/dev/sda smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.2-desktop-1omv2390] (OpenMandriva Lx 7.4-1) Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA Device Model: WDC WD3200BEVT-22A23T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 320,072,933,376 bytes [320 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Device is: In smartctl database ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Apr 27 08:57:31 2024 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 7800) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 93) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 183 3 Spin_Up_Time POS--K 152 128 021 - 1358 4 Start_Stop_Count -O--CK 037 037 000 - 63481 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 090 090 000 - 7713 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3866 191 G-Sense_Error_Rate -O--CK 001 001 000 - 16750 192 Power-Off_Retract_Count -O--CK 200 200 000 - 420 193 Load_Cycle_Count -O--CK 001 001 000 - 904542 194 Temperature_Celsius -O---K 114 085 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 1 198 Offline_Uncorrectable ----CK 200 200 000 - 1 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 1 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 24 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 193 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 193 [0] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 40 00 00 03 07 36 b8 40 08 00:36:20.960 READ FPDMA QUEUED 60 00 08 00 38 00 00 1d 08 78 90 40 08 00:36:20.960 READ FPDMA QUEUED 61 00 08 00 30 00 00 12 fd e5 68 40 08 00:36:20.959 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:20.947 FLUSH CACHE EXT 60 00 08 00 90 00 00 1c fe 2a a8 40 08 00:36:20.924 READ FPDMA QUEUED Error 192 [23] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 78 00 00 1d 08 78 90 40 08 00:36:18.271 READ FPDMA QUEUED 61 00 18 00 68 00 00 12 fd e5 50 40 08 00:36:18.271 WRITE FPDMA QUEUED 60 00 08 00 60 00 00 1c fe 2a a8 40 08 00:36:18.271 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:18.271 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:36:18.269 SET FEATURES [Enable SATA feature] Error 191 [22] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b8 00 00 1d 08 78 90 40 08 00:36:15.624 READ FPDMA QUEUED 60 00 08 00 b0 00 00 01 fd e9 00 40 08 00:36:15.624 READ FPDMA QUEUED 61 00 08 00 a8 00 00 12 fd e5 48 40 08 00:36:15.624 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:15.584 FLUSH CACHE EXT 60 00 08 00 10 00 00 01 fd e8 f8 40 08 00:36:15.564 READ FPDMA QUEUED Error 190 [21] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 98 00 00 1d 08 78 90 40 08 00:36:12.917 READ FPDMA QUEUED 61 00 18 00 78 00 00 12 fd e5 30 40 08 00:36:12.917 WRITE FPDMA QUEUED 60 00 08 00 68 00 00 01 fd e8 f8 40 08 00:36:12.917 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:36:12.915 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:12.914 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 189 [20] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 38 00 00 01 fd e8 f8 40 08 00:36:10.248 READ FPDMA QUEUED 60 00 08 00 30 00 00 1d 08 78 90 40 08 00:36:10.248 READ FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:10.235 FLUSH CACHE EXT 60 00 08 00 90 00 00 1c fe 2a a0 40 08 00:36:10.212 READ FPDMA QUEUED ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:36:10.210 SET FEATURES [Enable SATA feature] Error 188 [19] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 70 00 00 1c fe 2a a0 40 08 00:36:07.553 READ FPDMA QUEUED 60 00 08 00 68 00 00 1d 08 78 90 40 08 00:36:07.553 READ FPDMA QUEUED 61 00 08 00 60 00 00 12 fd e5 28 40 08 00:36:07.553 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 00:36:07.373 FLUSH CACHE EXT ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:36:07.370 SET FEATURES [Enable SATA feature] Error 187 [18] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b0 00 00 01 fd dc 10 40 08 00:36:04.707 READ FPDMA QUEUED 61 00 08 00 a8 00 00 1c fd eb e8 40 08 00:36:04.707 WRITE FPDMA QUEUED 61 00 28 00 a0 00 00 12 fd e5 00 40 08 00:36:04.707 WRITE FPDMA QUEUED 60 00 08 00 98 00 00 1d 08 78 90 40 08 00:36:04.707 READ FPDMA QUEUED 60 01 00 00 90 00 00 03 1d 73 c8 40 08 00:36:04.694 READ FPDMA QUEUED Error 186 [17] occurred at disk power-on lifetime: 7110 hours (296 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 08 00 00 1d 08 78 96 40 00 Error: UNC at LBA = 0x1d087896 = 487094422 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 08 00 b8 00 00 03 07 a6 b0 40 08 00:36:02.007 READ FPDMA QUEUED 60 00 08 00 b0 00 00 01 fd e8 d8 40 08 00:36:02.006 READ FPDMA QUEUED 60 00 08 00 a8 00 00 1d 08 78 90 40 08 00:36:02.005 READ FPDMA QUEUED 61 00 08 00 a0 00 00 1c fa d9 80 40 08 00:36:02.005 WRITE FPDMA QUEUED 61 00 08 00 98 00 00 1c f9 e0 60 40 08 00:36:02.005 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: read failure 50% 7657 487094422 # 2 Extended offline Completed: read failure 90% 7656 487094422 # 3 Short offline Completed: read failure 10% 7655 487094422 # 4 Short offline Completed: read failure 10% 7653 487094422 # 5 Extended offline Completed: read failure 90% 7632 487094422 # 6 Short offline Completed: read failure 10% 7630 487094422 # 7 Short offline Completed: read failure 90% 7630 487094422 # 8 Short offline Completed: read failure 90% 7628 487094422 # 9 Short offline Completed: read failure 90% 7621 487094422 #10 Short offline Completed: read failure 90% 7618 487094422 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 29 Celsius Power Cycle Min/Max Temperature: 22/29 Celsius Lifetime Min/Max Temperature: 23/57 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (107) Index Estimated Time Temperature Celsius 108 2024-04-27 06:50 47 **************************** ... ..( 4 skipped). .. **************************** 113 2024-04-27 06:55 47 **************************** 114 2024-04-27 06:56 46 *************************** ... ..( 8 skipped). .. *************************** 123 2024-04-27 07:05 46 *************************** 124 2024-04-27 07:06 47 **************************** ... ..( 2 skipped). .. **************************** 127 2024-04-27 07:09 47 **************************** 0 2024-04-27 07:10 46 *************************** 1 2024-04-27 07:11 47 **************************** ... ..( 11 skipped). .. **************************** 13 2024-04-27 07:23 47 **************************** 14 2024-04-27 07:24 48 ***************************** 15 2024-04-27 07:25 47 **************************** ... ..( 4 skipped). .. **************************** 20 2024-04-27 07:30 47 **************************** 21 2024-04-27 07:31 48 ***************************** ... ..( 2 skipped). .. ***************************** 24 2024-04-27 07:34 48 ***************************** 25 2024-04-27 07:35 47 **************************** 26 2024-04-27 07:36 48 ***************************** ... ..( 56 skipped). .. ***************************** 83 2024-04-27 08:33 48 ***************************** 84 2024-04-27 08:34 49 ****************************** 85 2024-04-27 08:35 48 ***************************** ... ..( 4 skipped). .. ***************************** 90 2024-04-27 08:40 48 ***************************** 91 2024-04-27 08:41 49 ****************************** 92 2024-04-27 08:42 ? - 93 2024-04-27 08:43 23 **** 94 2024-04-27 08:44 23 **** 95 2024-04-27 08:45 24 ***** 96 2024-04-27 08:46 25 ****** 97 2024-04-27 08:47 ? - 98 2024-04-27 08:48 26 ******* 99 2024-04-27 08:49 ? - 100 2024-04-27 08:50 22 *** 101 2024-04-27 08:51 23 **** 102 2024-04-27 08:52 25 ****** 103 2024-04-27 08:53 26 ******* 104 2024-04-27 08:54 27 ******** 105 2024-04-27 08:55 28 ********* 106 2024-04-27 08:56 28 ********* 107 2024-04-27 08:57 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x8000 4 446 Vendor specific