/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-22ZCT0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 11.01A11 User Capacity: 320 072 933 376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Tue Aug 25 23:09:55 2015 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 127) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 2418 3 Spin_Up_Time POS--K 184 183 021 - 1800 4 Start_Stop_Count -O--CK 097 097 000 - 3183 5 Reallocated_Sector_Ct PO--CK 192 192 140 - 61 7 Seek_Error_Rate -OSR-K 100 253 000 - 0 9 Power_On_Hours -O--CK 083 083 000 - 13115 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 098 098 000 - 2979 192 Power-Off_Retract_Count -O--CK 200 200 000 - 535 193 Load_Cycle_Count -O--CK 104 104 000 - 289874 194 Temperature_Celsius -O---K 097 073 000 - 50 196 Reallocated_Event_Count -O--CK 193 193 000 - 7 197 Current_Pending_Sector -O--CK 200 200 000 - 8 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate P--R-- 100 253 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 1664 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1664 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 04 61 e4 db 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 08 00 30 e4 04 00 db 61 00 00 00 00:00:24.616 NOP [Reserved subcommand] [OBS-ACS-2] 00 03 61 e4 db 00 18 00 30 08 00 00 00 04:09:58.276 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 01 00 f0 e4 02 00 db 61 00 00 00 00:00:26.640 NOP [Don't abort queued commands] [OBS-ACS-2] Error 1663 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 1b 61 e4 cd 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 38 08 00 30 e4 1a 00 cd 61 00 00 00 00:00:24.640 NOP [Reserved subcommand] [OBS-ACS-2] 0e 1a 61 e4 cd 00 30 00 80 08 00 00 00 04:09:54.714 [RESERVED] 00 28 08 00 0f e4 19 09 cd 61 00 00 00 00:00:26.664 NOP [Reserved subcommand] [OBS-ACS-2] Error 1662 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f7 60 e4 bf 00 00 00 00 00 00 00 0b 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 c0 00 00 e4 f7 04 bf 60 00 00 00 00:00:30.736 NOP [Reserved subcommand] [OBS-ACS-2] 00 33 60 e4 b2 00 00 00 00 02 00 00 0b 04:09:51.351 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 c0 00 00 e4 1d 04 b2 60 00 00 00 00:00:30.728 NOP [Reserved subcommand] [OBS-ACS-2] Error 1661 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 33 60 e4 b2 00 00 00 00 00 00 00 0b 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 c0 00 00 e4 1d 04 b2 60 00 00 00 00:00:30.728 NOP [Reserved subcommand] [OBS-ACS-2] 0b 1c ef e4 b2 00 08 00 80 08 00 00 00 04:09:47.805 REQUEST SENSE DATA EXT 00 18 08 00 80 e4 e6 0b a4 60 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] Error 1660 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e6 60 e4 a4 00 00 00 00 00 00 00 0b 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 c0 00 00 e4 e6 04 a4 60 00 00 00 00:00:32.792 NOP [Reserved subcommand] [OBS-ACS-2] 00 90 61 e4 97 00 00 00 00 02 00 00 00 04:09:44.422 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 08 00 60 e4 90 00 97 61 00 00 00 00:00:22.552 NOP [Reserved subcommand] [OBS-ACS-2] Error 1659 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 90 61 e4 97 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 08 08 00 60 e4 90 00 97 61 00 00 00 00:00:22.552 NOP [Reserved subcommand] [OBS-ACS-2] 04 8f 60 e4 97 00 40 00 00 c0 00 00 0b 04:09:41.007 [RESERVED] 00 08 28 00 60 e4 8f 00 97 61 00 00 00 00:00:32.784 NOP [Reserved subcommand] [OBS-ACS-2] Error 1658 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 97 61 e4 89 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 08 00 30 e4 97 00 89 61 00 00 00 00:00:26.664 NOP [Reserved subcommand] [OBS-ACS-2] 00 96 61 e4 89 00 20 00 30 08 00 00 00 04:09:37.431 NOP [Reserved subcommand] [OBS-ACS-2] 00 10 08 00 60 e4 96 00 89 61 00 00 00 00:00:49.176 NOP [Reserved subcommand] [OBS-ACS-2] Error 1657 [0] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 00 00 51 00 00 40 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f0 61 e4 7b 00 00 00 00 00 00 00 00 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 00 38 08 00 30 e4 ef 00 7b 61 00 00 00 00:00:26.688 NOP [Reserved subcommand] [OBS-ACS-2] 00 ee 61 e4 7b 00 30 00 30 08 00 00 00 04:09:33.935 NOP [Reserved subcommand] [OBS-ACS-2] 00 20 08 00 50 e4 ee 00 7b 61 00 00 00 00:00:24.616 NOP [Reserved subcommand] [OBS-ACS-2] SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: SMART Off-line Data Collection executing in background (4) Current Temperature: 50 Celsius Power Cycle Min/Max Temperature: 24/52 Celsius Lifetime Min/Max Temperature: 25/75 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 5/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (65) Index Estimated Time Temperature Celsius 66 2015-08-25 21:02 34 *************** 67 2015-08-25 21:03 34 *************** 68 2015-08-25 21:04 35 **************** 69 2015-08-25 21:05 36 ***************** 70 2015-08-25 21:06 37 ****************** 71 2015-08-25 21:07 37 ****************** 72 2015-08-25 21:08 38 ******************* 73 2015-08-25 21:09 39 ******************** 74 2015-08-25 21:10 39 ******************** 75 2015-08-25 21:11 39 ******************** 76 2015-08-25 21:12 40 ********************* 77 2015-08-25 21:13 41 ********************** 78 2015-08-25 21:14 41 ********************** 79 2015-08-25 21:15 41 ********************** 80 2015-08-25 21:16 42 *********************** 81 2015-08-25 21:17 42 *********************** 82 2015-08-25 21:18 43 ************************ 83 2015-08-25 21:19 43 ************************ 84 2015-08-25 21:20 44 ************************* ... ..( 2 skipped). .. ************************* 87 2015-08-25 21:23 44 ************************* 88 2015-08-25 21:24 45 ************************** ... ..( 2 skipped). .. ************************** 91 2015-08-25 21:27 45 ************************** 92 2015-08-25 21:28 46 *************************** 93 2015-08-25 21:29 46 *************************** 94 2015-08-25 21:30 46 *************************** 95 2015-08-25 21:31 47 **************************** ... ..( 4 skipped). .. **************************** 100 2015-08-25 21:36 47 **************************** 101 2015-08-25 21:37 48 ***************************** 102 2015-08-25 21:38 48 ***************************** 103 2015-08-25 21:39 48 ***************************** 104 2015-08-25 21:40 49 ****************************** ... ..( 5 skipped). .. ****************************** 110 2015-08-25 21:46 49 ****************************** 111 2015-08-25 21:47 50 ******************************* ... ..( 5 skipped). .. ******************************* 117 2015-08-25 21:53 50 ******************************* 118 2015-08-25 21:54 51 ******************************** ... ..( 14 skipped). .. ******************************** 5 2015-08-25 22:09 51 ******************************** 6 2015-08-25 22:10 52 ********************************* 7 2015-08-25 22:11 51 ******************************** 8 2015-08-25 22:12 52 ********************************* ... ..( 19 skipped). .. ********************************* 28 2015-08-25 22:32 52 ********************************* 29 2015-08-25 22:33 51 ******************************** ... ..( 19 skipped). .. ******************************** 49 2015-08-25 22:53 51 ******************************** 50 2015-08-25 22:54 50 ******************************* ... ..( 3 skipped). .. ******************************* 54 2015-08-25 22:58 50 ******************************* 55 2015-08-25 22:59 51 ******************************** ... ..( 4 skipped). .. ******************************** 60 2015-08-25 23:04 51 ******************************** 61 2015-08-25 23:05 50 ******************************* ... ..( 3 skipped). .. ******************************* 65 2015-08-25 23:09 50 ******************************* SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 3 Device-to-host register FISes sent due to a COMRESET 0x8000 4 8253 Vendor specific