/dev/sda smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-42-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: PNY CS1311 32GB SSD Serial Number: -- LU WWN Device Id: 5 000000 ... Firmware Version: S9FM02.8 User Capacity: 32,017,047,552 bytes [32.0 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-3 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Dec 6 17:46:40 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 2) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate -O-R-- 100 100 000 - 0 9 Power_On_Hours -O--C- 100 100 000 - 241 12 Power_Cycle_Count -O--C- 100 100 000 - 227 168 Unknown_Attribute -O--C- 100 100 000 - 0 170 Unknown_Attribute PO--C- 100 100 010 - 16 173 Unknown_Attribute ------ 100 100 000 - 12124176 192 Power-Off_Retract_Count -O--C- 100 100 000 - 1 194 Temperature_Celsius PO---K 070 070 000 - 30 196 Reallocated_Event_Count ------ 100 100 000 - 0 218 Unknown_Attribute ------ 100 100 000 - 94 241 Total_LBAs_Written -O--C- 100 100 000 - 265513 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 51 Comprehensive SMART error log 0x03 GPL R/O 64 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (64 sectors) Device Error Count: 94 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 94 [93] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3d ef e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053def = 343535 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3d ef e0 00 00:01:28.960 READ DMA EXT 25 00 03 00 7f 00 00 00 00 08 ee e0 00 00:01:28.938 READ DMA EXT 25 00 03 00 02 00 00 00 05 3d 5a e0 00 00:01:28.935 READ DMA EXT 25 00 03 00 01 00 00 00 05 3d 6f e0 00 00:01:28.922 READ DMA EXT 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.916 READ DMA EXT Error 93 [92] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3c f1 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053cf1 = 343281 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.916 READ DMA EXT 25 00 03 00 02 00 00 00 05 3d 50 e0 00 00:01:28.913 READ DMA EXT 25 00 03 00 01 00 00 00 05 3d 6f e0 00 00:01:28.900 READ DMA EXT 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.894 READ DMA EXT 25 00 03 00 7f 00 00 00 00 07 f0 e0 00 00:01:28.890 READ DMA EXT Error 92 [91] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3c f1 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053cf1 = 343281 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.894 READ DMA EXT 25 00 03 00 7f 00 00 00 00 07 f0 e0 00 00:01:28.890 READ DMA EXT 25 00 03 00 7f 00 00 00 00 00 00 e0 00 00:01:28.885 READ DMA EXT 25 00 03 00 01 00 00 00 00 3f 00 e0 00 00:01:28.708 READ DMA EXT 25 00 03 00 7f 00 00 00 00 3e 82 e0 00 00:01:28.703 READ DMA EXT Error 91 [90] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 00 3e 82 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00003e82 = 16002 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 00 3e 82 e0 00 00:01:28.703 READ DMA EXT 25 00 03 00 7f 00 00 00 00 3e 03 e0 00 00:01:28.699 READ DMA EXT 25 00 03 00 7f 00 00 00 00 3d 84 e0 00 00:01:28.694 READ DMA EXT 25 00 03 00 7f 00 00 00 00 3d 05 e0 00 00:01:28.690 READ DMA EXT 25 00 03 00 01 00 00 00 00 3d 38 e0 00 00:01:28.687 READ DMA EXT Error 90 [89] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 00 3d 05 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00003d05 = 15621 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 00 3d 05 e0 00 00:01:28.668 READ DMA EXT 25 00 03 00 02 00 00 00 05 3e 02 e0 00 00:01:28.665 READ DMA EXT 25 00 03 00 01 00 00 00 05 3e 6d e0 00 00:01:28.651 READ DMA EXT 25 00 03 00 7f 00 00 00 05 3d ef e0 00 00:01:28.646 READ DMA EXT 25 00 03 00 7f 00 00 00 00 08 ee e0 00 00:01:28.624 READ DMA EXT Error 89 [88] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3d ef e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053def = 343535 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3d ef e0 00 00:01:28.646 READ DMA EXT 25 00 03 00 7f 00 00 00 00 08 ee e0 00 00:01:28.624 READ DMA EXT 25 00 03 00 02 00 00 00 05 3d 5a e0 00 00:01:28.621 READ DMA EXT 25 00 03 00 01 00 00 00 05 3d 6f e0 00 00:01:28.607 READ DMA EXT 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.602 READ DMA EXT Error 88 [87] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3c f1 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053cf1 = 343281 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.602 READ DMA EXT 25 00 03 00 02 00 00 00 05 3d 50 e0 00 00:01:28.599 READ DMA EXT 25 00 03 00 01 00 00 00 05 3d 6f e0 00 00:01:28.585 READ DMA EXT 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.580 READ DMA EXT 25 00 03 00 7f 00 00 00 00 07 f0 e0 00 00:01:28.575 READ DMA EXT Error 87 [86] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 7f 00 00 00 05 3c f1 e0 00 Error: ICRC, ABRT 127 sectors at LBA = 0x00053cf1 = 343281 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 03 00 7f 00 00 00 05 3c f1 e0 00 00:01:28.580 READ DMA EXT 25 00 03 00 7f 00 00 00 00 07 f0 e0 00 00:01:28.575 READ DMA EXT 25 00 03 00 7f 00 00 00 00 00 00 e0 00 00:01:28.571 READ DMA EXT 25 00 03 00 7f 00 00 00 00 07 f0 e0 00 00:01:28.558 READ DMA EXT 25 00 03 00 7f 00 00 00 00 00 00 e0 00 00:01:28.554 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 4 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 4 2 Device-to-host register FISes sent due to a COMRESET 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb smartctl 6.6 2016-05-31 r4324 [x86_64-linux-5.4.0-42-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD322HJ Serial Number: -- LU WWN Device Id: 5 0000f0 ... Firmware Version: 1AC01113 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Sun Dec 6 17:46:40 2020 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 3773) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 64) minutes. Conveyance self-test routine recommended polling time: ( 8) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 100 051 - 0 3 Spin_Up_Time POS--- 093 093 011 - 2920 4 Start_Stop_Count -O--CK 097 097 000 - 2933 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 253 253 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 9578 9 Power_On_Hours -O--CK 099 099 000 - 5964 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 8 12 Power_Cycle_Count -O--CK 097 097 000 - 2925 13 Read_Soft_Error_Rate -OSR-- 100 100 000 - 0 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 090 065 000 - 10 (Min/Max 10/10) 194 Temperature_Celsius -O---K 088 064 000 - 12 (Min/Max 10/12) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 8148 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 100 099 000 - 103 200 Multi_Zone_Error_Rate -O-R-- 099 099 000 - 82 201 Soft_Read_Error_Rate -O-R-- 253 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x04 GPL R/O 2 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 2 Write stream error log 0x22 GPL R/O 2 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 229 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 229 [4] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 63 00 00 12 84 11 85 e0 00 Error: ICRC, ABRT 99 sectors at LBA = 0x12841185 = 310645125 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 68 00 00 12 84 11 80 e0 0a 00:05:11.690 WRITE DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 0a 00:05:11.690 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 0a 00:05:11.670 IDENTIFY DEVICE ef 00 03 00 42 00 00 00 00 00 00 a0 0a 00:05:11.670 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 0a 00:05:11.670 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 228 [3] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 66 00 00 12 84 11 82 e0 00 Error: ICRC, ABRT 102 sectors at LBA = 0x12841182 = 310645122 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 68 00 00 12 84 11 80 e0 0a 00:05:11.170 WRITE DMA EXT 25 00 00 00 10 00 00 1d cd 08 48 e0 0a 00:05:11.150 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 0a 00:05:11.150 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 0a 00:05:11.130 IDENTIFY DEVICE ef 00 03 00 42 00 00 00 00 00 00 a0 0a 00:05:11.130 SET FEATURES [Set transfer mode] Error 227 [2] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 63 00 00 12 84 11 85 e0 00 Error: ICRC, ABRT 99 sectors at LBA = 0x12841185 = 310645125 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 68 00 00 12 84 11 80 e0 0a 00:05:10.610 WRITE DMA EXT 35 00 00 00 10 00 00 17 df 28 d0 e0 0a 00:05:10.610 WRITE DMA EXT 25 00 00 00 08 00 00 17 85 e8 d0 e0 0a 00:05:10.590 READ DMA EXT 25 00 00 00 10 00 00 1d cd 59 b8 e0 0a 00:05:10.580 READ DMA EXT 25 00 00 00 08 00 00 17 81 09 80 e0 0a 00:05:10.580 READ DMA EXT Error 226 [1] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 27 00 00 17 85 55 39 e0 00 Error: ICRC, ABRT 39 sectors at LBA = 0x17855539 = 394614073 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 30 00 00 17 85 55 30 e0 0a 00:05:06.730 WRITE DMA EXT 25 00 00 00 08 00 00 17 81 16 60 e0 0a 00:05:06.720 READ DMA EXT 25 00 00 00 08 00 00 17 81 0e 48 e0 0a 00:05:06.720 READ DMA EXT 25 00 00 00 08 00 00 17 81 13 60 e0 0a 00:05:06.720 READ DMA EXT 25 00 00 00 08 00 00 17 81 0e b0 e0 0a 00:05:06.720 READ DMA EXT Error 225 [0] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 58 00 0d 00 00 12 84 10 1b e0 00 13 sectors at LBA = 0x1284101b = 310644763 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 70 00 00 12 84 0f b8 e0 0a 00:04:34.800 WRITE DMA EXT 25 00 00 00 08 00 00 17 81 13 38 e0 0a 00:04:34.800 READ DMA EXT 25 00 00 00 08 00 00 17 81 0a e8 e0 0a 00:04:34.790 READ DMA EXT 25 00 00 00 08 00 00 1a 41 17 b0 e0 0a 00:04:34.780 READ DMA EXT 35 00 00 00 30 00 00 17 e5 f8 38 e0 0a 00:04:34.780 WRITE DMA EXT Error 224 [7] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 27 00 00 17 e5 f8 41 e0 00 Error: ICRC, ABRT 39 sectors at LBA = 0x17e5f841 = 400947265 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 30 00 00 17 e5 f8 38 e0 0a 00:04:34.210 WRITE DMA EXT 25 00 00 00 08 00 00 17 81 12 e8 e0 0a 00:04:34.210 READ DMA EXT 25 00 00 00 08 00 00 17 81 13 50 e0 0a 00:04:34.210 READ DMA EXT 25 00 00 00 08 00 00 17 81 1a 28 e0 0a 00:04:34.210 READ DMA EXT 25 00 00 00 08 00 00 17 8e f8 60 e0 0a 00:04:34.210 READ DMA EXT Error 223 [6] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 58 00 46 00 00 12 84 0d 92 e0 00 70 sectors at LBA = 0x12840d92 = 310644114 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 58 00 00 12 84 0d 80 e0 0a 00:04:02.950 WRITE DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 0a 00:04:02.950 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 0a 00:04:02.930 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 0a 00:04:02.930 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 0a 00:04:02.930 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 222 [5] occurred at disk power-on lifetime: 5757 hours (239 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 03 00 00 12 84 0d 7d e0 00 Error: ICRC, ABRT 3 sectors at LBA = 0x12840d7d = 310644093 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 12 84 0d 78 e0 0a 00:03:30.650 WRITE DMA EXT ea 00 00 00 00 00 00 00 84 0d 77 a0 0a 00:03:30.620 FLUSH CACHE EXT 35 00 00 00 68 00 00 12 84 0d 10 e0 0a 00:03:30.620 WRITE DMA EXT 25 00 00 00 08 00 00 17 81 15 70 e0 0a 00:03:30.620 READ DMA EXT 35 00 00 00 30 00 00 17 89 3c 80 e0 0a 00:03:30.620 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (2 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 2865 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 12 Celsius Power Cycle Max Temperature: 12 Celsius Lifetime Max Temperature: 43 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (6) Index Estimated Time Temperature Celsius 7 2020-12-06 15:39 23 **** ... ..( 40 skipped). .. **** 48 2020-12-06 16:20 23 **** 49 2020-12-06 16:21 24 ***** 50 2020-12-06 16:22 23 **** ... ..( 5 skipped). .. **** 56 2020-12-06 16:28 23 **** 57 2020-12-06 16:29 24 ***** ... ..( 2 skipped). .. ***** 60 2020-12-06 16:32 24 ***** 61 2020-12-06 16:33 9 - 62 2020-12-06 16:34 9 - 63 2020-12-06 16:35 10 - 64 2020-12-06 16:36 11 - 65 2020-12-06 16:37 11 - 66 2020-12-06 16:38 12 - 67 2020-12-06 16:39 13 - 68 2020-12-06 16:40 13 - 69 2020-12-06 16:41 14 - 70 2020-12-06 16:42 14 - 71 2020-12-06 16:43 15 - 72 2020-12-06 16:44 15 - 73 2020-12-06 16:45 16 - 74 2020-12-06 16:46 16 - 75 2020-12-06 16:47 17 - ... ..( 2 skipped). .. - 78 2020-12-06 16:50 17 - 79 2020-12-06 16:51 18 - ... ..( 2 skipped). .. - 82 2020-12-06 16:54 18 - 83 2020-12-06 16:55 19 - ... ..( 2 skipped). .. - 86 2020-12-06 16:58 19 - 87 2020-12-06 16:59 20 * ... ..( 5 skipped). .. * 93 2020-12-06 17:05 20 * 94 2020-12-06 17:06 21 ** ... ..( 15 skipped). .. ** 110 2020-12-06 17:22 21 ** 111 2020-12-06 17:23 22 *** 112 2020-12-06 17:24 21 ** 113 2020-12-06 17:25 22 *** ... ..( 6 skipped). .. *** 120 2020-12-06 17:32 22 *** 121 2020-12-06 17:33 9 - 122 2020-12-06 17:34 10 - 123 2020-12-06 17:35 11 - 124 2020-12-06 17:36 11 - 125 2020-12-06 17:37 12 - 126 2020-12-06 17:38 13 - 127 2020-12-06 17:39 14 - 0 2020-12-06 17:40 10 - 1 2020-12-06 17:41 10 - 2 2020-12-06 17:42 11 - 3 2020-12-06 17:43 12 - ... ..( 2 skipped). .. - 6 2020-12-06 17:46 12 - SCT Error Recovery Control: Read: Disabled Write: Disabled ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error badly formed scsi parameters Read Device Statistics page 0x00 failed SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC