/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD2500BEVT-00ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 250,059,350,016 bytes [250 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Wed Jun 14 19:53:23 2023 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7500) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 90) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 15324 3 Spin_Up_Time POS--K 186 186 021 - 1658 4 Start_Stop_Count -O--CK 091 091 000 - 9342 5 Reallocated_Sector_Ct PO--CK 192 192 140 - 59 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 079 079 000 - 15769 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 092 092 000 - 8873 192 Power-Off_Retract_Count -O--CK 200 200 000 - 215 193 Load_Cycle_Count -O--CK 144 144 000 - 170135 194 Temperature_Celsius -O---K 119 085 000 - 28 196 Reallocated_Event_Count -O--CK 155 155 000 - 45 197 Current_Pending_Sector -O--CK 200 199 000 - 28 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 15029 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 15029 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c7 60 29 52 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 98 08 00 c8 29 c6 00 52 60 00 00 00 00:00:16.544 NOP [Reserved subcommand] [OBS-ACS-2] 03 c6 60 29 52 00 90 00 c8 08 00 00 04 00:45:08.166 CFA REQUEST EXTENDED ERROR 00 80 08 00 48 29 c6 00 52 61 00 00 00 00:00:06.280 NOP [Reserved subcommand] [OBS-ACS-2] Error 15028 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 cf 60 29 42 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 f0 08 00 c0 29 cb 01 42 60 00 00 00 00:00:28.920 NOP [Reserved subcommand] [OBS-ACS-2] 00 b0 60 29 42 00 c8 00 38 08 00 00 03 00:45:04.073 NOP [Reserved subcommand] [OBS-ACS-2] 00 b8 08 00 e8 29 af 03 42 60 00 00 00 00:00:14.528 NOP [Reserved subcommand] [OBS-ACS-2] Error 15027 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 ea 60 29 33 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 60 08 00 e8 29 e3 02 33 60 00 00 00 00:00:12.392 NOP [Reserved subcommand] [OBS-ACS-2] 02 de 60 29 33 00 58 00 e8 08 00 00 01 00:45:00.259 [RESERVED] 00 40 08 00 78 29 d9 01 33 60 00 00 00 00:00:38.984 NOP [Reserved subcommand] [OBS-ACS-2] Error 15026 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 8f 61 29 22 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 68 08 00 18 29 8f 04 22 60 00 00 00 00:00:59.504 NOP [Reserved subcommand] [OBS-ACS-2] 00 8f 60 29 22 00 60 00 d0 80 00 00 03 00:44:55.823 NOP [Reserved subcommand] [OBS-ACS-2] 00 50 08 00 c0 29 8e 01 22 60 00 00 00 00:00:22.616 NOP [Reserved subcommand] [OBS-ACS-2] Error 15025 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 c9 60 29 14 00 00 00 00 00 00 00 04 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 f8 08 00 88 29 6e 00 14 61 00 00 00 00:00:06.152 NOP [Reserved subcommand] [OBS-ACS-2] 01 61 60 29 14 00 f0 00 48 08 00 00 01 00:44:52.193 [RESERVED] 00 e0 08 00 08 29 50 03 14 60 00 00 00 00:00:41.192 NOP [Reserved subcommand] [OBS-ACS-2] Error 15024 [23] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 91 60 29 05 00 00 00 00 00 00 00 04 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 60 08 00 70 29 91 03 05 60 00 00 00 00:00:06.248 NOP [Reserved subcommand] [OBS-ACS-2] 03 90 60 29 05 00 58 00 48 08 00 00 01 00:44:48.400 CFA REQUEST EXTENDED ERROR 00 48 08 00 18 29 90 03 05 60 00 00 00 00:00:10.320 NOP [Reserved subcommand] [OBS-ACS-2] Error 15023 [22] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 77 60 28 f7 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 c8 08 00 28 28 77 01 f7 60 00 00 00 00:01:03.696 NOP [Reserved subcommand] [OBS-ACS-2] 00 77 60 28 f7 00 c0 00 10 08 00 00 00 00:44:44.791 NOP [Reserved subcommand] [OBS-ACS-2] 00 b0 08 00 c0 28 77 01 f7 60 00 00 00 00:01:03.672 NOP [Reserved subcommand] [OBS-ACS-2] Error 15022 [21] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 d0 60 28 e9 00 00 00 00 00 00 00 03 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 68 08 00 78 28 c8 01 e9 60 00 00 00 00:01:01.552 NOP [Reserved subcommand] [OBS-ACS-2] 01 c2 60 28 e9 00 60 00 78 08 00 00 01 00:44:41.288 [RESERVED] 00 50 08 00 f8 28 bc 00 e9 60 00 00 00 00:00:49.240 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 15492 78900340 # 2 Extended offline Completed: read failure 90% 15358 78900340 # 3 Extended offline Completed: read failure 90% 15098 78900340 # 4 Extended offline Completed: read failure 90% 14919 78900340 # 5 Extended offline Completed: read failure 90% 14802 78900340 # 6 Extended offline Completed: read failure 90% 14341 78900340 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 22/29 Celsius Lifetime Min/Max Temperature: 23/64 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (24) Index Estimated Time Temperature Celsius 25 2023-06-14 17:46 41 ********************** 26 2023-06-14 17:47 41 ********************** 27 2023-06-14 17:48 42 *********************** ... ..( 2 skipped). .. *********************** 30 2023-06-14 17:51 42 *********************** 31 2023-06-14 17:52 43 ************************ ... ..( 2 skipped). .. ************************ 34 2023-06-14 17:55 43 ************************ 35 2023-06-14 17:56 44 ************************* ... ..( 8 skipped). .. ************************* 44 2023-06-14 18:05 44 ************************* 45 2023-06-14 18:06 45 ************************** ... ..( 6 skipped). .. ************************** 52 2023-06-14 18:13 45 ************************** 53 2023-06-14 18:14 46 *************************** ... ..( 11 skipped). .. *************************** 65 2023-06-14 18:26 46 *************************** 66 2023-06-14 18:27 47 **************************** ... ..( 6 skipped). .. **************************** 73 2023-06-14 18:34 47 **************************** 74 2023-06-14 18:35 48 ***************************** ... ..( 8 skipped). .. ***************************** 83 2023-06-14 18:44 48 ***************************** 84 2023-06-14 18:45 ? - 85 2023-06-14 18:46 40 ********************* 86 2023-06-14 18:47 40 ********************* 87 2023-06-14 18:48 40 ********************* 88 2023-06-14 18:49 41 ********************** 89 2023-06-14 18:50 41 ********************** 90 2023-06-14 18:51 41 ********************** 91 2023-06-14 18:52 42 *********************** 92 2023-06-14 18:53 43 ************************ 93 2023-06-14 18:54 43 ************************ 94 2023-06-14 18:55 44 ************************* 95 2023-06-14 18:56 45 ************************** ... ..( 2 skipped). .. ************************** 98 2023-06-14 18:59 45 ************************** 99 2023-06-14 19:00 46 *************************** ... ..( 10 skipped). .. *************************** 110 2023-06-14 19:11 46 *************************** 111 2023-06-14 19:12 47 **************************** ... ..( 7 skipped). .. **************************** 119 2023-06-14 19:20 47 **************************** 120 2023-06-14 19:21 48 ***************************** ... ..( 10 skipped). .. ***************************** 3 2023-06-14 19:32 48 ***************************** 4 2023-06-14 19:33 49 ****************************** 5 2023-06-14 19:34 48 ***************************** 6 2023-06-14 19:35 49 ****************************** ... ..( 11 skipped). .. ****************************** 18 2023-06-14 19:47 49 ****************************** 19 2023-06-14 19:48 ? - 20 2023-06-14 19:49 22 *** 21 2023-06-14 19:50 23 **** 22 2023-06-14 19:51 25 ****** 23 2023-06-14 19:52 26 ******* 24 2023-06-14 19:53 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x8000 4 280 Vendor specific