/dev/sda === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint P120 Device Model: SAMSUNG SP2504C Serial Number: -- Firmware Version: VT100-52 User Capacity: 250 000 000 000 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 4a Local Time is: Wed Mar 9 23:29:34 2016 MSK ==> WARNING: May need -F samsung3 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 254 (maximum performance), recommended: 254 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 5106) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 85) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 100 098 051 - 0 3 Spin_Up_Time POS--- 253 253 025 - 5632 4 Start_Stop_Count -O--CK 093 093 000 - 7668 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 3 7 Seek_Error_Rate -OSR-- 253 253 000 - 0 8 Seek_Time_Performance --S--K 253 253 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 12358 10 Spin_Retry_Count -O--CK 253 253 000 - 0 11 Calibration_Retry_Count -O--C- 253 253 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4180 187 Reported_Uncorrect -O--CK 098 098 000 - 1703939 190 Airflow_Temperature_Cel -O---K 121 088 000 - 39 194 Temperature_Celsius -O---K 121 088 000 - 39 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 2158358 196 Reallocated_Event_Count -O--CK 100 100 000 - 3 197 Current_Pending_Sector -O--C- 253 100 000 - 0 198 Offline_Uncorrectable ----CK 253 253 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 198 196 000 - 20836 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 253 100 000 - 0 202 Data_Address_Mark_Errs -O--CK 097 097 000 - 1167 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 2 Comprehensive SMART error log 0x03 GPL R/O 2 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Invalid Error Log index = 0x0000, trying reserved byte (0x08) instead Device Error Count: 60648 (device log contains only the most recent 8 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 60648 [7] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 00 d5 df 8f e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x00d5df8f = 14016399 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 d5 df 8f e0 00 00:25:00.563 READ DMA EXT 25 00 00 00 40 00 00 00 d5 df 4f e0 00 00:25:00.563 READ DMA EXT 25 00 00 00 40 00 00 00 d5 df 0f e0 00 00:25:00.563 READ DMA EXT 25 00 00 00 40 00 00 00 d5 de cf e0 00 00:25:00.563 READ DMA EXT 25 00 00 00 40 00 00 00 d5 de 8f e0 00 00:25:00.563 READ DMA EXT Error 60647 [6] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 00 d5 b4 37 e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x00d5b437 = 14005303 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 d5 b4 37 e0 00 00:25:00.438 READ DMA EXT 25 00 00 00 40 00 00 00 d5 b3 f7 e0 00 00:25:00.438 READ DMA EXT 25 00 00 00 40 00 00 00 d5 b3 b7 e0 00 00:25:00.438 READ DMA EXT 25 00 00 00 40 00 00 00 d5 b3 77 e0 00 00:25:00.438 READ DMA EXT 25 00 00 00 40 00 00 00 d5 b3 37 e0 00 00:25:00.438 READ DMA EXT Error 60646 [5] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 00 d5 99 4f e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x00d5994f = 13998415 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 d5 99 4f e0 00 00:25:00.375 READ DMA EXT 25 00 00 00 40 00 00 00 d5 99 0f e0 00 00:25:00.375 READ DMA EXT 25 00 00 00 08 00 00 00 d5 99 07 e0 00 00:25:00.375 READ DMA EXT 25 00 00 00 40 00 00 00 d5 98 c7 e0 00 00:25:00.375 READ DMA EXT 25 00 00 00 40 00 00 00 d5 98 87 e0 00 00:25:00.375 READ DMA EXT Error 60645 [4] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 01 00 00 00 0f 83 d2 5f e0 00 Error: ICRC, ABRT 256 sectors at LBA = 0x0f83d25f = 260297311 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 0f 83 d2 5f e0 00 00:24:59.938 READ DMA EXT 25 00 00 00 80 00 00 0f 83 d1 df e0 00 00:24:59.875 READ DMA EXT 25 00 00 01 00 00 00 0f 83 d0 df e0 00 00:24:59.875 READ DMA EXT 25 00 00 01 00 00 00 0f 83 cf df e0 00 00:24:59.875 READ DMA EXT 25 00 00 01 00 00 00 0f 83 ce df e0 00 00:24:59.875 READ DMA EXT Error 60644 [3] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 03 18 30 3f e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x0318303f = 51916863 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 03 18 30 3f e0 00 00:24:59.313 READ DMA EXT 25 00 00 00 40 00 00 03 18 2f ff e0 00 00:24:59.313 READ DMA EXT 25 00 00 00 40 00 00 03 18 2f bf e0 00 00:24:59.313 READ DMA EXT 25 00 00 00 40 00 00 03 18 2f 7f e0 00 00:24:59.313 READ DMA EXT 25 00 00 00 40 00 00 03 18 2f 3f e0 00 00:24:59.313 READ DMA EXT Error 60643 [2] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 40 00 00 00 dc bb 97 e0 00 Error: ICRC, ABRT 64 sectors at LBA = 0x00dcbb97 = 14465943 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 40 00 00 00 dc bb 97 e0 00 00:24:59.063 READ DMA EXT 25 00 00 00 40 00 00 00 dc bb 57 e0 00 00:24:59.063 READ DMA EXT 25 00 00 00 40 00 00 00 dc bb 0f e0 00 00:24:59.063 READ DMA EXT 25 00 00 00 40 00 00 00 dc ba cf e0 00 00:24:59.063 READ DMA EXT 25 00 00 00 40 00 00 00 dc ba 87 e0 00 00:24:59.063 READ DMA EXT Error 60642 [1] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 80 00 00 09 d1 5c 4f e0 00 Error: ICRC, ABRT 128 sectors at LBA = 0x09d15c4f = 164715599 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 80 00 00 09 d1 5c 4f e0 00 00:24:57.250 READ DMA EXT 25 00 00 00 80 00 00 09 d3 da ff e0 00 00:24:57.250 READ DMA EXT 25 00 00 00 80 00 00 09 d3 de a7 e0 00 00:24:57.250 READ DMA EXT 25 00 00 00 80 00 00 09 d3 0b 27 e0 00 00:24:57.250 READ DMA EXT 25 00 00 00 80 00 00 09 d4 cd 97 e0 00 00:24:57.250 READ DMA EXT Error 60641 [0] occurred at disk power-on lifetime: 12062 hours (502 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 84 -- 51 00 70 00 00 09 d3 f9 1f e0 00 Error: ICRC, ABRT 112 sectors at LBA = 0x09d3f91f = 164886815 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 70 00 00 09 d3 f9 1f e0 00 00:24:25.438 READ DMA EXT 25 00 00 00 80 00 00 09 d3 fa 2f e0 00 00:24:25.438 READ DMA EXT 25 00 00 00 58 00 00 09 d3 f8 f7 e0 00 00:24:25.438 READ DMA EXT 25 00 00 00 80 00 00 09 d3 d9 cf e0 00 00:24:25.438 READ DMA EXT 25 00 00 00 78 00 00 09 d3 f9 17 e0 00 00:24:25.438 READ DMA EXT SMART Extended Self-test Log (GP Log 0x07) not supported SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Max Temperature: 43 Celsius Lifetime Max Temperature: 50 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 10/55 Celsius Min/Max Temperature Limit: 5/60 Celsius Temperature History Size (Index): 128 (113) Index Estimated Time Temperature Celsius 114 2016-03-09 21:22 42 *********************** ... ..( 2 skipped). .. *********************** 117 2016-03-09 21:25 42 *********************** 118 2016-03-09 21:26 43 ************************ 119 2016-03-09 21:27 42 *********************** 120 2016-03-09 21:28 42 *********************** 121 2016-03-09 21:29 43 ************************ 122 2016-03-09 21:30 42 *********************** 123 2016-03-09 21:31 42 *********************** 124 2016-03-09 21:32 43 ************************ 125 2016-03-09 21:33 43 ************************ 126 2016-03-09 21:34 43 ************************ 127 2016-03-09 21:35 42 *********************** ... ..( 13 skipped). .. *********************** 13 2016-03-09 21:49 42 *********************** 14 2016-03-09 21:50 43 ************************ 15 2016-03-09 21:51 42 *********************** 16 2016-03-09 21:52 43 ************************ 17 2016-03-09 21:53 42 *********************** 18 2016-03-09 21:54 43 ************************ 19 2016-03-09 21:55 43 ************************ 20 2016-03-09 21:56 42 *********************** 21 2016-03-09 21:57 42 *********************** 22 2016-03-09 21:58 43 ************************ 23 2016-03-09 21:59 43 ************************ 24 2016-03-09 22:00 42 *********************** ... ..( 8 skipped). .. *********************** 33 2016-03-09 22:09 42 *********************** 34 2016-03-09 22:10 43 ************************ 35 2016-03-09 22:11 43 ************************ 36 2016-03-09 22:12 42 *********************** 37 2016-03-09 22:13 42 *********************** 38 2016-03-09 22:14 43 ************************ 39 2016-03-09 22:15 42 *********************** 40 2016-03-09 22:16 43 ************************ 41 2016-03-09 22:17 43 ************************ 42 2016-03-09 22:18 42 *********************** 43 2016-03-09 22:19 43 ************************ 44 2016-03-09 22:20 43 ************************ 45 2016-03-09 22:21 42 *********************** 46 2016-03-09 22:22 43 ************************ ... ..( 13 skipped). .. ************************ 60 2016-03-09 22:36 43 ************************ 61 2016-03-09 22:37 ? - 62 2016-03-09 22:38 43 ************************ 63 2016-03-09 22:39 42 *********************** 64 2016-03-09 22:40 42 *********************** 65 2016-03-09 22:41 42 *********************** 66 2016-03-09 22:42 43 ************************ 67 2016-03-09 22:43 42 *********************** ... ..( 5 skipped). .. *********************** 73 2016-03-09 22:49 42 *********************** 74 2016-03-09 22:50 43 ************************ 75 2016-03-09 22:51 43 ************************ 76 2016-03-09 22:52 43 ************************ 77 2016-03-09 22:53 42 *********************** ... ..( 2 skipped). .. *********************** 80 2016-03-09 22:56 42 *********************** 81 2016-03-09 22:57 41 ********************** ... ..( 3 skipped). .. ********************** 85 2016-03-09 23:01 41 ********************** 86 2016-03-09 23:02 40 ********************* ... ..( 5 skipped). .. ********************* 92 2016-03-09 23:08 40 ********************* 93 2016-03-09 23:09 39 ******************** ... ..( 19 skipped). .. ******************** 113 2016-03-09 23:29 39 ******************** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x8001 2 0 Vendor specific