/dev/nvme0n1 smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.0-kali3-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Number: Samsung SSD 980 PRO 250GB Serial Number: -- Firmware Version: 3B2QGXA7 PCI Vendor/Subsystem ID: 0x144d IEEE OUI Identifier: 0x002538 Total NVM Capacity: 250,059,350,016 [250 GB] Unallocated NVM Capacity: 0 Controller ID: 6 NVMe Version: 1.3 Number of Namespaces: 1 Namespace 1 Size/Capacity: 250,059,350,016 [250 GB] Namespace 1 Utilization: 140,999,483,392 [140 GB] Namespace 1 Formatted LBA Size: 512 Namespace 1 IEEE EUI-64: 002538 ... Local Time is: Thu Dec 8 11:25:56 2022 UTC Firmware Updates (0x16): 3 Slots, no Reset required Optional Admin Commands (0x0017): Security Format Frmw_DL Self_Test Optional NVM Commands (0x0057): Comp Wr_Unc DS_Mngmt Sav/Sel_Feat Timestmp Log Page Attributes (0x0f): S/H_per_NS Cmd_Eff_Lg Ext_Get_Lg Telmtry_Lg Maximum Data Transfer Size: 128 Pages Warning Comp. Temp. Threshold: 82 Celsius Critical Comp. Temp. Threshold: 85 Celsius Supported Power States St Op Max Active Idle RL RT WL WT Ent_Lat Ex_Lat 0 + 8.49W - - 0 0 0 0 0 0 Supported LBA Sizes (NSID 0x1) Id Fmt Data Metadt Rel_Perf 0 + 512 0 0 === START OF SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART/Health Information (NVMe Log 0x02) Critical Warning: 0x00 Temperature: 44 Celsius Available Spare: 100% Available Spare Threshold: 10% Percentage Used: 2% Data Units Read: 13,389,872 [6.85 TB] Data Units Written: 9,752,760 [4.99 TB] Host Read Commands: 255,125,271 Host Write Commands: 145,624,058 Controller Busy Time: 218 Power Cycles: 1,670 Power On Hours: 3,073 Unsafe Shutdowns: 892 Media and Data Integrity Errors: 0 Error Information Log Entries: 0 Warning Comp. Temperature Time: 0 Critical Comp. Temperature Time: 0 Temperature Sensor 1: 44 Celsius Temperature Sensor 2: 52 Celsius Error Information (NVMe Log 0x01, 16 of 64 entries) No Errors Logged /dev/sda smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.0-kali3-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Marvell based SanDisk SSDs Device Model: SanDisk Ultra II 240GB Serial Number: -- LU WWN Device Id: 5 001b44 ... Firmware Version: X41100RL User Capacity: 240,057,409,536 bytes [240 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Form Factor: 2.5 inches TRIM Command: Available, deterministic, zeroed Device is: In smartctl database 7.3/5319 ATA Version is: ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 8 11:25:56 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x11) SMART execute Offline immediate. No Auto Offline data collection support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 4 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 5 Reallocated_Sector_Ct -O--CK 100 100 --- - 0 9 Power_On_Hours -O--CK 100 100 --- - 13287 12 Power_Cycle_Count -O--CK 100 100 --- - 6504 165 Total_Write/Erase_Count -O--CK 100 100 --- - 55851811036 166 Min_W/E_Cycle -O--CK 100 100 --- - 1 167 Min_Bad_Block/Die -O--CK 100 100 --- - 26 168 Maximum_Erase_Cycle -O--CK 100 100 --- - 11 169 Total_Bad_Block -O--CK 100 100 --- - 280 170 Unknown_Marvell_Attr -O--CK 100 100 --- - 0 171 Program_Fail_Count -O--CK 100 100 --- - 0 172 Erase_Fail_Count -O--CK 100 100 --- - 0 173 Avg_Write/Erase_Count -O--CK 100 100 --- - 6 174 Unexpect_Power_Loss_Ct -O--CK 100 100 --- - 1561 184 End-to-End_Error -O--CK 100 100 --- - 0 187 Reported_Uncorrect -O--CK 100 100 --- - 0 188 Command_Timeout -O--CK 100 100 --- - 0 194 Temperature_Celsius -O---K 069 061 --- - 31 (Min/Max 14/61) 199 SATA_CRC_Error -O--CK 100 100 --- - 0 230 Perc_Write/Erase_Count -O--CK 100 100 --- - 62 85 85 232 Perc_Avail_Resrvd_Space PO--CK 100 100 004 - 100 233 Total_NAND_Writes_GiB -O--CK 100 100 --- - 1589 234 Perc_Write/Erase_Ct_BC -O--CK 100 100 --- - 2256 241 Total_Writes_GiB ----CK 253 253 --- - 1988 242 Total_Reads_GiB ----CK 253 253 --- - 2093 244 Thermal_Throttle -O--CK 000 100 --- - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xde GPL VS 8 Device vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported SCT Commands not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 6504 --- Lifetime Power-On Resets 0x01 0x018 6 3736600997877 --- Logical Sectors Written 0x01 0x020 6 26714021 --- Number of Write Commands 0x01 0x028 6 4745631722345 --- Logical Sectors Read 0x01 0x030 6 10677443 --- Number of Read Commands 0x07 ===== = = === == Solid State Device Statistics (rev 1) == 0x07 0x008 1 0 --- Percentage Used Endurance Indicator |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 4 0 Command failed due to ICRC error 0x0002 4 0 R_ERR response for data FIS 0x0005 4 0 R_ERR response for non-data FIS 0x000a 4 10 Device-to-host register FISes sent due to a COMRESET /dev/sdb smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.0-kali3-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST1000DM003-1SB102 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC43 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Dec 8 11:25:56 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 102) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 082 063 006 - 193086376 3 Spin_Up_Time PO---- 098 097 000 - 0 4 Start_Stop_Count -O--CK 091 091 020 - 10118 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 073 060 045 - 24830131 9 Power_On_Hours -O--CK 086 086 000 - 12814 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 094 094 020 - 6366 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 065 056 040 - 35 (Min/Max 21/36) 193 Load_Cycle_Count -O--CK 095 095 000 - 10196 194 Temperature_Celsius -O---K 035 011 000 - 35 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 003 001 000 - 193086376 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 11689h+01m+05.383s 241 Total_LBAs_Written ------ 100 253 000 - 7665720280 242 Total_LBAs_Read ------ 100 253 000 - 9863179684 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x04 GPL,SL R/O 8 Device Statistics log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x24 GPL R/O 512 Current Device Internal Status Data log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4120 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 4800 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 21/36 Celsius Lifetime Min/Max Temperature: 11/42 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP Log 0x04) Page Offset Size Value Flags Description 0x01 ===== = = === == General Statistics (rev 1) == 0x01 0x008 4 6366 --- Lifetime Power-On Resets 0x01 0x010 4 12814 --- Power-on Hours 0x01 0x018 6 7665840936 --- Logical Sectors Written 0x01 0x020 6 52081961 --- Number of Write Commands 0x01 0x028 6 9869370228 --- Logical Sectors Read 0x01 0x030 6 78214719 --- Number of Read Commands 0x01 0x038 6 1670214357656 --- Date and Time TimeStamp 0x03 ===== = = === == Rotating Media Statistics (rev 1) == 0x03 0x008 4 1206 --- Spindle Motor Power-on Hours 0x03 0x010 4 1206 --- Head Flying Hours 0x03 0x018 4 10196 --- Head Load Events 0x03 0x020 4 0 --- Number of Reallocated Logical Sectors 0x03 0x028 4 0 --- Read Recovery Attempts 0x03 0x030 4 0 --- Number of Mechanical Start Failures 0x03 0x038 4 0 --- Number of Realloc. Candidate Logical Sectors 0x04 ===== = = === == General Errors Statistics (rev 1) == 0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors 0x04 0x010 4 0 --- Resets Between Cmd Acceptance and Completion 0x05 ===== = = === == Temperature Statistics (rev 1) == 0x05 0x008 1 35 --- Current Temperature 0x05 0x010 1 34 --- Average Short Term Temperature 0x05 0x018 1 33 --- Average Long Term Temperature 0x05 0x020 1 44 --- Highest Temperature 0x05 0x028 1 14 --- Lowest Temperature 0x05 0x030 1 38 --- Highest Average Short Term Temperature 0x05 0x038 1 26 --- Lowest Average Short Term Temperature 0x05 0x040 1 35 --- Highest Average Long Term Temperature 0x05 0x048 1 26 --- Lowest Average Long Term Temperature 0x05 0x050 4 0 --- Time in Over-Temperature 0x05 0x058 1 55 --- Specified Maximum Operating Temperature 0x05 0x060 4 0 --- Time in Under-Temperature 0x05 0x068 1 13 --- Specified Minimum Operating Temperature |||_ C monitored condition met ||__ D supports DSN |___ N normalized value Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 10 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS /dev/sde smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.0.0-kali3-amd64] (local build) Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint M7E (AF) Device Model: SAMSUNG HM641JI Serial Number: -- LU WWN Device Id: 5 0024e9 ... Firmware Version: 2AJ10001 User Capacity: 640,135,028,736 bytes [640 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 2.5 inches Device is: In smartctl database 7.3/5319 ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Thu Dec 8 11:25:57 2022 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Write SCT (Get) Feature Control Command failed: Read of ATA output registers not implemented [JMicron] Wt Cache Reorder: Unknown (SCT Feature Control command failed) === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 8700) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 145) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 100 100 051 - 0 2 Throughput_Performance -OS--K 252 252 000 - 0 3 Spin_Up_Time PO---K 090 088 025 - 3242 4 Start_Stop_Count -O--CK 098 098 000 - 2196 5 Reallocated_Sector_Ct PO--CK 252 252 010 - 0 7 Seek_Error_Rate -OSR-K 252 252 051 - 0 8 Seek_Time_Performance --S--K 252 252 015 - 0 9 Power_On_Hours -O--CK 100 100 000 - 48456 10 Spin_Retry_Count -O--CK 252 252 051 - 0 11 Calibration_Retry_Count -O--CK 096 096 000 - 4690 12 Power_Cycle_Count -O--CK 097 097 000 - 3274 191 G-Sense_Error_Rate -O---K 100 100 000 - 126 192 Power-Off_Retract_Count -O---K 252 252 000 - 0 194 Temperature_Celsius -O---- 064 059 000 - 36 (Min/Max 15/50) 195 Hardware_ECC_Recovered -O-RCK 100 100 000 - 0 196 Reallocated_Event_Count -O--CK 252 252 000 - 0 197 Current_Pending_Sector -O--CK 252 252 000 - 0 198 Offline_Uncorrectable ----CK 252 252 000 - 0 199 UDMA_CRC_Error_Count -OS-CK 084 084 000 - 8997 200 Multi_Zone_Error_Rate -O-R-K 100 100 000 - 26 223 Load_Retry_Count -O--CK 096 096 000 - 4690 225 Load_Cycle_Count -O--CK 075 075 000 - 259034 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [JMicron] Read GP Log Directory failed SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x09 SL R/W 1 Selective self-test log 0x80-0x9f SL R/W 16 Host vendor specific log 0xe0 SL R/W 1 SCT Command/Status 0xe1 SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log (GP Log 0x03) not supported SMART Error Log Version: 1 No Errors Logged SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 758 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 34/37 Celsius Lifetime Min/Max Temperature: 17/64 Celsius Specified Max Operating Temperature: 80 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 5 minutes Temperature Logging Interval: 5 minutes Min/Max recommended Temperature: -5/80 Celsius Min/Max Temperature Limit: -10/85 Celsius Temperature History Size (Index): 128 (51) Index Estimated Time Temperature Celsius 52 2022-12-08 00:50 35 **************** ... ..( 2 skipped). .. **************** 55 2022-12-08 01:05 35 **************** 56 2022-12-08 01:10 36 ***************** ... ..( 5 skipped). .. ***************** 62 2022-12-08 01:40 36 ***************** 63 2022-12-08 01:45 35 **************** 64 2022-12-08 01:50 35 **************** 65 2022-12-08 01:55 35 **************** 66 2022-12-08 02:00 36 ***************** ... ..( 7 skipped). .. ***************** 74 2022-12-08 02:40 36 ***************** 75 2022-12-08 02:45 35 **************** ... ..( 2 skipped). .. **************** 78 2022-12-08 03:00 35 **************** 79 2022-12-08 03:05 36 ***************** ... ..( 19 skipped). .. ***************** 99 2022-12-08 04:45 36 ***************** 100 2022-12-08 04:50 37 ****************** ... ..( 8 skipped). .. ****************** 109 2022-12-08 05:35 37 ****************** 110 2022-12-08 05:40 36 ***************** ... ..( 8 skipped). .. ***************** 119 2022-12-08 06:25 36 ***************** 120 2022-12-08 06:30 35 **************** ... ..( 11 skipped). .. **************** 4 2022-12-08 07:30 35 **************** 5 2022-12-08 07:35 34 *************** 6 2022-12-08 07:40 35 **************** 7 2022-12-08 07:45 34 *************** ... ..( 14 skipped). .. *************** 22 2022-12-08 09:00 34 *************** 23 2022-12-08 09:05 35 **************** ... ..( 8 skipped). .. **************** 32 2022-12-08 09:50 35 **************** 33 2022-12-08 09:55 36 ***************** ... ..( 2 skipped). .. ***************** 36 2022-12-08 10:10 36 ***************** 37 2022-12-08 10:15 37 ****************** ... ..( 4 skipped). .. ****************** 42 2022-12-08 10:40 37 ****************** 43 2022-12-08 10:45 36 ***************** 44 2022-12-08 10:50 37 ****************** 45 2022-12-08 10:55 36 ***************** 46 2022-12-08 11:00 36 ***************** 47 2022-12-08 11:05 36 ***************** 48 2022-12-08 11:10 37 ****************** 49 2022-12-08 11:15 36 ***************** 50 2022-12-08 11:20 36 ***************** 51 2022-12-08 11:25 36 ***************** Write SCT (Get) Error Recovery Control Command failed: Read of ATA output registers not implemented [JMicron] SCT (Get) Error Recovery Control command failed Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported ATA_READ_LOG_EXT (addr=0x11:0x00, page=0, n=1) failed: 48-bit ATA commands not implemented [JMicron] Read SATA Phy Event Counters failed