 2018-04-17 02:14 44 ************************* 28 2018-04-17 03:13 44 ************************* 29 2018-04-17 04:12 45 ************************** 30 2018-04-17 05:11 45 ************************** 31 2018-04-17 06:10 45 ************************** 32 2018-04-17 07:09 44 ************************* 33 2018-04-17 08:08 45 ************************** 34 2018-04-17 09:07 46 *************************** 35 2018-04-17 10:06 46 *************************** 36 2018-04-17 11:05 46 *************************** 37 2018-04-17 12:04 ? - 38 2018-04-17 13:03 27 ******** 39 2018-04-17 14:02 27 ******** 40 2018-04-17 15:01 44 ************************* 41 2018-04-17 16:00 ? - 42 2018-04-17 16:59 28 ********* 43 2018-04-17 17:58 28 ********* 44 2018-04-17 18:57 44 ************************* 45 2018-04-17 19:56 45 ************************** 46 2018-04-17 20:55 46 *************************** ... ..( 2 skipped). .. *************************** 49 2018-04-17 23:52 46 *************************** 50 2018-04-18 00:51 45 ************************** 51 2018-04-18 01:50 45 ************************** 52 2018-04-18 02:49 45 ************************** 53 2018-04-18 03:48 ? - 54 2018-04-18 04:47 27 ******** 55 2018-04-18 05:46 28 ********* 56 2018-04-18 06:45 44 ************************* 57 2018-04-18 07:44 45 ************************** 58 2018-04-18 08:43 45 ************************** 59 2018-04-18 09:42 44 ************************* 60 2018-04-18 10:41 44 ************************* 61 2018-04-18 11:40 45 ************************** 62 2018-04-18 12:39 46 *************************** 63 2018-04-18 13:38 47 **************************** 64 2018-04-18 14:37 46 *************************** 65 2018-04-18 15:36 45 ************************** ... ..( 3 skipped). .. ************************** 69 2018-04-18 19:32 45 ************************** 70 2018-04-18 20:31 ? - 71 2018-04-18 21:30 28 ********* 72 2018-04-18 22:29 28 ********* 73 2018-04-18 23:28 44 ************************* 74 2018-04-19 00:27 45 ************************** ... ..( 2 skipped). .. ************************** 77 2018-04-19 03:24 45 ************************** 78 2018-04-19 04:23 46 *************************** 79 2018-04-19 05:22 47 **************************** 80 2018-04-19 06:21 47 **************************** 81 2018-04-19 07:20 47 **************************** 82 2018-04-19 08:19 46 *************************** 83 2018-04-19 09:18 45 ************************** 84 2018-04-19 10:17 45 ************************** 85 2018-04-19 11:16 46 *************************** 86 2018-04-19 12:15 ? - 87 2018-04-19 13:14 28 ********* 88 2018-04-19 14:13 28 ********* 89 2018-04-19 15:12 45 ************************** ... ..( 2 skipped). .. ************************** 92 2018-04-19 18:09 45 ************************** 93 2018-04-19 19:08 46 *************************** ... ..( 3 skipped). .. *************************** 97 2018-04-19 23:04 46 *************************** 98 2018-04-20 00:03 45 ************************** 99 2018-04-20 01:02 45 ************************** 100 2018-04-20 02:01 44 ************************* 101 2018-04-20 03:00 45 ************************** 102 2018-04-20 03:59 ? - 103 2018-04-20 04:58 27 ******** 104 2018-04-20 05:57 27 ******** 105 2018-04-20 06:56 43 ************************ 106 2018-04-20 07:55 44 ************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar P7K500 Device Model: Hitachi HDP725032GLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: GM3OA52A User Capacity: 320,071,851,520 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Apr 20 08:50:59 2018 +03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5908) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 98) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 129 129 054 - 159 3 Spin_Up_Time POS--- 118 118 024 - 325 (Average 327) 4 Start_Stop_Count -O--C- 099 099 000 - 4717 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 131 131 020 - 29 9 Power_On_Hours -O--C- 098 098 000 - 16143 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3867 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4775 193 Load_Cycle_Count -O--C- 097 097 000 - 4775 194 Temperature_Celsius -O---- 139 139 000 - 43 (Min/Max 2/63) 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 505 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 558 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 558 [1] occurred at disk power-on lifetime: 11650 hours (485 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 ff ac 00 00 02 b0 ab db e2 00 Error: UNC at LBA = 0x02b0abdb = 45132763 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 29 03 ff 00 40 00 00 02 b0 ab 47 e0 00 00:01:38.900 READ MULTIPLE EXT ef ff 03 0c 46 00 00 00 00 00 01 a0 02 00:01:38.900 SET FEATURES [Set transfer mode] ef ff 03 10 0c 00 00 00 00 00 01 a0 02 00:01:38.900 SET FEATURES [Set transfer mode] c6 d8 ff 3f 10 00 00 0f 00 00 01 a0 02 00:01:38.900 SET MULTIPLE MODE 91 d8 ff 01 3f 00 00 00 00 00 01 af 02 00:01:38.900 INITIALIZE DEVICE PARAMETERS [OBS-6] Error 557 [0] occurred at disk power-on lifetime: 11650 hours (485 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 59 00 00 00 00 02 b0 ab 86 e2 00 Error: ABRT at LBA = 0x02b0ab86 = 45132678 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 29 d8 ff 00 40 00 00 02 b0 ab 47 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 00 60 42 27 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 a1 a7 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 a1 d7 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 9f b7 e0 00 00:01:29.100 READ MULTIPLE EXT Error 556 [3] occurred at disk power-on lifetime: 11650 hours (485 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 00 40 00 00 02 b0 ab 47 e0 00 Error: at LBA = 0x02b0ab47 = 45132615 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 29 d8 ff 00 40 00 00 02 b0 ab 47 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 00 60 42 27 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 a1 a7 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 a1 d7 e0 00 00:01:29.100 READ MULTIPLE EXT 29 d8 ff 00 08 00 00 02 b0 9f b7 e0 00 00:01:29.100 READ MULTIPLE EXT Error 555 [2] occurred at disk power-on lifetime: 11650 hours (485 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 30 00 00 02 b1 49 cf e2 00 Error: ICRC, ABRT 48 sectors at LBA = 0x02b149cf = 45173199 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 d8 ff 00 40 00 00 02 b1 49 bf e0 00 00:01:29.100 READ DMA EXT 25 d8 ff 00 40 00 00 02 b1 49 7f e0 00 00:01:29.100 READ DMA EXT 25 d8 ff 00 40 00 00 02 b1 49 3f e0 00 00:01:29.100 READ DMA EXT 25 d8 ff 00 08 00 00 00 00 00 57 e0 00 00:01:29.100 READ DMA EXT 25 d8 ff 00 08 00 00 00 60 0d 8f e0 00 00:01:29.100 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Min/Max Temperature: 26/43 Celsius Lifetime Min/Max Temperature: 2/63 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2018-04-20 06:43 33 ************** 115 2018-04-20 06:44 34 *************** 116 2018-04-20 06:45 34 *************** 117 2018-04-20 06:46 35 **************** ... ..( 2 skipped). .. **************** 120 2018-04-20 06:49 35 **************** 121 2018-04-20 06:50 36 ***************** 122 2018-04-20 06:51 36 ***************** 123 2018-04-20 06:52 36 ***************** 124 2018-04-20 06:53 37 ****************** 125 2018-04-20 06:54 37 ****************** 126 2018-04-20 06:55 37 ****************** 127 2018-04-20 06:56 38 ******************* ... ..( 2 skipped). .. ******************* 2 2018-04-20 06:59 38 ******************* 3 2018-04-20 07:00 39 ******************** ... ..( 4 skipped). .. ******************** 8 2018-04-20 07:05 39 ******************** 9 2018-04-20 07:06 40 ********************* ... ..( 7 skipped). .. ********************* 17 2018-04-20 07:14 40 ********************* 18 2018-04-20 07:15 41 ********************** ... ..( 10 skipped). .. ********************** 29 2018-04-20 07:26 41 ********************** 30 2018-04-20 07:27 42 *********************** ... ..( 53 skipped). .. *********************** 84 2018-04-20 08:21 42 *********************** 85 2018-04-20 08:22 43 ************************ 86 2018-04-20 08:23 42 *********************** 87 2018-04-20 08:24 43 ************************ 88 2018-04-20 08:25 42 *********************** 89 2018-04-20 08:26 42 *********************** 90 2018-04-20 08:27 43 ************************ ... ..( 17 skipped). .. ************************ 108 2018-04-20 08:45 43 ************************ 109 2018-04-20 08:46 42 *********************** 110 2018-04-20 08:47 43 ************************ ... ..( 2 skipped). .. ************************ 113 2018-04-20 08:50 43 ************************ SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS