/dev/sda === START OF INFORMATION SECTION === Model Family: Western Digital Blue Mobile Device Model: WDC WD10JPVX-22JC3T0 Serial Number: -- LU WWN Device Id: 5 0014ee ... Firmware Version: 01.01A01 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Tue Sep 29 00:48:07 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 96 (intermediate level with standby) Rd look-ahead is: Enabled Write cache is: Disabled DSN feature is: Unavailable ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (17160) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 192) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 199 199 051 - 9349 3 Spin_Up_Time POS--K 181 178 021 - 1916 4 Start_Stop_Count -O--CK 084 084 000 - 16772 5 Reallocated_Sector_Ct PO--CK 133 133 140 NOW 2829 7 Seek_Error_Rate -OSR-K 001 001 000 - 151288 9 Power_On_Hours -O--CK 097 097 000 - 2545 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1130 191 G-Sense_Error_Rate -O--CK 001 001 000 - 6062 192 Power-Off_Retract_Count -O--CK 200 200 000 - 117 193 Load_Cycle_Count -O--CK 193 193 000 - 21373 194 Temperature_Celsius -O---K 111 100 000 - 36 196 Reallocated_Event_Count -O--CK 001 001 000 - 1216 197 Current_Pending_Sector -O--CK 001 001 000 - 65203 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb6 GPL,SL VS 1 Device vendor specific log 0xb7 GPL,SL VS 38 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 18626 (device log contains only the most recent 24 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 18626 [9] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 01 00 08 00 00 63 25 b9 b3 40 00 2d+20:26:13.561 READ FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:13.525 SET FEATURES [Enable write cache] 42 00 00 08 00 00 00 63 25 b9 b3 e0 00 2d+20:26:13.525 READ VERIFY SECTOR(S) EXT 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:12.594 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:12.593 SET FEATURES [Enable write cache] Error 18625 [8] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:13.525 SET FEATURES [Enable write cache] 42 00 00 08 00 00 00 63 25 b9 b3 e0 00 2d+20:26:13.525 READ VERIFY SECTOR(S) EXT 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:12.594 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:12.593 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:11.686 WRITE FPDMA QUEUED Error 18624 [7] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 08 00 00 00 63 25 b9 b3 e0 00 Device Fault; Error: ABRT at LBA = 0x6325b9b3 = 1663416755 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 42 00 00 08 00 00 00 63 25 b9 b3 e0 00 2d+20:26:13.525 READ VERIFY SECTOR(S) EXT 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:12.594 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:12.593 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:11.686 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:11.685 SET FEATURES [Enable write cache] Error 18623 [6] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:12.594 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:12.593 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:11.686 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:11.685 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:10.780 WRITE FPDMA QUEUED Error 18622 [5] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:12.593 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:11.686 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:11.685 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:10.780 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:10.780 SET FEATURES [Enable write cache] Error 18621 [4] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:11.686 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:11.685 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:10.780 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:10.780 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:09.840 WRITE FPDMA QUEUED Error 18620 [3] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:11.685 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:10.780 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:10.780 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:09.840 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:09.839 SET FEATURES [Enable write cache] Error 18619 [2] occurred at disk power-on lifetime: 2542 hours (105 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 04 -- 61 00 00 00 00 00 00 00 00 00 00 Device Fault; Error: ABRT at LBA = 0x00000000 = 0 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:10.780 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:10.780 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:09.840 WRITE FPDMA QUEUED ef 00 02 00 00 00 00 00 00 00 00 00 00 2d+20:26:09.839 SET FEATURES [Enable write cache] 61 00 01 00 08 00 00 63 25 b9 b2 40 00 2d+20:26:08.921 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed: unknown failure 90% 2354 4294967295 # 2 Short offline Completed: unknown failure 90% 2354 4294967295 # 3 Short offline Completed without error 00% 1978 - # 4 Short offline Aborted by host 60% 1915 - # 5 Short offline Completed without error 00% 1893 - # 6 Short offline Completed without error 00% 1516 - # 7 Short offline Completed without error 00% 1384 - # 8 Short offline Completed without error 00% 1267 - # 9 Short offline Completed without error 00% 1014 - #10 Short offline Completed without error 00% 813 - #11 Short offline Completed without error 00% 663 - #12 Short offline Completed without error 00% 247 - #13 Short offline Completed without error 00% 209 - #14 Short offline Completed without error 00% 170 - #15 Short offline Completed without error 00% 100 - #16 Short offline Completed without error 00% 4 - #17 Short offline Completed without error 00% 4 - #18 Short offline Completed without error 00% 4 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 36/37 Celsius Lifetime Min/Max Temperature: 16/47 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 128 (89) Index Estimated Time Temperature Celsius 90 2020-09-28 22:41 35 **************** ... ..( 16 skipped). .. **************** 107 2020-09-28 22:58 35 **************** 108 2020-09-28 22:59 36 ***************** ... ..( 35 skipped). .. ***************** 16 2020-09-28 23:35 36 ***************** 17 2020-09-28 23:36 37 ****************** 18 2020-09-28 23:37 37 ****************** 19 2020-09-28 23:38 37 ****************** 20 2020-09-28 23:39 36 ***************** ... ..( 15 skipped). .. ***************** 36 2020-09-28 23:55 36 ***************** 37 2020-09-28 23:56 37 ****************** ... ..( 2 skipped). .. ****************** 40 2020-09-28 23:59 37 ****************** 41 2020-09-29 00:00 36 ***************** ... ..( 9 skipped). .. ***************** 51 2020-09-29 00:10 36 ***************** 52 2020-09-29 00:11 37 ****************** ... ..( 7 skipped). .. ****************** 60 2020-09-29 00:19 37 ****************** 61 2020-09-29 00:20 ? - 62 2020-09-29 00:21 37 ****************** 63 2020-09-29 00:22 37 ****************** 64 2020-09-29 00:23 36 ***************** ... ..( 24 skipped). .. ***************** 89 2020-09-29 00:48 36 ***************** SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 8 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 1832 Vendor specific