/dev/sda === START OF INFORMATION SECTION === Device Model: WDC WD10EZRZ-00HTKB0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Thu Jul 21 22:32:12 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (13920) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 158) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 132 131 021 - 4358 4 Start_Stop_Count -O--CK 099 099 000 - 1276 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 098 098 000 - 1708 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 195 192 Power-Off_Retract_Count -O--CK 200 200 000 - 15 193 Load_Cycle_Count -O--CK 198 198 000 - 6898 194 Temperature_Celsius -O---K 105 096 000 - 38 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 38 Celsius Power Cycle Min/Max Temperature: 29/42 Celsius Lifetime Min/Max Temperature: 25/47 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (31) Index Estimated Time Temperature Celsius 32 2016-07-21 14:35 39 ******************** ... ..( 3 skipped). .. ******************** 36 2016-07-21 14:39 39 ******************** 37 2016-07-21 14:40 38 ******************* 38 2016-07-21 14:41 39 ******************** 39 2016-07-21 14:42 39 ******************** 40 2016-07-21 14:43 38 ******************* 41 2016-07-21 14:44 39 ******************** 42 2016-07-21 14:45 39 ******************** 43 2016-07-21 14:46 38 ******************* 44 2016-07-21 14:47 38 ******************* 45 2016-07-21 14:48 39 ******************** 46 2016-07-21 14:49 38 ******************* 47 2016-07-21 14:50 39 ******************** 48 2016-07-21 14:51 39 ******************** 49 2016-07-21 14:52 38 ******************* 50 2016-07-21 14:53 39 ******************** ... ..( 19 skipped). .. ******************** 70 2016-07-21 15:13 39 ******************** 71 2016-07-21 15:14 38 ******************* ... ..( 9 skipped). .. ******************* 81 2016-07-21 15:24 38 ******************* 82 2016-07-21 15:25 40 ********************* ... ..( 2 skipped). .. ********************* 85 2016-07-21 15:28 40 ********************* 86 2016-07-21 15:29 41 ********************** ... ..( 18 skipped). .. ********************** 105 2016-07-21 15:48 41 ********************** 106 2016-07-21 15:49 40 ********************* ... ..( 18 skipped). .. ********************* 125 2016-07-21 16:08 40 ********************* 126 2016-07-21 16:09 41 ********************** 127 2016-07-21 16:10 41 ********************** 128 2016-07-21 16:11 41 ********************** 129 2016-07-21 16:12 40 ********************* ... ..( 17 skipped). .. ********************* 147 2016-07-21 16:30 40 ********************* 148 2016-07-21 16:31 39 ******************** ... ..( 87 skipped). .. ******************** 236 2016-07-21 17:59 39 ******************** 237 2016-07-21 18:00 38 ******************* 238 2016-07-21 18:01 39 ******************** 239 2016-07-21 18:02 38 ******************* 240 2016-07-21 18:03 39 ******************** ... ..( 17 skipped). .. ******************** 258 2016-07-21 18:21 39 ******************** 259 2016-07-21 18:22 38 ******************* 260 2016-07-21 18:23 38 ******************* 261 2016-07-21 18:24 39 ******************** ... ..( 6 skipped). .. ******************** 268 2016-07-21 18:31 39 ******************** 269 2016-07-21 18:32 38 ******************* 270 2016-07-21 18:33 39 ******************** ... ..( 82 skipped). .. ******************** 353 2016-07-21 19:56 39 ******************** 354 2016-07-21 19:57 38 ******************* ... ..( 3 skipped). .. ******************* 358 2016-07-21 20:01 38 ******************* 359 2016-07-21 20:02 39 ******************** 360 2016-07-21 20:03 38 ******************* 361 2016-07-21 20:04 38 ******************* 362 2016-07-21 20:05 38 ******************* 363 2016-07-21 20:06 39 ******************** ... ..( 54 skipped). .. ******************** 418 2016-07-21 21:01 39 ******************** 419 2016-07-21 21:02 38 ******************* 420 2016-07-21 21:03 39 ******************** ... ..( 3 skipped). .. ******************** 424 2016-07-21 21:07 39 ******************** 425 2016-07-21 21:08 40 ********************* ... ..( 3 skipped). .. ********************* 429 2016-07-21 21:12 40 ********************* 430 2016-07-21 21:13 41 ********************** 431 2016-07-21 21:14 41 ********************** 432 2016-07-21 21:15 40 ********************* 433 2016-07-21 21:16 40 ********************* 434 2016-07-21 21:17 40 ********************* 435 2016-07-21 21:18 39 ******************** 436 2016-07-21 21:19 40 ********************* ... ..( 3 skipped). .. ********************* 440 2016-07-21 21:23 40 ********************* 441 2016-07-21 21:24 41 ********************** ... ..( 14 skipped). .. ********************** 456 2016-07-21 21:39 41 ********************** 457 2016-07-21 21:40 42 *********************** 458 2016-07-21 21:41 41 ********************** ... ..( 2 skipped). .. ********************** 461 2016-07-21 21:44 41 ********************** 462 2016-07-21 21:45 42 *********************** ... ..( 3 skipped). .. *********************** 466 2016-07-21 21:49 42 *********************** 467 2016-07-21 21:50 41 ********************** 468 2016-07-21 21:51 42 *********************** 469 2016-07-21 21:52 42 *********************** 470 2016-07-21 21:53 42 *********************** 471 2016-07-21 21:54 41 ********************** ... ..( 7 skipped). .. ********************** 1 2016-07-21 22:02 41 ********************** 2 2016-07-21 22:03 40 ********************* ... ..( 2 skipped). .. ********************* 5 2016-07-21 22:06 40 ********************* 6 2016-07-21 22:07 39 ******************** ... ..( 12 skipped). .. ******************** 19 2016-07-21 22:20 39 ******************** 20 2016-07-21 22:21 38 ******************* 21 2016-07-21 22:22 39 ******************** ... ..( 9 skipped). .. ******************** 31 2016-07-21 22:32 39 ******************** SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 208 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 209 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 43240 Vendor specific /dev/sdb === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 Device Model: ST3400620AS Serial Number: -- Firmware Version: 3.AAK User Capacity: 400 088 457 216 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Jul 21 22:32:12 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 33) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 132) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 090 006 - 141960858 3 Spin_Up_Time PO---- 094 092 000 - 0 4 Start_Stop_Count -O--CK 092 092 020 - 8615 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 058 045 030 - 3745869782891 9 Power_On_Hours -O--CK 078 078 000 - 19978 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 7049 187 Reported_Uncorrect -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 058 047 045 - 42 (Min/Max 28/45) 194 Temperature_Celsius -O---K 042 053 000 - 42 (0 12 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 067 056 000 - 6118632 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 10% 1210 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 252 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sdc === START OF INFORMATION SECTION === Model Family: Seagate Maxtor DiamondMax 21 Device Model: MAXTOR STM3160215AS Serial Number: -- Firmware Version: 4.AAB User Capacity: 160 041 885 696 bytes [160 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 (minor revision not indicated) Local Time is: Thu Jul 21 22:32:13 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 54) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 253 006 - 0 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4777 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 073 060 030 - 21467938 9 Power_On_Hours -O--CK 070 070 000 - 26514 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4413 187 Reported_Uncorrect -O--CK 088 088 000 - 12 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 