/dev/sda === START OF INFORMATION SECTION === Model Family: Hitachi Travelstar 5K160 Device Model: Hitachi HTS541612J9SA00 Serial Number: -- LU WWN Device Id: 5 000cca ... Firmware Version: SBDOC70P User Capacity: 120 034 123 776 bytes [120 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Wed Feb 3 20:39:24 2016 SAMT SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM level is: 128 (minimum power consumption without standby) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 645) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 73) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate PO-R-- 100 100 062 - 0 2 Throughput_Performance P-S--- 100 100 040 - 0 3 Spin_Up_Time POS--- 245 245 033 - 1 4 Start_Stop_Count -O--C- 096 096 000 - 6426 5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0 7 Seek_Error_Rate PO-R-- 100 100 067 - 0 8 Seek_Time_Performance P-S--- 100 100 040 - 0 9 Power_On_Hours -O--C- 056 056 000 - 19532 10 Spin_Retry_Count PO--C- 100 100 060 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 6307 191 G-Sense_Error_Rate -O-R-- 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 099 099 000 - 232 193 Load_Cycle_Count -O--C- 076 076 000 - 240949 194 Temperature_Celsius -O---- 144 144 000 - 38 (Min/Max 5/51) 196 Reallocated_Event_Count -O--CK 100 100 000 - 4 197 Current_Pending_Sector -O---K 100 100 000 - 0 198 Offline_Uncorrectable ---R-- 100 100 000 - 0 199 UDMA_CRC_Error_Count -O-R-- 200 253 000 - 0 223 Load_Retry_Count -O-R-- 100 100 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 1 Comprehensive SMART error log 0x03 GPL R/O 1 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters 0x80-0x9f GPL,SL R/W 16 Host vendor specific log SMART Extended Comprehensive Error Log Version: 1 (1 sectors) Device Error Count: 94 (device log contains only the most recent 4 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 94 [1] occurred at disk power-on lifetime: 18548 hours (772 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 00 00 00 03 48 d2 e0 00 Error: UNC 6 sectors at LBA = 0x000348d2 = 215250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 00 03 48 d0 e0 00 01:12:27.100 READ DMA e7 00 00 00 00 45 63 47 00 00 00 a0 00 01:12:27.100 FLUSH CACHE ca 00 00 00 08 3b 73 2f 45 63 40 e4 00 01:12:27.100 WRITE DMA ca 00 00 00 08 40 f5 73 3b 73 28 e4 00 01:12:27.100 WRITE DMA c8 00 00 00 04 45 47 49 40 f5 70 e4 00 01:12:27.100 READ DMA Error 93 [0] occurred at disk power-on lifetime: 18548 hours (772 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 45 47 00 03 48 d2 e0 00 Error: UNC 6 sectors at LBA = 0x4547000348d2 = 76171245209810 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 45 47 51 03 48 d0 e0 00 01:12:23.100 READ DMA ca 00 00 00 01 3e 61 37 45 47 51 e4 00 01:12:23.100 WRITE DMA ca 00 00 00 08 3e 61 3f 3e 61 30 e4 00 01:12:23.100 WRITE DMA ca 00 00 00 08 3e 61 47 3e 61 38 e4 00 01:12:23.100 WRITE DMA ca 00 00 00 08 2d 3f ff 3e 61 40 e4 00 01:12:23.100 WRITE DMA Error 92 [3] occurred at disk power-on lifetime: 18548 hours (772 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 41 6f 00 03 48 d2 e0 00 Error: UNC 6 sectors at LBA = 0x416f000348d2 = 71944997390546 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 41 6f 09 03 48 d0 e0 00 01:12:18.300 READ DMA c8 00 00 00 08 2d 3f f7 41 6f 02 e0 00 01:12:18.300 READ DMA c8 00 00 00 08 45 44 f8 2d 3f f0 e0 00 01:12:18.300 READ DMA c8 00 00 00 01 45 45 03 45 44 f8 e4 00 01:12:18.300 READ DMA c8 00 00 00 04 35 2d 8f 45 45 00 e4 00 01:12:18.200 READ DMA Error 91 [2] occurred at disk power-on lifetime: 18548 hours (772 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 06 41 6e 00 03 48 d2 e0 00 Error: UNC 6 sectors at LBA = 0x416e000348d2 = 71940702423250 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 41 6e 39 03 48 d0 e0 00 01:12:14.200 READ DMA c8 00 00 00 08 2d 3f df 41 6e 32 e0 00 01:12:14.100 READ DMA c8 00 00 00 08 03 40 30 2d 3f d8 e0 00 01:12:14.100 READ DMA ca 00 00 00 01 63 95 c3 03 40 30 e0 00 01:12:14.100 WRITE DMA ca 00 00 00 14 63 95 af 63 95 b0 e1 00 01:12:14.100 WRITE DMA SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 90% 13500 - # 2 Short offline Aborted by host 80% 13177 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Commands not supported Device Statistics (GP Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0009 2 4 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 4 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS