/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000.B Device Model: Hitachi HDT721010SLA360 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: ST6OA31B User Capacity: 1 000 203 804 160 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Mon May 9 12:56:15 2016 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (14090) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 235) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0 2 Throughput_Performance P-S--- 100 100 054 - 0 3 Spin_Up_Time POS--- 118 118 024 - 491 (Average 482) 4 Start_Stop_Count -O--C- 099 099 000 - 4209 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 6 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 125 125 020 - 33 9 Power_On_Hours -O--C- 099 099 000 - 9074 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 3557 192 Power-Off_Retract_Count -O--CK 097 097 000 - 4234 193 Load_Cycle_Count -O--C- 097 097 000 - 4234 194 Temperature_Celsius -O---- 171 171 000 - 35 (Min/Max 14/49) 196 Reallocated_Event_Count -O--CK 100 100 000 - 6 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 11564 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x20 GPL R/O 1 Streaming performance log [OBS-8] 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 314 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 314 [1] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 46 00 00 00 00 00 00 a0 00 Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 01 46 00 00 00 00 00 00 a0 0a 00:03:19.000 SET FEATURES [Set transfer mode] ec 00 00 01 00 00 00 01 00 00 00 a0 0a 00:03:18.900 IDENTIFY DEVICE 25 00 00 01 80 00 00 42 64 32 5f e2 04 00:03:18.800 READ DMA EXT 25 00 00 02 00 00 00 42 64 31 df e0 08 00:03:18.500 READ DMA EXT 25 00 00 02 00 00 00 26 80 de ab e0 08 00:03:18.400 READ DMA EXT Error 313 [0] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 51 01 46 00 00 00 00 00 00 a0 00 Error: Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 01 46 00 00 00 00 00 00 a0 0a 00:03:19.000 SET FEATURES [Set transfer mode] ec 00 00 01 00 00 00 01 00 00 00 a0 0a 00:03:18.900 IDENTIFY DEVICE 25 00 00 01 80 00 00 42 64 32 5f e2 04 00:03:18.800 READ DMA EXT 25 00 00 02 00 00 00 42 64 31 df e0 08 00:03:18.500 READ DMA EXT 25 00 00 02 00 00 00 26 80 de ab e0 08 00:03:18.400 READ DMA EXT Error 312 [3] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 80 00 00 42 64 32 5f e2 00 Error: ICRC, ABRT 384 sectors at LBA = 0x4264325f = 1113862751 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 00 00 00 42 64 31 df e0 08 00:03:18.500 READ DMA EXT 25 00 00 02 00 00 00 26 80 de ab e0 08 00:03:18.400 READ DMA EXT 25 00 00 00 01 00 00 74 70 63 49 e0 08 00:03:17.800 READ DMA EXT 25 00 00 00 01 00 00 74 70 63 48 e0 08 00:03:17.800 READ DMA EXT 25 00 00 00 01 00 00 74 70 63 48 e0 08 00:03:17.800 READ DMA EXT Error 311 [2] occurred at disk power-on lifetime: 8911 hours (371 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 00 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ec 00 00 46 00 00 00 00 00 00 00 a0 0a 00:02:37.700 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 0a 00:02:37.700 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:02:37.700 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec ff 00 01 00 00 00 01 00 00 00 a0 0a 00:02:37.700 IDENTIFY DEVICE ec ff 00 00 00 00 00 01 00 00 00 a0 04 00:02:37.500 IDENTIFY DEVICE SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 8835 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 35 Celsius Power Cycle Min/Max Temperature: 33/35 Celsius Lifetime Min/Max Temperature: 14/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -40/70 Celsius Temperature History Size (Index): 128 (60) Index Estimated Time Temperature Celsius 61 2016-05-09 10:49 40 ********************* ... ..( 37 skipped). .. ********************* 99 2016-05-09 11:27 40 ********************* 100 2016-05-09 11:28 41 ********************** 101 2016-05-09 11:29 41 ********************** 102 2016-05-09 11:30 40 ********************* ... ..( 2 skipped). .. ********************* 105 2016-05-09 11:33 40 ********************* 106 2016-05-09 11:34 41 ********************** 107 2016-05-09 11:35 41 ********************** 108 2016-05-09 11:36 40 ********************* 109 2016-05-09 11:37 41 ********************** ... ..( 3 skipped). .. ********************** 113 2016-05-09 11:41 41 ********************** 114 2016-05-09 11:42 40 ********************* 115 2016-05-09 11:43 40 ********************* 116 2016-05-09 11:44 41 ********************** 117 2016-05-09 11:45 40 ********************* 118 2016-05-09 11:46 41 ********************** ... ..( 3 skipped). .. ********************** 122 2016-05-09 11:50 41 ********************** 123 2016-05-09 11:51 40 ********************* 124 2016-05-09 11:52 41 ********************** ... ..( 3 skipped). .. ********************** 0 2016-05-09 11:56 41 ********************** 1 2016-05-09 11:57 40 ********************* ... ..( 52 skipped). .. ********************* 54 2016-05-09 12:50 40 ********************* 55 2016-05-09 12:51 ? - 56 2016-05-09 12:52 33 ************** 57 2016-05-09 12:53 34 *************** 58 2016-05-09 12:54 34 *************** 59 2016-05-09 12:55 34 *************** 60 2016-05-09 12:56 35 **************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS