Probe #7118989752 of ASUSTek M4N78 SE Desktop Computer

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD10EARS-00Y5B1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Jul 23 12:07:14 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (19800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 228) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 193 056 051 - 21718 3 Spin_Up_Time POS--K 175 124 021 - 4216 4 Start_Stop_Count -O--CK 100 100 000 - 734 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 095 095 000 - 3733 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 731 192 Power-Off_Retract_Count -O--CK 200 200 000 - 649 193 Load_Cycle_Count -O--CK 159 159 000 - 125365 194 Temperature_Celsius -O---K 107 101 000 - 40 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 35005 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 35005 [12] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 96 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc96 = 16309398 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 96 e0 00 1d+06:39:55.392 READ DMA EXT 25 00 00 00 20 00 00 00 69 18 00 e0 00 1d+06:39:55.374 READ DMA EXT 25 00 00 00 08 00 00 06 75 a6 c0 e0 00 1d+06:39:55.333 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 95 e0 00 1d+06:39:52.742 READ DMA EXT 35 00 00 00 08 00 00 00 68 be 90 e0 00 1d+06:39:52.742 WRITE DMA EXT Error 35004 [11] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 95 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc95 = 16309397 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 95 e0 00 1d+06:39:52.742 READ DMA EXT 35 00 00 00 08 00 00 00 68 be 90 e0 00 1d+06:39:52.742 WRITE DMA EXT ea 00 00 00 00 27 04 3b 00 00 00 e0 00 1d+06:39:52.624 FLUSH CACHE EXT 25 00 00 00 0c 00 00 06 27 04 30 e0 00 1d+06:39:52.624 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 94 e0 00 1d+06:39:50.027 READ DMA EXT Error 35003 [10] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 94 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc94 = 16309396 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 94 e0 00 1d+06:39:50.027 READ DMA EXT 35 00 00 00 08 00 00 00 02 46 58 e0 00 1d+06:39:50.027 WRITE DMA EXT 35 00 00 00 08 00 00 00 00 09 a0 e0 00 1d+06:39:50.027 WRITE DMA EXT 25 00 00 00 08 00 00 06 27 04 28 e0 00 1d+06:39:49.982 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 93 e0 00 1d+06:39:47.352 READ DMA EXT Error 35002 [9] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 93 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc93 = 16309395 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 93 e0 00 1d+06:39:47.352 READ DMA EXT 35 00 00 00 08 00 00 00 01 10 c0 e0 00 1d+06:39:47.352 WRITE DMA EXT 25 00 00 00 14 00 00 06 73 d3 c8 e0 00 1d+06:39:47.352 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 92 e0 00 1d+06:39:44.758 READ DMA EXT 25 00 00 00 08 00 00 06 73 d3 c0 e0 00 1d+06:39:44.710 READ DMA EXT Error 35001 [8] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 92 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc92 = 16309394 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 92 e0 00 1d+06:39:44.758 READ DMA EXT 25 00 00 00 08 00 00 06 73 d3 c0 e0 00 1d+06:39:44.710 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 91 e0 00 1d+06:39:42.079 READ DMA EXT 35 00 00 00 08 00 00 00 02 0b 78 e0 00 1d+06:39:42.079 WRITE DMA EXT 25 00 00 00 04 00 00 06 0d 0b f0 e0 00 1d+06:39:42.079 READ DMA EXT Error 35000 [7] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 91 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc91 = 16309393 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 91 e0 00 1d+06:39:42.079 READ DMA EXT 35 00 00 00 08 00 00 00 02 0b 78 e0 00 1d+06:39:42.079 WRITE DMA EXT 25 00 00 00 04 00 00 06 0d 0b f0 e0 00 1d+06:39:42.079 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 90 e0 00 1d+06:39:39.484 READ DMA EXT 35 00 00 00 40 00 00 00 30 74 48 e0 00 1d+06:39:39.484 WRITE DMA EXT Error 34999 [6] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 90 e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc90 = 16309392 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 90 e0 00 1d+06:39:39.484 READ DMA EXT 35 00 00 00 40 00 00 00 30 74 48 e0 00 1d+06:39:39.484 WRITE DMA EXT 25 00 00 00 08 00 00 06 0d 0b e8 e0 00 1d+06:39:39.471 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8f e0 00 1d+06:39:36.884 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8e e0 00 1d+06:39:36.884 READ DMA EXT Error 34998 [5] occurred at disk power-on lifetime: 3639 hours (151 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 00 f8 dc 8f e0 00 Error: UNC 1 sectors at LBA = 0x00f8dc8f = 16309391 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 01 00 00 00 f8 dc 8f e0 00 1d+06:39:36.884 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8e e0 00 1d+06:39:36.884 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8d e0 00 1d+06:39:36.884 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8c e0 00 1d+06:39:36.884 READ DMA EXT 25 00 00 00 01 00 00 00 f8 dc 8b e0 00 1d+06:39:36.884 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 40 Celsius Power Cycle Min/Max Temperature: 36/40 Celsius Lifetime Min/Max Temperature: 40/46 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (129) Index Estimated Time Temperature Celsius 130 2016-07-23 04:10 36 ***************** 131 2016-07-23 04:11 36 ***************** 132 2016-07-23 04:12 37 ****************** ... ..( 6 skipped). .. ****************** 139 2016-07-23 04:19 37 ****************** 140 2016-07-23 04:20 38 ******************* ... ..( 11 skipped). .. ******************* 152 2016-07-23 04:32 38 ******************* 153 2016-07-23 04:33 39 ******************** ... ..( 21 skipped). .. ******************** 175 2016-07-23 04:55 39 ******************** 176 2016-07-23 04:56 40 ********************* ... ..( 55 skipped). .. ********************* 232 2016-07-23 05:52 40 ********************* 233 2016-07-23 05:53 ? - 234 2016-07-23 05:54 40 ********************* 235 2016-07-23 05:55 39 ******************** 236 2016-07-23 05:56 39 ******************** 237 2016-07-23 05:57 38 ******************* ... ..( 4 skipped). .. ******************* 242 2016-07-23 06:02 38 ******************* 243 2016-07-23 06:03 37 ****************** ... ..( 4 skipped). .. ****************** 248 2016-07-23 06:08 37 ****************** 249 2016-07-23 06:09 38 ******************* 250 2016-07-23 06:10 37 ****************** ... ..( 5 skipped). .. ****************** 256 2016-07-23 06:16 37 ****************** 257 2016-07-23 06:17 36 ***************** 258 2016-07-23 06:18 36 ***************** 259 2016-07-23 06:19 37 ****************** 260 2016-07-23 06:20 37 ****************** 261 2016-07-23 06:21 36 ***************** 262 2016-07-23 06:22 36 ***************** 263 2016-07-23 06:23 37 ****************** ... ..( 2 skipped). .. ****************** 266 2016-07-23 06:26 37 ****************** 267 2016-07-23 06:27 38 ******************* ... ..( 3 skipped). .. ******************* 271 2016-07-23 06:31 38 ******************* 272 2016-07-23 06:32 39 ******************** ... ..( 5 skipped). .. ******************** 278 2016-07-23 06:38 39 ******************** 279 2016-07-23 06:39 40 ********************* 280 2016-07-23 06:40 39 ******************** ... ..(128 skipped). .. ******************** 409 2016-07-23 08:49 39 ******************** 410 2016-07-23 08:50 40 ********************* 411 2016-07-23 08:51 40 ********************* 412 2016-07-23 08:52 39 ******************** ... ..( 32 skipped). .. ******************** 445 2016-07-23 09:25 39 ******************** 446 2016-07-23 09:26 38 ******************* 447 2016-07-23 09:27 39 ******************** ... ..( 4 skipped). .. ******************** 452 2016-07-23 09:32 39 ******************** 453 2016-07-23 09:33 38 ******************* ... ..( 55 skipped). .. ******************* 31 2016-07-23 10:29 38 ******************* 32 2016-07-23 10:30 39 ******************** 33 2016-07-23 10:31 ? - 34 2016-07-23 10:32 40 ********************* ... ..( 16 skipped). .. ********************* 51 2016-07-23 10:49 40 ********************* 52 2016-07-23 10:50 39 ******************** 53 2016-07-23 10:51 39 ******************** 54 2016-07-23 10:52 40 ********************* 55 2016-07-23 10:53 39 ******************** ... ..( 23 skipped). .. ******************** 79 2016-07-23 11:17 39 ******************** 80 2016-07-23 11:18 40 ********************* 81 2016-07-23 11:19 39 ******************** 82 2016-07-23 11:20 ? - 83 2016-07-23 11:21 30 *********** 84 2016-07-23 11:22 31 ************ 85 2016-07-23 11:23 32 ************* 86 2016-07-23 11:24 32 ************* 87 2016-07-23 11:25 32 ************* 88 2016-07-23 11:26 33 ************** 89 2016-07-23 11:27 33 ************** 90 2016-07-23 11:28 34 *************** 91 2016-07-23 11:29 34 *************** 92 2016-07-23 11:30 35 **************** 93 2016-07-23 11:31 35 **************** 94 2016-07-23 11:32 35 **************** 95 2016-07-23 11:33 ? - 96 2016-07-23 11:34 26 ******* ... ..( 2 skipped). .. ******* 99 2016-07-23 11:37 26 ******* 100 2016-07-23 11:38 27 ******** 101 2016-07-23 11:39 28 ********* 102 2016-07-23 11:40 29 ********** 103 2016-07-23 11:41 29 ********** 104 2016-07-23 11:42 29 ********** 105 2016-07-23 11:43 30 *********** 106 2016-07-23 11:44 30 *********** 107 2016-07-23 11:45 31 ************ 108 2016-07-23 11:46 31 ************ 109 2016-07-23 11:47 32 ************* 110 2016-07-23 11:48 32 ************* 111 2016-07-23 11:49 33 ************** ... ..( 3 skipped). .. ************** 115 2016-07-23 11:53 33 ************** 116 2016-07-23 11:54 34 *************** 117 2016-07-23 11:55 34 *************** 118 2016-07-23 11:56 34 *************** 119 2016-07-23 11:57 35 **************** 120 2016-07-23 11:58 35 **************** 121 2016-07-23 11:59 35 **************** 122 2016-07-23 12:00 36 ***************** ... ..( 6 skipped). .. ***************** 129 2016-07-23 12:07 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 13 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 2964 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3250410AS Serial Number: -- Firmware Version: 3.AAC User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Sat Jul 23 12:07:14 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 64) minutes. SCT capabilities: (0x0001) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 119 097 006 - 203128573 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1990 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 1 7 Seek_Error_Rate POSR-- 087 060 030 - 522357838 9 Power_On_Hours -O--CK 086 086 000 - 12512 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1915 187 Reported_Uncorrect -O--CK 001 001 000 - 764 189 High_Fly_Writes -O-RCK 092 092 000 - 8 190 Airflow_Temperature_Cel -O---K 057 053 045 - 43 (Min/Max 42/43) 194 Temperature_Celsius -O---K 043 047 000 - 43 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 077 053 000 - 201667909 197 Current_Pending_Sector -O--C- 100 099 000 - 1 198 Offline_Uncorrectable ----C- 100 099 000 - 1 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 771 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 771 [10] occurred at disk power-on lifetime: 12498 hours (520 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 5e 40 e0 00 Error: UNC at LBA = 0x00005e40 = 24128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d8 00 08 00 00 00 00 5e 3f e0 00 00:03:53.965 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 3f e0 00 00:03:53.962 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 47 e0 00 00:03:53.952 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 37 e0 00 00:03:53.672 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 2f e0 00 00:03:52.802 READ DMA EXT Error 770 [9] occurred at disk power-on lifetime: 12498 hours (520 days + 18 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 00 00 5e 40 e0 00 Error: UNC at LBA = 0x00005e40 = 24128 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 d8 00 08 00 00 00 00 5e 3f e0 00 00:03:53.965 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 47 e0 00 00:03:53.962 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 37 e0 00 00:03:53.952 READ DMA EXT 25 00 d8 00 08 00 00 00 00 5e 2f e0 00 00:03:53.672 READ DMA EXT 25 00 d8 00 08 00 06 98 00 1a df e0 00 00:03:52.802 READ DMA EXT Error 769 [8] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 01 00 02 1d 00 1f 5e e0 00 00:37:33.715 READ VERIFY SECTOR(S) EXT 42 00 00 00 01 00 02 1d 00 1f 5d e0 00 00:37:33.705 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:33.681 READ DMA EXT 42 00 00 00 02 00 02 1d 00 1f 5d e0 00 00:37:29.594 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:46.030 READ DMA EXT Error 768 [7] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 02 00 02 1d 00 1f 5d e0 00 00:37:33.715 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:33.705 READ DMA EXT 42 00 00 00 02 00 02 1d 00 1f 5b e0 00 00:37:33.681 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:29.594 READ DMA EXT 42 00 00 00 04 00 02 1d 00 1f 5b e0 00 00:37:29.594 READ VERIFY SECTOR(S) EXT Error 767 [6] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 04 00 02 1d 00 1f 5b e0 00 00:37:33.715 READ VERIFY SECTOR(S) EXT 42 00 00 00 04 00 02 1d 00 1f 57 e0 00 00:37:33.705 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:33.681 READ DMA EXT 42 00 00 00 08 00 02 1d 00 1f 57 e0 00 00:37:29.594 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:29.594 READ DMA EXT Error 766 [5] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 08 00 02 1d 00 1f 57 e0 00 00:37:33.715 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:33.705 READ DMA EXT 42 00 00 00 08 00 02 1d 00 1f 4f e0 00 00:37:33.681 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:29.594 READ DMA EXT 42 00 00 00 10 00 02 1d 00 1f 4f e0 00 00:37:29.594 READ VERIFY SECTOR(S) EXT Error 765 [4] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 10 00 02 1d 00 1f 4f e0 00 00:37:21.408 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:17.319 READ DMA EXT 42 00 00 00 10 00 02 1d 00 1f 3f e0 00 00:37:17.294 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:29.594 READ DMA EXT 42 00 00 00 20 00 02 1d 00 1f 5f e0 00 00:37:29.594 READ VERIFY SECTOR(S) EXT Error 764 [3] occurred at disk power-on lifetime: 12496 hours (520 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 02 1d 00 1f 5e e0 00 Error: UNC at LBA = 0x21d001f5e = 9076481886 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 00 20 00 02 1d 00 1f 3f e0 00 00:37:21.408 READ VERIFY SECTOR(S) EXT 42 00 00 00 40 00 02 1d 00 1f 7f e0 00 00:37:17.319 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:17.294 READ DMA EXT 42 00 00 00 40 00 02 1d 00 1f 3f e0 00 00:37:13.458 READ VERIFY SECTOR(S) EXT 25 00 00 00 01 00 00 00 00 00 00 e0 00 00:37:13.458 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 521 (0x0209) SCT Support Level: 1 Device State: Active (0) Current Temperature: 43 Celsius Power Cycle Max Temperature: 0 Celsius Lifetime Max Temperature: 0 Celsius SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 16 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0009 2 17 Transition from drive PhyRdy to drive PhyNRdy 0x8002 2 0 Vendor specific 0x8003 2 5 Vendor specific 0x8004 2 0 Vendor specific /dev/sdc === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD7501AALS-00J7B0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 05.00K05 User Capacity: 750 156 374 016 bytes [750 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Sat Jul 23 12:07:16 2016 YEKT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15480) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 180) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 12 3 Spin_Up_Time POS--K 253 219 021 - 5158 4 Start_Stop_Count -O--CK 073 073 000 - 27021 5 Reallocated_Sector_Ct PO--CK 115 115 140 NOW 673 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 041 041 000 - 43346 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4567 192 Power-Off_Retract_Count -O--CK 197 197 000 - 2936 193 Load_Cycle_Count -O--CK 191 191 000 - 27018 194 Temperature_Celsius -O---K 104 089 000 - 46 196 Reallocated_Event_Count -O--CK 043 043 000 - 157 197 Current_Pending_Sector -O--CK 200 200 000 - 10 198 Offline_Uncorrectable ----CK 200 200 000 - 10 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 4739 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 4 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 31882 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 31882 [9] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 08 1c 00 62 4f e0 00 Error: UNC 8 sectors at LBA = 0x81c00624f = 34829525583 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:13:03.401 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 5f e0 00 20:13:03.401 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:13:01.203 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 57 e0 00 20:13:01.190 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:59.009 READ DMA EXT Error 31881 [8] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 08 1c 00 62 4f e0 00 Error: UNC 8 sectors at LBA = 0x81c00624f = 34829525583 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:13:01.203 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 57 e0 00 20:13:01.190 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:59.009 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:56.816 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 47 e0 00 20:12:56.815 READ DMA EXT Error 31880 [7] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 08 1c 00 62 4f e0 00 Error: UNC 8 sectors at LBA = 0x81c00624f = 34829525583 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:59.009 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:56.816 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 47 e0 00 20:12:56.815 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 3f e0 00 20:12:56.814 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 37 e0 00 20:12:56.814 READ DMA EXT Error 31879 [6] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 08 1c 00 62 4f e0 00 Error: UNC 8 sectors at LBA = 0x81c00624f = 34829525583 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:56.816 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 47 e0 00 20:12:56.815 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 3f e0 00 20:12:56.814 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 37 e0 00 20:12:56.814 READ DMA EXT 25 00 00 01 00 00 08 21 00 62 37 e0 00 20:12:56.812 READ DMA EXT Error 31878 [5] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 1c 00 62 37 e0 00 Error: UNC 256 sectors at LBA = 0x81c006237 = 34829525559 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 08 1c 00 62 37 e0 00 20:12:54.573 READ DMA EXT 25 00 00 00 08 00 08 1b 00 62 f7 e0 00 20:12:54.572 READ DMA EXT 25 00 00 00 40 00 08 1b 00 62 f7 e0 00 20:12:54.571 READ DMA EXT 25 00 00 00 08 00 08 1b 00 62 77 e0 00 20:12:54.570 READ DMA EXT 25 00 00 00 80 00 08 1b 00 62 77 e0 00 20:12:54.569 READ DMA EXT Error 31877 [4] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 1c 00 62 37 e0 00 Error: UNC 256 sectors at LBA = 0x81c006237 = 34829525559 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 08 1c 00 62 37 e0 00 20:12:52.055 READ DMA EXT 25 00 00 01 00 00 08 1b 00 62 37 e0 00 20:12:52.054 READ DMA EXT 25 00 00 01 00 00 08 1a 00 62 37 e0 00 20:12:52.053 READ DMA EXT 25 00 00 01 00 00 00 f6 00 92 87 e0 00 20:12:52.051 READ DMA EXT 25 00 00 01 00 00 00 f5 00 92 87 e0 00 20:12:52.038 READ DMA EXT Error 31876 [3] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 01 00 00 08 1c 00 62 37 e0 00 Error: UNC 256 sectors at LBA = 0x81c006237 = 34829525559 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 08 1c 00 62 37 e0 00 20:12:49.848 READ DMA EXT 25 00 00 01 00 00 08 1b 00 62 37 e0 00 20:12:49.847 READ DMA EXT 25 00 00 01 00 00 08 1a 00 62 37 e0 00 20:12:49.842 READ DMA EXT 25 00 00 01 00 00 08 ca 00 5a b7 e0 00 20:12:49.841 READ DMA EXT 25 00 00 01 00 00 08 c9 00 5a b7 e0 00 20:12:49.840 READ DMA EXT Error 31875 [2] occurred at disk power-on lifetime: 43334 hours (1805 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 08 1c 00 62 4f e0 00 Error: UNC 8 sectors at LBA = 0x81c00624f = 34829525583 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:41.908 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 5f e0 00 20:12:41.907 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:39.725 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 57 e0 00 20:12:39.713 READ DMA EXT 25 00 00 00 08 00 08 1c 00 62 4f e0 00 20:12:37.548 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 9285 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 46 Celsius Power Cycle Min/Max Temperature: 46/46 Celsius Lifetime Min/Max Temperature: 46/60 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (69) Index Estimated Time Temperature Celsius 70 2016-07-23 10:00 44 ************************* 71 2016-07-23 10:01 45 ************************** ... ..( 18 skipped). .. ************************** 90 2016-07-23 10:20 45 ************************** 91 2016-07-23 10:21 46 *************************** ... ..( 22 skipped). .. *************************** 114 2016-07-23 10:44 46 *************************** 115 2016-07-23 10:45 47 **************************** ... ..( 31 skipped). .. **************************** 19 2016-07-23 11:17 47 **************************** 20 2016-07-23 11:18 46 *************************** 21 2016-07-23 11:19 46 *************************** 22 2016-07-23 11:20 46 *************************** 23 2016-07-23 11:21 ? - 24 2016-07-23 11:22 46 *************************** ... ..( 44 skipped). .. *************************** 69 2016-07-23 12:07 46 *************************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 12 Device-to-host register FISes sent due to a COMRESET 0x8000 4 2971 Vendor specific


Hardware for Linux and BSD

GitHub