/dev/sda: ATA device, with non-removable media Model Number: ST4000DM005-2DP166 Serial Number: -- Firmware Revision: 0001 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x006d) Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 7814037168 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 3815447 MBytes device size with M = 1000*1000: 4000787 MBytes (4000 GB) cache/buffer size = 8192 KBytes Form Factor: 3.5 inch Nominal Media Rotation Rate: 5980 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: 127 Recommended acoustic management value: 208, current value: 208 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * Media Card Pass-Through * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * IDLE_IMMEDIATE with UNLOAD Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * unknown 119[6] * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * Idle-Unload when NCQ is active * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation unknown 78[7] unknown 78[11] * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) * SCT Data Tables (AC5) unknown 206[7] unknown 206[12] (vendor specific) * SANITIZE_ANTIFREEZE_LOCK_EXT command * SANITIZE feature set * OVERWRITE_EXT command * DOWNLOAD MICROCODE DMA command Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 468min for SECURITY ERASE UNIT. 468min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: -- NAA : 5 IEEE OUI : 000c50 Unique ID : -- Checksum: correct /dev/sdb: ATA device, with non-removable media Model Number: SK hynix SC311 SATA 256GB Serial Number: -- Firmware Revision: 70000P10 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 0 heads 16 0 sectors/track 63 0 -- LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 500118192 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 244198 MBytes device size with M = 1000*1000: 256060 MBytes (256 GB) cache/buffer size = unknown Form Factor: 2.5 inch Nominal Media Rotation Rate: Solid State Device Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set SET_MAX security extension * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * IDLE_IMMEDIATE with UNLOAD * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT Non-Zero buffer offsets in DMA Setup FIS * DMA Setup Auto-Activate optimization * Device-initiated interface power management In-order data delivery * Software settings preservation Device Sleep (DEVSLP) * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) * SANITIZE feature set * CRYPTO_SCRAMBLE_EXT command * BLOCK_ERASE_EXT command * reserved 69[4] * DOWNLOAD MICROCODE DMA command * WRITE BUFFER DMA command * READ BUFFER DMA command * Data Set Management TRIM supported (limit 8 blocks) * Deterministic read ZEROs after TRIM Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 2min for SECURITY ERASE UNIT. 2min for ENHANCED SECURITY ERASE UNIT. Checksum: correct /dev/sdc: ATA device, with non-removable media Model Number: ST10000DM0004-1ZC101 Serial Number: -- Firmware Revision: DN01 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x006d) Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 19532873728 Logical Sector size: 512 bytes Physical Sector size: 4096 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 9537536 MBytes device size with M = 1000*1000: 10000831 MBytes (10000 GB) cache/buffer size = unknown Form Factor: 3.5 inch Nominal Media Rotation Rate: 7200 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension * 48-bit Address feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * Media Card Pass-Through * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * IDLE_IMMEDIATE with UNLOAD Write-Read-Verify feature set * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * unknown 119[6] * unknown 119[7] unknown 119[8] * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters * Idle-Unload when NCQ is active * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT * DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation unknown 78[7] unknown 78[11] * SMART Command Transport (SCT) feature set * SCT Write Same (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) unknown 206[7] unknown 206[12] (vendor specific) unknown 206[14] (vendor specific) * SANITIZE_ANTIFREEZE_LOCK_EXT command * SANITIZE feature set * OVERWRITE_EXT command * reserved 69[3] Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 902min for SECURITY ERASE UNIT. 902min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: -- NAA : 5 IEEE OUI : 000c50 Unique ID : -- Checksum: correct /dev/sdd: ATA device, with non-removable media Model Number: KINGSTON SA400S37120G Serial Number: -- Firmware Revision: 03070009 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0 Standards: Used: unknown (minor revision code 0x011b) Supported: 10 9 8 7 6 5 Likely used: 10 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 234441648 LBA48 user addressable sectors: 234441648 Logical Sector size: 512 bytes Physical Sector size: 512 bytes Logical Sector-0 offset: 0 bytes device size with M = 1024*1024: 114473 MBytes device size with M = 1000*1000: 120034 MBytes (120 GB) cache/buffer size = unknown Nominal Media Rotation Rate: Solid State Device Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 1 Current = 1 Advanced power management level: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set * 48-bit Address feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Gen3 signaling speed (6.0Gb/s) * Native Command Queueing (NCQ) * Phy event counters * READ_LOG_DMA_EXT equivalent to READ_LOG_EXT * DMA Setup Auto-Activate optimization * Device-initiated interface power management * Software settings preservation * WRITE BUFFER DMA command * READ BUFFER DMA command * Data Set Management TRIM supported (limit 8 blocks) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 6min for SECURITY ERASE UNIT. 6min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: -- NAA : 5 IEEE OUI : 02b2a2 Unique ID : -- Checksum: correct