/dev/sda === START OF INFORMATION SECTION === Model Family: Seagate Momentus 5400.6 Device Model: ST9320325AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0010LVM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Thu Nov 30 10:14:11 2023 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 105) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 105 087 034 - 9456358 3 Spin_Up_Time PO---- 099 099 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 10105 5 Reallocated_Sector_Ct PO--CK 092 092 036 - 177 7 Seek_Error_Rate POSR-- 064 060 030 - 1138967272251 9 Power_On_Hours -O--CK 058 058 000 - 37637 (245 236 0) 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 091 091 020 - 10094 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 2139 188 Command_Timeout -O--CK 099 095 000 - 73015563392 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 073 037 045 Past 27 (207 129 27 25 0) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 858 192 Power-Off_Retract_Count -O--CK 100 100 000 - 1583 193 Load_Cycle_Count -O--CK 001 001 000 - 564703 194 Temperature_Celsius -O---K 027 063 000 - 27 (0 14 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 054 040 000 - 9456358 196 Reallocated_Event_Count POSR-- 060 060 030 - 35847 (10425 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 10 198 Offline_Uncorrectable ----C- 100 100 000 - 10 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 2458 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2458 [17] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 09 11 00 00 Error: UNC at LBA = 0x225b0911 = 576391441 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 09 10 e0 00 00:50:25.085 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:25.049 FLUSH CACHE EXT 35 00 00 00 08 00 00 23 22 9b 20 e0 00 00:50:25.049 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:25.048 FLUSH CACHE EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:25.048 SET FEATURES [Enable SATA feature] Error 2457 [16] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 09 11 00 00 Error: UNC at LBA = 0x225b0911 = 576391441 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 09 10 e0 00 00:50:22.513 READ DMA EXT 35 00 00 00 10 00 00 23 22 9b 10 e0 00 00:50:22.511 WRITE DMA EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:22.511 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:50:22.500 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:22.499 IDENTIFY DEVICE Error 2456 [15] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 05 a0 00 00 Error: UNC at LBA = 0x225b05a0 = 576390560 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 05 a0 e0 00 00:50:19.985 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:19.983 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:50:19.972 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:19.971 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:50:19.970 SET FEATURES [Set transfer mode] Error 2455 [14] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 05 a0 00 00 Error: UNC at LBA = 0x225b05a0 = 576390560 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 05 a0 e0 00 00:50:17.468 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:17.449 FLUSH CACHE EXT 35 00 00 00 08 00 00 23 22 9b 08 e0 00 00:50:17.449 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:17.449 FLUSH CACHE EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:17.448 SET FEATURES [Enable SATA feature] Error 2454 [13] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 05 a0 00 00 Error: UNC at LBA = 0x225b05a0 = 576390560 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 05 a0 e0 00 00:50:14.934 READ DMA EXT 35 00 00 00 10 00 00 23 22 9a f8 e0 00 00:50:14.933 WRITE DMA EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:14.929 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:50:14.918 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:14.917 IDENTIFY DEVICE Error 2453 [12] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 05 a0 00 00 Error: UNC at LBA = 0x225b05a0 = 576390560 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 05 a0 e0 00 00:50:12.416 READ DMA EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:12.406 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:50:12.396 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:12.394 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 00 00:50:12.394 SET FEATURES [Set transfer mode] Error 2452 [11] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 09 11 00 00 Error: UNC at LBA = 0x225b0911 = 576391441 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 09 10 e0 00 00:50:09.889 READ DMA EXT 35 00 00 00 08 00 00 21 5a e8 00 e0 00 00:50:09.887 WRITE DMA EXT ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:50:09.886 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:50:09.876 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:09.874 IDENTIFY DEVICE Error 2451 [10] occurred at disk power-on lifetime: 37570 hours (1565 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 22 5b 09 11 00 00 Error: UNC at LBA = 0x225b0911 = 576391441 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 22 5b 09 10 e0 00 00:50:07.353 READ DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:07.341 FLUSH CACHE EXT 35 00 00 00 08 00 00 23 22 9a f0 e0 00 00:50:07.341 WRITE DMA EXT ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:50:07.321 FLUSH CACHE EXT 35 00 00 00 10 00 00 23 22 9a e0 e0 00 00:50:07.319 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed: read failure 90% 33300 570576023 # 2 Extended offline Completed: read failure 90% 29566 570576023 # 3 Extended offline Completed: read failure 10% 21063 570575142 # 4 Extended offline Completed: read failure 10% 18811 570575142 # 5 Extended offline Completed: read failure 10% 18274 570575142 # 6 Extended offline Completed: read failure 10% 17940 570575142 # 7 Extended offline Completed: read failure 10% 17493 570575142 # 8 Extended offline Completed: read failure 10% 16427 570575142 # 9 Extended offline Completed: read failure 10% 16345 570575142 #10 Extended offline Completed: read failure 90% 15480 576387791 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 25 Celsius Power Cycle Min/Max Temperature: 25/25 Celsius Lifetime Min/Max Temperature: 14/63 Celsius Under/Over Temperature Limit Count: 0/1 Vendor specific: 00 00 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 10 minutes Temperature Logging Interval: 11 minutes Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (7) Index Estimated Time Temperature Celsius 8 2023-11-29 10:49 35 **************** 9 2023-11-29 11:00 38 ******************* 10 2023-11-29 11:11 39 ******************** 11 2023-11-29 11:22 38 ******************* 12 2023-11-29 11:33 ? - 13 2023-11-29 11:44 24 ***** 14 2023-11-29 11:55 34 *************** 15 2023-11-29 12:06 37 ****************** 16 2023-11-29 12:17 38 ******************* 17 2023-11-29 12:28 37 ****************** 18 2023-11-29 12:39 37 ****************** 19 2023-11-29 12:50 36 ***************** 20 2023-11-29 13:01 37 ****************** ... ..( 2 skipped). .. ****************** 23 2023-11-29 13:34 37 ****************** 24 2023-11-29 13:45 38 ******************* 25 2023-11-29 13:56 38 ******************* 26 2023-11-29 14:07 37 ****************** 27 2023-11-29 14:18 38 ******************* ... ..( 4 skipped). .. ******************* 32 2023-11-29 15:13 38 ******************* 33 2023-11-29 15:24 41 ********************** 34 2023-11-29 15:35 44 ************************* 35 2023-11-29 15:46 45 ************************** 36 2023-11-29 15:57 41 ********************** 37 2023-11-29 16:08 41 ********************** 38 2023-11-29 16:19 ? - 39 2023-11-29 16:30 26 ******* 40 2023-11-29 16:41 37 ****************** 41 2023-11-29 16:52 ? - 42 2023-11-29 17:03 23 **** 43 2023-11-29 17:14 33 ************** 44 2023-11-29 17:25 37 ****************** 45 2023-11-29 17:36 38 ******************* 46 2023-11-29 17:47 39 ******************** 47 2023-11-29 17:58 39 ******************** 48 2023-11-29 18:09 39 ******************** 49 2023-11-29 18:20 38 ******************* 50 2023-11-29 18:31 39 ******************** 51 2023-11-29 18:42 39 ******************** 52 2023-11-29 18:53 38 ******************* 53 2023-11-29 19:04 37 ****************** 54 2023-11-29 19:15 38 ******************* 55 2023-11-29 19:26 37 ****************** 56 2023-11-29 19:37 39 ******************** 57 2023-11-29 19:48 41 ********************** 58 2023-11-29 19:59 42 *********************** 59 2023-11-29 20:10 ? - 60 2023-11-29 20:21 34 *************** 61 2023-11-29 20:32 37 ****************** ... ..( 2 skipped). .. ****************** 64 2023-11-29 21:05 37 ****************** 65 2023-11-29 21:16 38 ******************* 66 2023-11-29 21:27 37 ****************** 67 2023-11-29 21:38 38 ******************* 68 2023-11-29 21:49 38 ******************* 69 2023-11-29 22:00 39 ******************** 70 2023-11-29 22:11 38 ******************* 71 2023-11-29 22:22 38 ******************* 72 2023-11-29 22:33 37 ****************** 73 2023-11-29 22:44 39 ******************** 74 2023-11-29 22:55 ? - 75 2023-11-29 23:06 22 *** 76 2023-11-29 23:17 ? - 77 2023-11-29 23:28 23 **** 78 2023-11-29 23:39 36 ***************** 79 2023-11-29 23:50 ? - 80 2023-11-30 00:01 25 ****** 81 2023-11-30 00:12 38 ******************* 82 2023-11-30 00:23 ? - 83 2023-11-30 00:34 40 ********************* 84 2023-11-30 00:45 ? - 85 2023-11-30 00:56 41 ********************** 86 2023-11-30 01:07 ? - 87 2023-11-30 01:18 41 ********************** 88 2023-11-30 01:29 ? - 89 2023-11-30 01:40 41 ********************** 90 2023-11-30 01:51 ? - 91 2023-11-30 02:02 42 *********************** 92 2023-11-30 02:13 ? - 93 2023-11-30 02:24 40 ********************* 94 2023-11-30 02:35 ? - 95 2023-11-30 02:46 40 ********************* 96 2023-11-30 02:57 44 ************************* 97 2023-11-30 03:08 46 *************************** 98 2023-11-30 03:19 46 *************************** 99 2023-11-30 03:30 43 ************************ 100 2023-11-30 03:41 ? - 101 2023-11-30 03:52 23 **** 102 2023-11-30 04:03 37 ****************** 103 2023-11-30 04:14 45 ************************** 104 2023-11-30 04:25 46 *************************** 105 2023-11-30 04:36 ? - 106 2023-11-30 04:47 24 ***** 107 2023-11-30 04:58 35 **************** 108 2023-11-30 05:09 39 ******************** 109 2023-11-30 05:20 41 ********************** 110 2023-11-30 05:31 43 ************************ 111 2023-11-30 05:42 42 *********************** 112 2023-11-30 05:53 43 ************************ 113 2023-11-30 06:04 ? - 114 2023-11-30 06:15 23 **** 115 2023-11-30 06:26 ? - 116 2023-11-30 06:37 22 *** 117 2023-11-30 06:48 38 ******************* 118 2023-11-30 06:59 44 ************************* 119 2023-11-30 07:10 47 **************************** 120 2023-11-30 07:21 ? - 121 2023-11-30 07:32 47 **************************** 122 2023-11-30 07:43 46 *************************** 123 2023-11-30 07:54 48 ***************************** 124 2023-11-30 08:05 45 ************************** 125 2023-11-30 08:16 42 *********************** 126 2023-11-30 08:27 41 ********************** 127 2023-11-30 08:38 43 ************************ 0 2023-11-30 08:49 43 ************************ 1 2023-11-30 09:00 45 ************************** 2 2023-11-30 09:11 ? - 3 2023-11-30 09:22 25 ****** 4 2023-11-30 09:33 ? - 5 2023-11-30 09:44 24 ***** 6 2023-11-30 09:55 ? - 7 2023-11-30 10:06 25 ****** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS