Probe #376d1a0575 of HP G72

Log: smartctl

/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.12.1-desktop-1omv2490] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9320423AS Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: 0006HPM1 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Form Factor: 2.5 inches Device is: In smartctl database ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Wed Jan 1 17:38:36 2025 GMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Unknown === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 78) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 113 098 006 - 51295346 3 Spin_Up_Time -O---- 097 097 000 - 0 4 Start_Stop_Count PO--CK 092 092 000 - 9041 5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0 7 Seek_Error_Rate POSR-- 082 060 030 - 13383862470 9 Power_On_Hours -O--CK 096 096 000 - 4230 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count PO--CK 094 037 020 - 7123 183 Runtime_Bad_Block -O--CK 100 253 000 - 0 184 End-to-End_Error PO--CK 100 100 097 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 112 188 Command_Timeout -O--CK 100 099 000 - 5 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 073 047 045 - 27 (Min/Max 23/27) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 4 192 Power-Off_Retract_Count -O--CK 100 100 000 - 106 193 Load_Cycle_Count -O--CK 079 079 000 - 43820 194 Temperature_Celsius -O---K 027 053 000 - 27 (0 11 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 053 040 000 - 51295346 196 Reallocated_Event_Count PO--CK 100 100 036 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 1 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 254 Free_Fall_Sensor -O--CK 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 GPL,SL R/O 1 Summary SMART error log 0x02 GPL,SL R/O 5 Comprehensive SMART error log 0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log 0x06 GPL,SL R/O 1 SMART self-test log 0x07 GPL,SL R/O 1 Extended self-test log 0x09 GPL,SL R/W 1 Selective self-test log 0x10 GPL,SL R/O 1 NCQ Command Error log 0x11 GPL,SL R/O 1 SATA Phy Event Counters log 0x21 GPL,SL R/O 1 Write stream error log 0x22 GPL,SL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 2248 Device vendor specific log 0xa8 GPL,SL VS 65 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xb0 GPL VS 2864 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 92 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 92 [11] occurred at disk power-on lifetime: 4039 hours (168 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: UNC at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 16 6e 00 15 b0 40 00 00:29:36.745 READ FPDMA QUEUED 60 00 00 00 40 00 14 38 00 62 f8 40 00 00:29:36.743 READ FPDMA QUEUED 61 00 00 00 60 00 0f 68 00 84 40 40 00 00:29:36.742 WRITE FPDMA QUEUED 61 00 00 00 20 00 0e 17 00 66 40 40 00 00:29:36.741 WRITE FPDMA QUEUED 60 00 00 00 40 00 0c a0 00 90 7a 40 00 00:29:36.740 READ FPDMA QUEUED Error 91 [10] occurred at disk power-on lifetime: 4039 hours (168 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: UNC at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 10 00 16 29 00 69 c0 40 00 00:29:33.659 READ FPDMA QUEUED 60 00 00 00 80 00 16 3b 00 65 e8 40 00 00:29:33.658 READ FPDMA QUEUED 60 00 00 00 10 00 16 5e 00 1a 10 40 00 00:29:33.658 READ FPDMA QUEUED 60 00 00 00 08 00 12 d1 00 f3 f0 40 00 00:29:33.658 READ FPDMA QUEUED 60 00 00 00 08 00 12 6a 00 ee 18 40 00 00:29:33.655 READ FPDMA QUEUED Error 90 [9] occurred at disk power-on lifetime: 4039 hours (168 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: WP at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 18 00 0c f3 00 0c 70 40 00 00:29:30.658 WRITE FPDMA QUEUED 61 00 00 00 08 00 00 dc 00 a9 18 40 00 00:29:30.657 WRITE FPDMA QUEUED 60 00 00 00 40 00 0f 13 00 d3 e0 40 00 00:29:30.655 READ FPDMA QUEUED 60 00 00 01 00 00 0f 12 00 d3 e0 40 00 00:29:30.654 READ FPDMA QUEUED 60 00 00 01 00 00 0f 11 00 d3 e0 40 00 00:29:30.653 READ FPDMA QUEUED Error 89 [8] occurred at disk power-on lifetime: 4039 hours (168 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: WP at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 44 00 01 63 00 c2 e0 40 00 00:29:27.260 WRITE FPDMA QUEUED 61 00 00 01 00 00 01 62 00 c2 e0 40 00 00:29:27.260 WRITE FPDMA QUEUED 61 00 00 01 00 00 01 61 00 c2 e0 40 00 00:29:27.259 WRITE FPDMA QUEUED 61 00 00 01 00 00 01 60 00 c2 e0 40 00 00:29:27.258 WRITE FPDMA QUEUED 61 00 00 01 00 00 01 5f 00 c2 e0 40 00 00:29:27.258 WRITE FPDMA QUEUED Error 88 [7] occurred at disk power-on lifetime: 4039 hours (168 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: UNC at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 08 00 1b fd 00 00 58 40 00 00:29:23.962 READ FPDMA QUEUED 60 00 00 00 08 00 00 33 00 5b f0 40 00 00:29:23.951 READ FPDMA QUEUED 60 00 00 00 08 00 00 04 00 1c 10 40 00 00:29:23.942 READ FPDMA QUEUED 61 00 00 00 a0 00 0f 62 00 84 e0 40 00 00:29:23.902 WRITE FPDMA QUEUED 60 00 00 00 40 00 1b 18 00 83 6a 40 00 00:29:23.892 READ FPDMA QUEUED Error 87 [6] occurred at disk power-on lifetime: 4022 hours (167 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: WP at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 00 00 08 00 0c f3 00 0c f0 40 00 00:08:36.277 WRITE FPDMA QUEUED 61 00 00 00 a0 00 0c 17 00 0d 60 40 00 00:08:36.276 WRITE FPDMA QUEUED 60 00 00 00 40 00 00 1f 00 12 92 40 00 00:08:36.275 READ FPDMA QUEUED 60 00 00 00 80 00 1b 63 00 c7 88 40 00 00:08:36.260 READ FPDMA QUEUED 60 00 00 00 80 00 1b 63 00 bf 88 40 00 00:08:36.251 READ FPDMA QUEUED Error 86 [5] occurred at disk power-on lifetime: 4022 hours (167 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: UNC at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 20 23 00 0e 98 40 00 00:08:33.315 READ FPDMA QUEUED 60 00 00 00 20 00 01 54 00 83 20 40 00 00:08:33.315 READ FPDMA QUEUED 60 00 00 00 08 00 00 5a 00 09 f0 40 00 00:08:33.314 READ FPDMA QUEUED 60 00 00 00 38 00 07 93 00 06 4a 40 00 00:08:33.314 READ FPDMA QUEUED 60 00 00 00 1d 00 22 f2 00 37 50 40 00 00:08:33.313 READ FPDMA QUEUED Error 85 [4] occurred at disk power-on lifetime: 4022 hours (167 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 01 54 00 83 2b 00 00 Error: UNC at LBA = 0x15400832b = 5704287019 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 40 00 0c d1 00 72 3a 40 00 00:08:30.690 READ FPDMA QUEUED 60 00 00 00 40 00 0c 76 00 71 e2 40 00 00:08:30.682 READ FPDMA QUEUED 60 00 00 00 40 00 0c f5 00 70 0a 40 00 00:08:30.674 READ FPDMA QUEUED 60 00 00 00 38 00 07 93 00 06 4a 40 00 00:08:30.639 READ FPDMA QUEUED 60 00 00 00 80 00 20 23 00 0e 98 40 00 00:08:30.629 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 40% 2522 25383979 # 2 Short offline Completed without error 00% 1840 - # 3 Short offline Completed without error 00% 1836 - # 4 Short offline Completed without error 00% 1829 - # 5 Short offline Completed without error 00% 1825 - # 6 Short offline Completed without error 00% 1818 - # 7 Short offline Completed without error 00% 1812 - # 8 Short offline Completed without error 00% 1803 - # 9 Short offline Interrupted (host reset) 00% 1795 - #10 Short offline Completed without error 00% 1788 - #11 Short offline Completed without error 00% 1781 - #12 Short offline Interrupted (host reset) 00% 1775 - #13 Short offline Interrupted (host reset) 00% 1772 - #14 Short offline Completed without error 00% 1769 - #15 Short offline Interrupted (host reset) 00% 1761 - #16 Short offline Completed without error 00% 1752 - #17 Short offline Completed without error 00% 1747 - #18 Short offline Completed without error 00% 1744 - #19 Short offline Completed without error 00% 1742 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 23/27 Celsius Lifetime Min/Max Temperature: 11/53 Celsius Under/Over Temperature Limit Count: 0/3 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/ 0 Celsius Min/Max Temperature Limit: 0/ 0 Celsius Temperature History Size (Index): 128 (67) Index Estimated Time Temperature Celsius 68 2025-01-01 15:31 ? - 69 2025-01-01 15:32 31 ************ 70 2025-01-01 15:33 32 ************* 71 2025-01-01 15:34 33 ************** 72 2025-01-01 15:35 34 *************** 73 2025-01-01 15:36 35 **************** 74 2025-01-01 15:37 36 ***************** 75 2025-01-01 15:38 37 ****************** 76 2025-01-01 15:39 37 ****************** 77 2025-01-01 15:40 38 ******************* 78 2025-01-01 15:41 39 ******************** 79 2025-01-01 15:42 39 ******************** 80 2025-01-01 15:43 40 ********************* 81 2025-01-01 15:44 40 ********************* 82 2025-01-01 15:45 41 ********************** 83 2025-01-01 15:46 41 ********************** 84 2025-01-01 15:47 42 *********************** 85 2025-01-01 15:48 42 *********************** 86 2025-01-01 15:49 42 *********************** 87 2025-01-01 15:50 43 ************************ 88 2025-01-01 15:51 43 ************************ 89 2025-01-01 15:52 43 ************************ 90 2025-01-01 15:53 44 ************************* ... ..( 2 skipped). .. ************************* 93 2025-01-01 15:56 44 ************************* 94 2025-01-01 15:57 45 ************************** ... ..( 3 skipped). .. ************************** 98 2025-01-01 16:01 45 ************************** 99 2025-01-01 16:02 46 *************************** ... ..( 5 skipped). .. *************************** 105 2025-01-01 16:08 46 *************************** 106 2025-01-01 16:09 45 ************************** ... ..( 5 skipped). .. ************************** 112 2025-01-01 16:15 45 ************************** 113 2025-01-01 16:16 46 *************************** ... ..( 12 skipped). .. *************************** 126 2025-01-01 16:29 46 *************************** 127 2025-01-01 16:30 47 **************************** ... ..( 11 skipped). .. **************************** 11 2025-01-01 16:42 47 **************************** 12 2025-01-01 16:43 48 ***************************** ... ..( 4 skipped). .. ***************************** 17 2025-01-01 16:48 48 ***************************** 18 2025-01-01 16:49 ? - 19 2025-01-01 16:50 44 ************************* 20 2025-01-01 16:51 44 ************************* 21 2025-01-01 16:52 45 ************************** ... ..( 2 skipped). .. ************************** 24 2025-01-01 16:55 45 ************************** 25 2025-01-01 16:56 46 *************************** 26 2025-01-01 16:57 46 *************************** 27 2025-01-01 16:58 ? - 28 2025-01-01 16:59 17 - 29 2025-01-01 17:00 18 - 30 2025-01-01 17:01 20 * 31 2025-01-01 17:02 21 ** 32 2025-01-01 17:03 23 **** 33 2025-01-01 17:04 24 ***** 34 2025-01-01 17:05 25 ****** 35 2025-01-01 17:06 26 ******* 36 2025-01-01 17:07 27 ******** 37 2025-01-01 17:08 27 ******** 38 2025-01-01 17:09 28 ********* 39 2025-01-01 17:10 29 ********** 40 2025-01-01 17:11 30 *********** 41 2025-01-01 17:12 30 *********** 42 2025-01-01 17:13 31 ************ 43 2025-01-01 17:14 31 ************ 44 2025-01-01 17:15 32 ************* 45 2025-01-01 17:16 33 ************** 46 2025-01-01 17:17 33 ************** 47 2025-01-01 17:18 34 *************** 48 2025-01-01 17:19 34 *************** 49 2025-01-01 17:20 35 **************** 50 2025-01-01 17:21 35 **************** 51 2025-01-01 17:22 36 ***************** 52 2025-01-01 17:23 36 ***************** 53 2025-01-01 17:24 36 ***************** 54 2025-01-01 17:25 37 ****************** ... ..( 2 skipped). .. ****************** 57 2025-01-01 17:28 37 ****************** 58 2025-01-01 17:29 38 ******************* ... ..( 2 skipped). .. ******************* 61 2025-01-01 17:32 38 ******************* 62 2025-01-01 17:33 37 ****************** 63 2025-01-01 17:34 36 ***************** 64 2025-01-01 17:35 ? - 65 2025-01-01 17:36 23 **** 66 2025-01-01 17:37 24 ***** 67 2025-01-01 17:38 27 ******** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS


Hardware for Linux and BSD

GitHub