059 047 045 - 41 (Min/Max 31/44) 194 Temperature_Celsius -O---K 041 053 000 - 41 (0 22 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 064 059 000 - 95856604 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ------ 100 253 000 - 0 202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters 0x20 GPL,SL R/O 1 Streaming performance log [OBS-8] 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x23 GPL,SL R/O 1 Delayed sector log [OBS-8] 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0 GPL,SL VS 1 Device vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL,SL VS 101 Device vendor specific log 0xa8 GPL,SL VS 20 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer 0xff GPL - 23040 Reserved SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 12 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 12 [11] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:37.214 READ DMA EXT 35 00 00 00 0d 00 04 a3 00 cf d0 e0 00 00:02:37.214 WRITE DMA EXT 25 00 00 00 40 00 02 74 00 35 aa e0 00 00:02:37.199 READ DMA EXT 35 00 00 00 08 00 00 e6 00 66 f8 e0 00 00:02:37.198 WRITE DMA EXT 35 00 00 00 08 00 00 bb 00 52 b0 e0 00 00:02:37.198 WRITE DMA EXT Error 11 [10] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:33.819 READ DMA EXT 35 00 00 01 00 00 03 73 00 74 80 e0 00 00:02:33.819 WRITE DMA EXT 25 00 00 00 40 00 02 74 00 35 6a e0 00 00:02:33.802 READ DMA EXT 35 00 00 00 08 00 02 06 00 0b 78 e0 00 00:02:30.414 WRITE DMA EXT 25 00 00 00 40 00 05 54 00 21 58 e0 00 00:02:30.414 READ DMA EXT Error 10 [9] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:27.038 READ DMA EXT 35 00 00 00 20 00 03 5c 00 f0 20 e0 00 00:02:27.034 WRITE DMA EXT 25 00 00 00 40 00 02 74 00 35 2a e0 00 00:02:27.012 READ DMA EXT 25 00 00 00 08 00 00 c5 00 6b d8 e0 00 00:02:30.414 READ DMA EXT 35 00 00 00 08 00 00 e6 00 66 f0 e0 00 00:02:30.414 WRITE DMA EXT Error 9 [8] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:27.038 READ DMA EXT 25 00 00 00 40 00 03 d4 00 11 70 e0 00 00:02:27.034 READ DMA EXT 25 00 00 00 40 00 02 73 00 35 ea e0 00 00:02:27.012 READ DMA EXT 35 00 00 00 08 00 00 e7 00 66 00 e0 00 00:02:27.012 WRITE DMA EXT 25 00 00 00 20 00 00 ad 00 43 ae e0 00 00:02:27.011 READ DMA EXT Error 8 [7] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:20.308 READ DMA EXT 25 00 00 00 38 00 05 7a 00 0e f8 e0 00 00:02:20.294 READ DMA EXT 25 00 00 01 00 00 03 73 00 74 80 e0 00 00:02:20.294 READ DMA EXT 35 00 00 00 20 00 03 32 00 23 a8 e0 00 00:02:20.294 WRITE DMA EXT 25 00 00 00 40 00 02 73 00 35 a2 e0 00 00:02:20.287 READ DMA EXT Error 7 [6] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:20.308 READ DMA EXT 25 00 00 00 40 00 05 7a 00 0e b8 e0 00 00:02:20.294 READ DMA EXT 25 00 00 00 40 00 02 73 00 35 62 e0 00 00:02:20.294 READ DMA EXT 35 00 00 00 08 00 00 f0 00 6a 98 e0 00 00:02:20.294 WRITE DMA EXT 35 00 00 00 08 00 00 e6 00 66 f8 e0 00 00:02:20.287 WRITE DMA EXT Error 6 [5] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:16.904 READ DMA EXT 25 00 00 00 40 00 05 7a 00 0e 78 e0 00 00:02:16.895 READ DMA EXT 25 00 00 00 20 00 02 7f 00 35 6e e0 00 00:02:16.882 READ DMA EXT 35 00 00 00 08 00 02 06 00 0b 78 e0 00 00:02:16.881 WRITE DMA EXT 35 00 00 00 08 00 00 f0 00 6a 78 e0 00 00:02:16.881 WRITE DMA EXT Error 5 [4] occurred at disk power-on lifetime: 22028 hours (917 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 05 5c 00 1f 1b e0 00 Error: UNC at LBA = 0x55c001f1b = 23018348315 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 05 5c 00 1f 18 e0 00 00:02:13.528 READ DMA EXT 25 00 00 00 40 00 05 7a 00 0e 38 e0 00 00:02:10.177 READ DMA EXT 25 00 00 00 03 00 02 73 00 37 87 e0 00 00:02:10.175 READ DMA EXT 35 00 00 00 08 00 00 eb 00 6a 98 e0 00 00:02:10.173 WRITE DMA EXT 35 00 00 00 08 00 00 d6 00 68 f0 e0 00 00:02:10.171 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 253 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS