/dev/sda smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-106-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-75WN4A1 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 13057113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 17 23:05:04 2024 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (11100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 115) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 192 051 - 0 3 Spin_Up_Time POS--K 174 168 021 - 2291 4 Start_Stop_Count -O--CK 099 099 000 - 1078 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 093 093 000 - 5813 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1074 192 Power-Off_Retract_Count -O--CK 200 200 000 - 113 193 Load_Cycle_Count -O--CK 185 185 000 - 47616 194 Temperature_Celsius -O---K 116 099 000 - 27 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 240 Head_Flying_Hours -O--CK 093 093 000 - 5310 241 Total_LBAs_Written -O--CK 200 200 000 - 56416360351 242 Total_LBAs_Read -O--CK 200 200 000 - 49766040257 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 48 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 368 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 368 [7] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3f e0 00 Error: UNC 1 sectors at LBA = 0x0268323f = 40383039 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3f e0 08 00:03:47.018 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:47.018 WRITE DMA EXT 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:47.018 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3f e0 08 00:03:43.515 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:43.515 READ DMA EXT Error 367 [6] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3f e0 00 Error: UNC 1 sectors at LBA = 0x0268323f = 40383039 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3f e0 08 00:03:43.515 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:43.515 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:43.515 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:43.515 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:43.515 WRITE DMA EXT Error 366 [5] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3e e0 00 Error: UNC 1 sectors at LBA = 0x0268323e = 40383038 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:39.842 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:39.842 WRITE DMA EXT 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:39.842 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:36.343 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:36.343 READ DMA EXT Error 365 [4] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3e e0 00 Error: UNC 1 sectors at LBA = 0x0268323e = 40383038 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3e e0 08 00:03:36.343 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:36.343 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:36.343 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:36.343 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:36.342 WRITE DMA EXT Error 364 [3] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3d e0 00 Error: UNC 1 sectors at LBA = 0x0268323d = 40383037 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:32.741 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:32.740 WRITE DMA EXT 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:32.740 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:29.238 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:29.237 READ DMA EXT Error 363 [2] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3d e0 00 Error: UNC 1 sectors at LBA = 0x0268323d = 40383037 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3d e0 08 00:03:29.238 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:29.237 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:29.237 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:29.237 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:29.237 WRITE DMA EXT Error 362 [1] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3c e0 00 Error: UNC 1 sectors at LBA = 0x0268323c = 40383036 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:25.556 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:25.556 WRITE DMA EXT 25 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:25.556 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:22.053 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:22.053 READ DMA EXT Error 361 [0] occurred at disk power-on lifetime: 375 hours (15 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 01 00 00 02 68 32 3c e0 00 Error: UNC 1 sectors at LBA = 0x0268323c = 40383036 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 20 20 00 01 00 00 02 68 32 3c e0 08 00:03:22.053 READ DMA EXT 25 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:22.053 READ DMA EXT 35 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:22.053 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3a e0 08 00:03:22.053 WRITE DMA EXT 35 20 20 00 01 00 00 02 68 32 3b e0 08 00:03:22.052 WRITE DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 27 Celsius Power Cycle Min/Max Temperature: 24/37 Celsius Lifetime Min/Max Temperature: 12/44 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (337) Index Estimated Time Temperature Celsius 338 2024-05-17 15:08 27 ******** ... ..(476 skipped). .. ******** 337 2024-05-17 23:05 27 ******** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 17 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 19 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 782146 Vendor specific /dev/sdb smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-106-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD10EZEX-00RKKA0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 17 23:05:04 2024 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (10620) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 122) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x30b5) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 175 170 021 - 2216 4 Start_Stop_Count -O--CK 096 096 000 - 4766 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 058 058 000 - 30879 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 096 096 000 - 4749 192 Power-Off_Retract_Count -O--CK 200 200 000 - 399 193 Load_Cycle_Count -O--CK 199 199 000 - 4366 194 Temperature_Celsius -O---K 113 092 000 - 30 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb5 GPL,SL VS 1 Device vendor specific log 0xb6 GPL VS 1 Device vendor specific log 0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 17 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 17 [16] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 a0 08 02:58:33.382 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:33.380 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:28.013 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 08 02:58:28.011 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:28.009 IDENTIFY DEVICE Error 16 [15] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 a0 08 02:58:28.011 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:28.009 IDENTIFY DEVICE ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.826 IDENTIFY DEVICE ef 00 03 00 45 00 00 00 00 00 00 a0 08 02:58:22.824 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.822 IDENTIFY DEVICE Error 15 [14] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 45 00 00 00 00 00 00 a0 08 02:58:22.824 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.822 IDENTIFY DEVICE 35 00 00 00 08 00 00 3a 24 18 00 e0 08 02:58:22.637 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.635 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.632 SET FEATURES [Set transfer mode] Error 14 [13] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 08 00 00 3a 24 18 00 e0 00 Device Fault; Error: ABRT 8 sectors at LBA = 0x3a241800 = 975443968 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 35 00 00 00 08 00 00 3a 24 18 00 e0 08 02:58:22.637 WRITE DMA EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.635 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.632 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.630 IDENTIFY DEVICE ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.614 FLUSH CACHE EXT Error 13 [12] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.632 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.630 IDENTIFY DEVICE ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.614 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.611 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.609 SET FEATURES [Set transfer mode] Error 12 [11] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 46 ff 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.614 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.611 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.609 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.606 IDENTIFY DEVICE ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.590 FLUSH CACHE EXT Error 11 [10] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 46 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.609 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.606 IDENTIFY DEVICE ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.590 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.587 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.585 SET FEATURES [Set transfer mode] Error 10 [9] occurred at disk power-on lifetime: 19667 hours (819 days + 11 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 46 ff 00 00 00 00 00 00 a0 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.590 FLUSH CACHE EXT ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.587 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 08 02:58:22.585 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 00 00 00 00 00 a0 08 02:58:22.582 IDENTIFY DEVICE ea 03 00 46 ff 00 00 00 00 00 00 e0 08 02:58:22.570 FLUSH CACHE EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 22466 - # 2 Short offline Completed without error 00% 15598 - # 3 Conveyance offline Completed without error 00% 15598 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 25/38 Celsius Lifetime Min/Max Temperature: 25/51 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (23) Index Estimated Time Temperature Celsius 24 2024-05-17 15:08 29 ********** ... ..( 92 skipped). .. ********** 117 2024-05-17 16:41 29 ********** 118 2024-05-17 16:42 28 ********* ... ..( 45 skipped). .. ********* 164 2024-05-17 17:28 28 ********* 165 2024-05-17 17:29 29 ********** ... ..(199 skipped). .. ********** 365 2024-05-17 20:49 29 ********** 366 2024-05-17 20:50 28 ********* ... ..( 22 skipped). .. ********* 389 2024-05-17 21:13 28 ********* 390 2024-05-17 21:14 29 ********** ... ..( 22 skipped). .. ********** 413 2024-05-17 21:37 29 ********** 414 2024-05-17 21:38 30 *********** ... ..( 52 skipped). .. *********** 467 2024-05-17 22:31 30 *********** 468 2024-05-17 22:32 29 ********** ... ..( 32 skipped). .. ********** 23 2024-05-17 23:05 29 ********** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 17 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 9 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 782125 Vendor specific /dev/sdc smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-106-generic] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST1000DM003-1CH162 Serial Number: -- LU WWN Device Id: 5 000c50 ... Firmware Version: CC44 User Capacity: 1,000,203,804,160 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri May 17 23:05:04 2024 -03 SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Unavailable === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 575) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 110) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 117 099 006 - 119040320 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 099 099 020 - 1889 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 072 060 030 - 14714763 9 Power_On_Hours -O--CK 085 085 000 - 13576 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 099 099 020 - 1948 183 Runtime_Bad_Block -O--CK 099 099 000 - 1 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 0 188 Command_Timeout -O--CK 100 100 000 - 0 0 0 189 High_Fly_Writes -O-RCK 095 095 000 - 5 190 Airflow_Temperature_Cel -O---K 070 052 045 - 30 (Min/Max 24/36) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 228 193 Load_Cycle_Count -O--CK 099 099 000 - 2740 194 Temperature_Celsius -O---K 030 048 000 - 30 (0 9 0 0 0) 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----C- 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 192 000 - 16 240 Head_Flying_Hours ------ 100 253 000 - 13673h+08m+26.973s 241 Total_LBAs_Written ------ 100 253 000 - 15696595675 242 Total_LBAs_Read ------ 100 253 000 - 16706729338 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbd GPL VS 512 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xc4 GPL,SL VS 5 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) No Errors Logged SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 6858 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) Device State: Active (0) Current Temperature: 30 Celsius Power Cycle Min/Max Temperature: 24/36 Celsius Lifetime Min/Max Temperature: 9/48 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 18 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS