Probe #6dce53c730 of MSI B85M-E45 Desktop Computer (MS-7817)

Log: smartctl

/dev/sda === START OF INFORMATION SECTION === Device Model: SPCC Solid State Disk Serial Number: -- LU WWN Device Id: 0 000000 ... Firmware Version: O0213E User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jan 27 08:52:18 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Disabled Rd look-ahead is: Disabled Write cache is: Enabled ATA Security is: Unavailable Read SCT Status failed: scsi error badly formed scsi parameters Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x71) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 1 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate ------ 100 100 050 - 0 5 Reallocated_Sector_Ct -O---- 100 100 050 - 0 9 Power_On_Hours ------ 100 100 050 - 276 12 Power_Cycle_Count ------ 100 100 050 - 645 160 Unknown_Attribute ------ 100 100 050 - 0 161 Unknown_Attribute ------ 100 100 050 - 482 162 Unknown_Attribute ------ 100 100 050 - 1 163 Unknown_Attribute ------ 100 100 050 - 130 164 Unknown_Attribute ------ 100 100 050 - 289643 165 Unknown_Attribute ------ 100 100 050 - 88 166 Unknown_Attribute ------ 100 100 050 - 37 167 Unknown_Attribute ------ 100 100 050 - 73 192 Power-Off_Retract_Count ------ 100 100 050 - 24 194 Temperature_Celsius ------ 100 100 050 - 26 195 Hardware_ECC_Recovered ------ 100 100 050 - 0 196 Reallocated_Event_Count ------ 100 100 050 - 0 199 UDMA_CRC_Error_Count ------ 100 100 050 - 1 241 Total_LBAs_Written ------ 100 100 050 - 96215 242 Total_LBAs_Read ------ 100 100 050 - 81947 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 1 Comprehensive SMART error log 0x03 GPL,SL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 SATA NCQ Queued Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 1 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1 [0] log entry is empty SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Read SCT Status failed: scsi error badly formed scsi parameters Read SCT Status failed: scsi error badly formed scsi parameters SCT (Get) Error Recovery Control command failed Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 2) == 0x01 0x008 4 645 --- Lifetime Power-On Resets 0x01 0x010 4 276 --- Power-on Hours 0x01 0x018 6 96215 --- Logical Sectors Written 0x01 0x020 6 129344485 --- Number of Write Commands 0x01 0x028 6 81947 --- Logical Sectors Read 0x01 0x030 6 107639476 --- Number of Read Commands 0x02 ===== = = === == Free-Fall Statistics (empty) == 0x03 ===== = = === == Rotating Media Statistics (empty) == 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 24 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 24 --- Current Temperature 0x05 0x010 1 -17 --- Average Short Term Temperature 0x05 0x018 1 35 --- Average Long Term Temperature 0x05 0x020 1 39 --- Highest Temperature 0x05 0x028 1 7 --- Lowest Temperature 0x05 0x030 1 -1 --- Highest Average Short Term Temperature 0x05 0x038 1 0 --- Lowest Average Short Term Temperature 0x05 0x040 1 -1 --- Highest Average Long Term Temperature 0x05 0x048 1 0 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 100 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 0 --- Specified Minimum Operating Temperature 0x06 ===== = = === == Transport Statistics (rev 1) == 0x06 0x008 4 2673 --- Number of Hardware Resets 0x06 0x018 4 0 --- Number of Interface CRC Errors 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 2 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC /dev/sdb === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue (SATA) Device Model: WDC WD2500AAKS-00VSA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01B01 User Capacity: 250 059 350 016 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) Local Time is: Fri Jan 27 08:52:18 2017 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 4800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 59) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 177 177 021 - 2108 4 Start_Stop_Count -O--CK 100 100 000 - 683 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 100 253 000 - 0 9 Power_On_Hours -O--CK 069 069 000 - 23080 10 Spin_Retry_Count -O--C- 100 100 000 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4073 192 Power-Off_Retract_Count -O--CK 200 200 000 - 190 193 Load_Cycle_Count -O--CK 199 199 000 - 4073 194 Temperature_Celsius -O---K 115 100 000 - 28 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 20/28 Celsius Lifetime Min/Max Temperature: 19/43 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/85 Celsius Temperature History Size (Index): 128 (89) Index Estimated Time Temperature Celsius 90 2017-01-27 06:45 29 ********** ... ..( 47 skipped). .. ********** 10 2017-01-27 07:33 29 ********** 11 2017-01-27 07:34 ? - 12 2017-01-27 07:35 22 *** 13 2017-01-27 07:36 22 *** 14 2017-01-27 07:37 23 **** 15 2017-01-27 07:38 24 ***** 16 2017-01-27 07:39 25 ****** 17 2017-01-27 07:40 25 ****** 18 2017-01-27 07:41 25 ****** 19 2017-01-27 07:42 26 ******* ... ..( 2 skipped). .. ******* 22 2017-01-27 07:45 26 ******* 23 2017-01-27 07:46 27 ******** 24 2017-01-27 07:47 27 ******** 25 2017-01-27 07:48 27 ******** 26 2017-01-27 07:49 28 ********* ... ..( 2 skipped). .. ********* 29 2017-01-27 07:52 28 ********* 30 2017-01-27 07:53 29 ********** ... ..( 25 skipped). .. ********** 56 2017-01-27 08:19 29 ********** 57 2017-01-27 08:20 ? - 58 2017-01-27 08:21 20 * 59 2017-01-27 08:22 20 * 60 2017-01-27 08:23 21 ** 61 2017-01-27 08:24 21 ** 62 2017-01-27 08:25 22 *** 63 2017-01-27 08:26 22 *** 64 2017-01-27 08:27 23 **** 65 2017-01-27 08:28 24 ***** 66 2017-01-27 08:29 25 ****** ... ..( 2 skipped). .. ****** 69 2017-01-27 08:32 25 ****** 70 2017-01-27 08:33 26 ******* ... ..( 5 skipped). .. ******* 76 2017-01-27 08:39 26 ******* 77 2017-01-27 08:40 27 ******** ... ..( 4 skipped). .. ******** 82 2017-01-27 08:45 27 ******** 83 2017-01-27 08:46 28 ********* ... ..( 5 skipped). .. ********* 89 2017-01-27 08:52 28 ********* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x8000 4 1949 Vendor specific


Hardware for Linux and BSD

GitHub