/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SK hynix SATA SSDs Device Model: HFS120G32TND-N1A2A Serial Number: -- Firmware Version: 30000P10 User Capacity: 120,034,123,776 bytes [120 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Feb 25 08:45:43 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 32) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x19) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 0 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 166 166 006 - 0 5 Retired_Block_Count -O--CK 253 100 036 - 0 9 Power_On_Hours -O--CK 074 074 000 - 23720 12 Power_Cycle_Count -O--CK 100 100 020 - 1902 100 Total_Erase_Count -O--CK 100 100 000 - 15211113 168 Min_Erase_Count -O--CK 090 085 000 - 115 169 Max_Erase_Count -O--CK 081 081 000 - 202 171 Program_Fail_Count -O--CK 253 253 000 - 0 172 Erase_Fail_Count -O--CK 253 253 000 - 0 174 Unexpect_Power_Loss_Ct ----CK 100 100 000 - 328 175 Program_Fail_Count_Chip -O--CK 253 253 000 - 0 176 Unused_Rsvd_Blk_Cnt_Tot -O--CK 253 253 000 - 0 177 Wear_Leveling_Count -O--CK 087 087 000 - 147 178 Used_Rsvd_Blk_Cnt_Chip -O--CK 100 100 000 - 19 179 Used_Rsvd_Blk_Cnt_Tot -O--CK 100 100 000 - 122 180 Erase_Fail_Count -O--CK 100 100 000 - 4406 184 End-to-End_Error -O--CK 253 253 000 - 0 187 Reported_Uncorrect -O--CK 253 253 000 - 0 188 Command_Timeout -O--CK 253 253 000 - 0 194 Temperature_Celsius -O---- 045 000 000 - 45 (Min/Max 18/65) 195 Hardware_ECC_Recovered -O--CK 253 253 000 - 0 196 Reallocated_Event_Count -O--CK 253 100 036 - 0 198 Offline_Uncorrectable -O--CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 253 253 000 - 0 204 Soft_ECC_Correction -OSR-- 100 001 000 - 30 212 Phy_Error_Count -O--CK 253 253 000 - 0 234 Unknown_SK_hynix_Attrib -O--CK 100 100 000 - 18969 241 Total_Writes_GiB -O--CK 100 100 000 - 12771 242 Total_Reads_GiB -O--CK 100 100 000 - 8434 250 Read_Retry_Count -O--CK 100 100 000 - 1906018 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 4 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 2 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL R/O 8 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 1902 --- Lifetime Power-On Resets 0x01 0x010 4 23720 --- Power-on Hours 0x01 0x018 6 24943766919 --- Logical Sectors Written 0x01 0x028 6 16473996616 --- Logical Sectors Read 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 45 --- Current Temperature 0x05 0x010 1 46 --- Average Short Term Temperature 0x05 0x018 1 46 --- Average Long Term Temperature 0x05 0x020 1 65 --- Highest Temperature 0x05 0x028 1 18 --- Lowest Temperature 0x05 0x030 1 63 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 63 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 70 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 17698927 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 13 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.16.7-desktop-1omv4003] (OpenMandriva Lx 7.2-2) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9500420AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0001BSM2 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Fri Feb 25 08:45:43 2022 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 106) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 114 099 006 - 62452609 3 Spin_Up_Time PO---- 100 096 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 686 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 073 060 030 - 22528529 9 Power_On_Hours -O--CK 096 096 000 - 3689 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 430 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 098 098 000 - 2 188 Command_Timeout -O--CK 100 097 000 - 12885098524 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 059 048 045 - 41 (Min/Max 40/41) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 1 192 Power-Off_Retract_Count -O--CK 100 100 000 - 212 193 Load_Cycle_Count -O--CK 094 094 000 - 13161 194 Temperature_Celsius -O---K 041 052 000 - 41 (0 22 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 045 042 000 - 62452609 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 451 hours (18 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d1 00 00 2e 00 00 Error: UNC at LBA = 0xd100002e = 3506438190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 d1 00 00 28 40 00 00:00:14.351 READ DMA EXT 25 00 00 00 08 00 00 d1 00 00 20 40 00 00:00:14.348 READ DMA EXT 25 00 00 00 08 00 00 d1 00 00 18 40 00 00:00:14.348 READ DMA EXT 25 00 00 00 08 00 00 d1 00 00 10 40 00 00:00:14.283 READ DMA EXT 25 00 00 00 08 00 00 d1 00 00 08 40 00 00:00:14.282 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 451 hours (18 days + 19 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 d1 00 00 2e 00 00 Error: UNC at LBA = 0xd100002e = 3506438190 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 f0 00 00 87 00 00 00 40 00 00:00:11.264 READ DMA EXT 25 00 00 00 10 00 00 86 00 00 f0 40 00 00:00:11.261 READ DMA EXT 25 00 00 00 f0 00 00 86 00 00 00 40 00 00:00:11.255 READ DMA EXT 25 00 00 00 10 00 00 85 00 00 f0 40 00 00:00:11.254 READ DMA EXT 25 00 00 00 f0 00 00 85 00 00 00 40 00 00:00:11.251 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Aborted by host 90% 1801 - # 2 Short offline Completed without error 00% 14 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 41 Celsius Power Cycle Min/Max Temperature: 40/41 Celsius Lifetime Min/Max Temperature: 22/52 Celsius Under/Over Temperature Limit Count: 0/39 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2022-02-25 06:38 42 *********************** ... ..( 23 skipped). .. *********************** 10 2022-02-25 07:02 42 *********************** 11 2022-02-25 07:03 41 ********************** ... ..( 13 skipped). .. ********************** 25 2022-02-25 07:17 41 ********************** 26 2022-02-25 07:18 42 *********************** ... ..( 6 skipped). .. *********************** 33 2022-02-25 07:25 42 *********************** 34 2022-02-25 07:26 41 ********************** ... ..( 9 skipped). .. ********************** 44 2022-02-25 07:36 41 ********************** 45 2022-02-25 07:37 40 ********************* ... ..( 9 skipped). .. ********************* 55 2022-02-25 07:47 40 ********************* 56 2022-02-25 07:48 39 ******************** ... ..( 3 skipped). .. ******************** 60 2022-02-25 07:52 39 ******************** 61 2022-02-25 07:53 40 ********************* ... ..( 11 skipped). .. ********************* 73 2022-02-25 08:05 40 ********************* 74 2022-02-25 08:06 ? - 75 2022-02-25 08:07 40 ********************* ... ..( 14 skipped). .. ********************* 90 2022-02-25 08:22 40 ********************* 91 2022-02-25 08:23 41 ********************** ... ..( 21 skipped). .. ********************** 113 2022-02-25 08:45 41 ********************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS