[ 0.000000] Linux version 5.0.0-31-generic (XXX@XXX) (gcc version 7.4.0 (Ubuntu 7.4.0-1ubuntu1~18.04.1)) #33~18.04.1-Ubuntu SMP Tue Oct 1 10:18:51 UTC 2019 (Ubuntu 5.0.0-31.33~18.04.1-generic 5.0.21) [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Hygon HygonGenuine [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] x86/fpu: x87 FPU will use FXSAVE [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009dfff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007da6bfff] usable [ 0.000000] BIOS-e820: [mem 0x000000007da6c000-0x000000007dabefff] reserved [ 0.000000] BIOS-e820: [mem 0x000000007dabf000-0x000000007db82fff] usable [ 0.000000] BIOS-e820: [mem 0x000000007db83000-0x000000007dbbefff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x000000007dbbf000-0x000000007dbe7fff] usable [ 0.000000] BIOS-e820: [mem 0x000000007dbe8000-0x000000007dbfefff] ACPI data [ 0.000000] BIOS-e820: [mem 0x000000007dbff000-0x000000007dbfffff] usable [ 0.000000] BIOS-e820: [mem 0x000000007dc00000-0x000000007fffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed13fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed18000-0x00000000fed19fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.4 present. [ 0.000000] DMI: Hewlett-Packard HP Pavilion dv4 /30F7, BIOS F.13 10/01/2008 [ 0.000000] tsc: Fast TSC calibration using PIT [ 0.000000] tsc: Detected 1994.850 MHz processor [ 0.013805] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.013808] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.013819] last_pfn = 0x7dc00 max_arch_pfn = 0x1000000 [ 0.013828] MTRR default type: uncachable [ 0.013829] MTRR fixed ranges enabled: [ 0.013831] 00000-9FFFF write-back [ 0.013833] A0000-FFFFF uncachable [ 0.013834] MTRR variable ranges enabled: [ 0.013836] 0 base 000000000 mask FC0000000 write-back [ 0.013838] 1 base 040000000 mask FC0000000 write-back [ 0.013840] 2 base 07E000000 mask FFE000000 uncachable [ 0.013842] 3 base 07DC00000 mask FFFC00000 uncachable [ 0.013843] 4 disabled [ 0.013843] 5 disabled [ 0.013845] 6 base 0FFF00000 mask FFFF00000 write-protect [ 0.013846] 7 disabled [ 0.014723] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.030155] check: Scanning 1 areas for low memory corruption [ 0.030158] initial memory mapped: [mem 0x00000000-0x1b3fffff] [ 0.030243] BRK [0x1b0a1000, 0x1b0a1fff] PGTABLE [ 0.030266] BRK [0x1b0a2000, 0x1b0a2fff] PGTABLE [ 0.030270] RAMDISK: [mem 0x335a3000-0x35ac8fff] [ 0.030283] ACPI: Early table checksum verification disabled [ 0.031217] ACPI: RSDP 0x00000000000FE020 000024 (v02 HP ) [ 0.031223] ACPI: XSDT 0x000000007DBFE120 00006C (v01 HPQOEM SLIC-MPC 00000001 01000013) [ 0.031231] ACPI: FACP 0x000000007DBFC000 0000F4 (v04 HP BLADE 00000001 MSFT 01000013) [ 0.031239] ACPI: DSDT 0x000000007DBED000 00A5A3 (v01 HP BLADE 00000001 MSFT 01000013) [ 0.031244] ACPI: FACS 0x000000007DB8C000 000040 [ 0.031248] ACPI: FACS 0x000000007DB8C000 000040 [ 0.031252] ACPI: SSDT 0x000000007DBFD000 000655 (v01 PmRef CpuPm 00003000 INTL 20060912) [ 0.031258] ACPI: HPET 0x000000007DBFB000 000038 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.031263] ACPI: APIC 0x000000007DBFA000 00006C (v02 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.031268] ACPI: MCFG 0x000000007DBF9000 00003C (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.031273] ACPI: ASF! 0x000000007DBF8000 0000A5 (v32 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.031278] ACPI: SLIC 0x000000007DBEC000 000176 (v01 HPQOEM SLIC-MPC 00000001 LOHR 000F4240) [ 0.031283] ACPI: BOOT 0x000000007DBEB000 000028 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.031288] ACPI: SSDT 0x000000007DBEA000 000296 (v01 INTEL SataAhci 00001000 INTL 20060912) [ 0.031316] ACPI: Local APIC address 0xfee00000 [ 0.031322] 1126MB HIGHMEM available. [ 0.031325] 885MB LOWMEM available. [ 0.031326] mapped low ram: 0 - 375fe000 [ 0.031327] low ram: 0 - 375fe000 [ 0.031336] BRK [0x1b0a3000, 0x1b0a3fff] PGTABLE [ 0.033640] Zone ranges: [ 0.033641] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.033644] Normal [mem 0x0000000001000000-0x00000000375fdfff] [ 0.033645] HighMem [mem 0x00000000375fe000-0x000000007dbfffff] [ 0.033647] Movable zone start for each node [ 0.033648] Early memory node ranges [ 0.033650] node 0: [mem 0x0000000000001000-0x000000000009dfff] [ 0.033651] node 0: [mem 0x0000000000100000-0x000000007da6bfff] [ 0.033652] node 0: [mem 0x000000007dabf000-0x000000007db82fff] [ 0.033653] node 0: [mem 0x000000007dbbf000-0x000000007dbe7fff] [ 0.033655] node 0: [mem 0x000000007dbff000-0x000000007dbfffff] [ 0.033664] Zeroed struct page in unavailable ranges: 265 pages [ 0.033666] Initmem setup node 0 [mem 0x0000000000001000-0x000000007dbfffff] [ 0.033668] On node 0 totalpages: 514807 [ 0.033670] DMA zone: 40 pages used for memmap [ 0.033671] DMA zone: 0 pages reserved [ 0.033673] DMA zone: 3997 pages, LIFO batch:0 [ 0.033798] Normal zone: 2175 pages used for memmap [ 0.033799] Normal zone: 222718 pages, LIFO batch:63 [ 0.040576] HighMem zone: 288092 pages, LIFO batch:63 [ 0.049409] Using APIC driver default [ 0.049423] Reserving Intel graphics memory at [mem 0x7e000000-0x7fffffff] [ 0.049895] ACPI: PM-Timer IO Port: 0x408 [ 0.049898] ACPI: Local APIC address 0xfee00000 [ 0.049920] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 [ 0.049923] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.049926] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.049928] ACPI: IRQ0 used by override. [ 0.049930] ACPI: IRQ9 used by override. [ 0.049933] Using ACPI (MADT) for SMP configuration information [ 0.049935] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.049946] smpboot: Allowing 4 CPUs, 2 hotplug CPUs [ 0.049976] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.049979] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff] [ 0.049980] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff] [ 0.049981] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff] [ 0.049983] PM: Registered nosave memory: [mem 0x7da6c000-0x7dabefff] [ 0.049985] PM: Registered nosave memory: [mem 0x7db83000-0x7dbbefff] [ 0.049987] PM: Registered nosave memory: [mem 0x7dbe8000-0x7dbfefff] [ 0.049991] [mem 0x80000000-0xf7ffffff] available for PCI devices [ 0.049992] Booting paravirtualized kernel on bare hardware [ 0.049998] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.050017] random: get_random_bytes called from start_kernel+0x81/0x479 with crng_init=0 [ 0.050027] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1 [ 0.050409] percpu: Embedded 31 pages/cpu s95244 r0 d31732 u126976 [ 0.050419] pcpu-alloc: s95244 r0 d31732 u126976 alloc=31*4096 [ 0.050420] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.050446] Built 1 zonelists, mobility grouping on. Total pages: 512592 [ 0.050450] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.0.0-31-generic root=/dev/mapper/XXXXXXXXXXXXXXXX ro quiet splash vt.handoff=1 [ 0.050918] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.051055] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.051101] microcode: microcode updated early to revision 0xa4, date = 2010-10-02 [ 0.051102] Initializing CPU#0 [ 0.090713] Initializing HighMem for node 0 (000375fe:0007dc00) [ 0.188845] Initializing Movable for node 0 (00000000:00000000) [ 0.195826] Memory: 1912280K/2059228K available (9465K kernel code, 905K rwdata, 3636K rodata, 1128K init, 872K bss, 146948K reserved, 0K cma-reserved, 1152368K highmem) [ 0.195831] virtual kernel memory layout: [ 0.195831] fixmap : 0xfff14000 - 0xfffff000 ( 940 kB) [ 0.195831] cpu_entry : 0xffa00000 - 0xffb31000 (1220 kB) [ 0.195831] pkmap : 0xff600000 - 0xff800000 (2048 kB) [ 0.195831] vmalloc : 0xf7dfe000 - 0xff5fe000 ( 120 MB) [ 0.195831] lowmem : 0xc0000000 - 0xf75fe000 ( 885 MB) [ 0.195831] .init : 0xdadc9000 - 0xdaee3000 (1128 kB) [ 0.195831] .data : 0xda93e548 - 0xdadb4500 (4567 kB) [ 0.195831] .text : 0xda000000 - 0xda93e548 (9465 kB) [ 0.195833] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.196122] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.196127] Kernel/User page tables isolation: enabled [ 0.196142] ftrace: allocating 39754 entries in 78 pages [ 0.229671] rcu: Hierarchical RCU implementation. [ 0.229673] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.229674] Tasks RCU enabled. [ 0.229676] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.229677] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.233663] NR_IRQS: 2304, nr_irqs: 456, preallocated irqs: 16 [ 0.233844] CPU 0 irqstacks, hard=(ptrval) soft=(ptrval) [ 0.233904] vt handoff: transparent VT on vt#1 [ 0.233914] Console: colour dummy device 80x25 [ 0.233921] printk: console [tty0] enabled [ 0.233936] ACPI: Core revision 20181213 [ 0.234190] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns [ 0.234202] hpet clockevent registered [ 0.234208] APIC: Switch to symmetric I/O mode setup [ 0.234209] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.234629] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.254208] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x39825ad5ef2, max_idle_ns: 881590624955 ns [ 0.254226] Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.70 BogoMIPS (lpj=7979400) [ 0.254229] pid_max: default: 32768 minimum: 301 [ 0.254287] LSM: Security Framework initializing [ 0.254304] Yama: becoming mindful. [ 0.254333] AppArmor: AppArmor initialized [ 0.254386] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.254391] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.254743] mce: CPU0: Thermal monitoring enabled (TM1) [ 0.254746] process: using mwait in idle threads [ 0.254753] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4 [ 0.254754] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0 [ 0.254756] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.254758] Spectre V2 : Mitigation: Full generic retpoline [ 0.254759] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.254760] Speculative Store Bypass: Vulnerable [ 0.254793] MDS: Vulnerable: Clear CPU buffers attempted, no microcode [ 0.254990] Freeing SMP alternatives memory: 36K [ 0.369331] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU T5800 @ 2.00GHz (family: 0x6, model: 0xf, stepping: 0xd) [ 0.369508] Performance Events: PEBS fmt0+, Core2 events, 4-deep LBR, Intel PMU driver. [ 0.369517] core: PEBS disabled due to CPU errata [ 0.369520] ... version: 2 [ 0.369521] ... bit width: 40 [ 0.369521] ... generic registers: 2 [ 0.369523] ... value mask: 000000ffffffffff [ 0.369524] ... max period: 000000007fffffff [ 0.369525] ... fixed-purpose events: 3 [ 0.369526] ... event mask: 0000000700000003 [ 0.369587] rcu: Hierarchical SRCU implementation. [ 0.370211] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. [ 0.370211] smp: Bringing up secondary CPUs ... [ 0.370211] CPU 1 irqstacks, hard=(ptrval) soft=(ptrval) [ 0.370211] x86: Booting SMP configuration: [ 0.370211] .... node #0, CPUs: #1 [ 0.004340] Initializing CPU#1 [ 0.370292] smp: Brought up 1 node, 2 CPUs [ 0.370292] smpboot: Max logical packages: 2 [ 0.370292] smpboot: Total of 2 processors activated (7979.40 BogoMIPS) [ 0.372171] allocated 2097152 bytes of page_ext [ 0.372304] devtmpfs: initialized [ 0.374318] PM: Registering ACPI NVS region [mem 0x7db83000-0x7dbbefff] (245760 bytes) [ 0.374429] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.374429] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.374429] pinctrl core: initialized pinctrl subsystem [ 0.374508] RTC time: 11:11:14, date: 2019-10-13 [ 0.374655] NET: Registered protocol family 16 [ 0.374887] EISA bus registered [ 0.374887] cpuidle: using governor ladder [ 0.374887] cpuidle: using governor menu [ 0.374887] Simple Boot Flag value 0x5 read from CMOS RAM was invalid [ 0.374887] Simple Boot Flag at 0x44 set to 0x1 [ 0.374887] ACPI: bus type PCI registered [ 0.374887] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.374887] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000) [ 0.374887] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820 [ 0.374887] PCI: Using MMCONFIG for extended config space [ 0.374887] PCI: Using configuration type 1 for base access [ 0.374887] mtrr: your CPUs had inconsistent variable MTRR settings [ 0.374887] mtrr: probably your BIOS does not setup all CPUs. [ 0.374887] mtrr: corrected configuration. [ 0.378464] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.378464] ACPI: Added _OSI(Module Device) [ 0.378464] ACPI: Added _OSI(Processor Device) [ 0.378464] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.378464] ACPI: Added _OSI(Processor Aggregator Device) [ 0.378464] ACPI: Added _OSI(Linux-Dell-Video) [ 0.378464] ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio) [ 0.378464] ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics) [ 0.387009] ACPI: 3 ACPI AML tables successfully acquired and loaded [ 0.388854] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored [ 0.395014] ACPI: Dynamic OEM Table Load: [ 0.395022] ACPI: SSDT 0x00000000EE889000 000265 (v01 PmRef Cpu0Ist 00003000 INTL 20060912) [ 0.395431] ACPI: Dynamic OEM Table Load: [ 0.395438] ACPI: SSDT 0x00000000EF00C800 000594 (v01 PmRef Cpu0Cst 00003001 INTL 20060912) [ 0.396146] ACPI: Dynamic OEM Table Load: [ 0.396153] ACPI: SSDT 0x00000000EE85BA00 0001CF (v01 PmRef ApIst 00003000 INTL 20060912) [ 0.396464] ACPI: Dynamic OEM Table Load: [ 0.396470] ACPI: SSDT 0x00000000EF0FD840 00008D (v01 PmRef ApCst 00003000 INTL 20060912) [ 0.397080] ACPI: EC: EC started [ 0.397081] ACPI: EC: interrupt blocked [ 0.439281] ACPI: \_SB_.PCI0.LPC_.EC0_: Used as first EC [ 0.439284] ACPI: \_SB_.PCI0.LPC_.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62 [ 0.439286] ACPI: \_SB_.PCI0.LPC_.EC0_: Used as boot DSDT EC to handle transactions [ 0.439287] ACPI: Interpreter enabled [ 0.439328] ACPI: (supports S0 S3 S4 S5) [ 0.439329] ACPI: Using IOAPIC for interrupt routing [ 0.439372] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.439731] ACPI: Enabled 14 GPEs in block 00 to 3F [ 0.467883] ACPI: Power Resource [FN00] (on) [ 0.630679] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) [ 0.630685] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.630693] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM [ 0.630697] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge [ 0.631352] PCI host bridge to bus 0000:00 [ 0.631356] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.631358] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.631360] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.631362] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff window] [ 0.631364] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.631376] pci 0000:00:00.0: [8086:2a40] type 00 class 0x060000 [ 0.631412] DMAR: Disabling IOMMU for graphics on this chipset [ 0.631413] DMAR: Forcing write-buffer flush capability [ 0.631536] pci 0000:00:02.0: [8086:2a42] type 00 class 0x030000 [ 0.631553] pci 0000:00:02.0: reg 0x10: [mem 0x90000000-0x903fffff 64bit] [ 0.631562] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff 64bit pref] [ 0.631569] pci 0000:00:02.0: reg 0x20: [io 0x8110-0x8117] [ 0.631715] pci 0000:00:02.1: [8086:2a43] type 00 class 0x038000 [ 0.631730] pci 0000:00:02.1: reg 0x10: [mem 0x96500000-0x965fffff 64bit] [ 0.631921] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300 [ 0.632015] pci 0000:00:1a.0: reg 0x20: [io 0x80e0-0x80ff] [ 0.632226] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300 [ 0.632314] pci 0000:00:1a.1: reg 0x20: [io 0x80c0-0x80df] [ 0.632529] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320 [ 0.632561] pci 0000:00:1a.7: reg 0x10: [mem 0x9c804c00-0x9c804fff] [ 0.632685] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 0.632827] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300 [ 0.632860] pci 0000:00:1b.0: reg 0x10: [mem 0x9c800000-0x9c803fff 64bit] [ 0.632977] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.633120] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400 [ 0.633235] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.633388] pci 0000:00:1c.1: [8086:2942] type 01 class 0x060400 [ 0.633503] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.633654] pci 0000:00:1c.2: [8086:2944] type 01 class 0x060400 [ 0.633776] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.633929] pci 0000:00:1c.3: [8086:2946] type 01 class 0x060400 [ 0.634041] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.634190] pci 0000:00:1c.4: [8086:2948] type 01 class 0x060400 [ 0.634324] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.634475] pci 0000:00:1c.5: [8086:294a] type 01 class 0x060400 [ 0.634587] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold [ 0.634739] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300 [ 0.634822] pci 0000:00:1d.0: reg 0x20: [io 0x80a0-0x80bf] [ 0.635026] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300 [ 0.635118] pci 0000:00:1d.1: reg 0x20: [io 0x8080-0x809f] [ 0.635321] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300 [ 0.635413] pci 0000:00:1d.2: reg 0x20: [io 0x8060-0x807f] [ 0.635615] pci 0000:00:1d.3: [8086:2939] type 00 class 0x0c0300 [ 0.635708] pci 0000:00:1d.3: reg 0x20: [io 0x8040-0x805f] [ 0.635899] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320 [ 0.635930] pci 0000:00:1d.7: reg 0x10: [mem 0x9c804800-0x9c804bff] [ 0.636054] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.636189] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401 [ 0.636391] pci 0000:00:1f.0: [8086:2919] type 00 class 0x060100 [ 0.636645] pci 0000:00:1f.2: [8086:2929] type 00 class 0x010601 [ 0.636671] pci 0000:00:1f.2: reg 0x10: [io 0x8108-0x810f] [ 0.636682] pci 0000:00:1f.2: reg 0x14: [io 0x811c-0x811f] [ 0.636694] pci 0000:00:1f.2: reg 0x18: [io 0x8100-0x8107] [ 0.636705] pci 0000:00:1f.2: reg 0x1c: [io 0x8118-0x811b] [ 0.636717] pci 0000:00:1f.2: reg 0x20: [io 0x8020-0x803f] [ 0.636729] pci 0000:00:1f.2: reg 0x24: [mem 0x9c804000-0x9c8047ff] [ 0.636794] pci 0000:00:1f.2: PME# supported from D3hot [ 0.636930] pci 0000:00:1f.3: [8086:2930] type 00 class 0x0c0500 [ 0.636959] pci 0000:00:1f.3: reg 0x10: [mem 0x9c805000-0x9c8050ff 64bit] [ 0.636989] pci 0000:00:1f.3: reg 0x20: [io 0x8000-0x801f] [ 0.637197] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.637202] pci 0000:00:1c.0: bridge window [io 0x7000-0x7fff] [ 0.637206] pci 0000:00:1c.0: bridge window [mem 0x9b800000-0x9c7fffff] [ 0.637214] pci 0000:00:1c.0: bridge window [mem 0x90400000-0x913fffff 64bit pref] [ 0.637292] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.637297] pci 0000:00:1c.1: bridge window [io 0x6000-0x6fff] [ 0.637301] pci 0000:00:1c.1: bridge window [mem 0x9a800000-0x9b7fffff] [ 0.637308] pci 0000:00:1c.1: bridge window [mem 0x91400000-0x923fffff 64bit pref] [ 0.637491] pci 0000:03:00.0: [14e4:4315] type 00 class 0x028000 [ 0.637601] pci 0000:03:00.0: reg 0x10: [mem 0x99700000-0x99703fff 64bit] [ 0.637789] pci 0000:03:00.0: enabling Extended Tags [ 0.638045] pci 0000:03:00.0: supports D1 D2 [ 0.638394] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.638398] pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff] [ 0.638403] pci 0000:00:1c.2: bridge window [mem 0x99700000-0x9a7fffff] [ 0.638409] pci 0000:00:1c.2: bridge window [mem 0x92400000-0x933fffff 64bit pref] [ 0.638514] pci 0000:04:00.0: [10ec:8136] type 00 class 0x020000 [ 0.638555] pci 0000:04:00.0: reg 0x10: [io 0x3000-0x30ff] [ 0.638594] pci 0000:04:00.0: reg 0x18: [mem 0x93410000-0x93410fff 64bit pref] [ 0.638619] pci 0000:04:00.0: reg 0x20: [mem 0x93400000-0x9340ffff 64bit pref] [ 0.638636] pci 0000:04:00.0: reg 0x30: [mem 0xfffe0000-0xffffffff pref] [ 0.638759] pci 0000:04:00.0: supports D1 D2 [ 0.638761] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.638941] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.638946] pci 0000:00:1c.3: bridge window [io 0x3000-0x4fff] [ 0.638951] pci 0000:00:1c.3: bridge window [mem 0x98700000-0x996fffff] [ 0.638957] pci 0000:00:1c.3: bridge window [mem 0x93400000-0x944fffff 64bit pref] [ 0.639105] pci 0000:05:00.0: [197b:2382] type 00 class 0x088000 [ 0.639144] pci 0000:05:00.0: reg 0x10: [mem 0x97600300-0x976003ff] [ 0.639462] pci 0000:05:00.2: [197b:2381] type 00 class 0x080501 [ 0.639500] pci 0000:05:00.2: reg 0x10: [mem 0x97600200-0x976002ff] [ 0.639794] pci 0000:05:00.3: [197b:2383] type 00 class 0x088000 [ 0.639831] pci 0000:05:00.3: reg 0x10: [mem 0x97600100-0x976001ff] [ 0.640128] pci 0000:05:00.4: [197b:2384] type 00 class 0x088000 [ 0.640165] pci 0000:05:00.4: reg 0x10: [mem 0x97600000-0x976000ff] [ 0.640502] pci 0000:00:1c.4: PCI bridge to [bus 05] [ 0.640508] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff] [ 0.640512] pci 0000:00:1c.4: bridge window [mem 0x97600000-0x986fffff] [ 0.640519] pci 0000:00:1c.4: bridge window [mem 0x94500000-0x954fffff 64bit pref] [ 0.640591] pci 0000:00:1c.5: PCI bridge to [bus 06-08] [ 0.640595] pci 0000:00:1c.5: bridge window [io 0x1000-0x1fff] [ 0.640600] pci 0000:00:1c.5: bridge window [mem 0x96600000-0x975fffff] [ 0.640608] pci 0000:00:1c.5: bridge window [mem 0x95500000-0x964fffff 64bit pref] [ 0.640634] pci_bus 0000:09: extended config space not accessible [ 0.640713] pci 0000:00:1e.0: PCI bridge to [bus 09] (subtractive decode) [ 0.640727] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7 window] (subtractive decode) [ 0.640729] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff window] (subtractive decode) [ 0.640731] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode) [ 0.640733] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xfebfffff window] (subtractive decode) [ 0.640784] pci_bus 0000:00: on NUMA node 0 [ 0.640934] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641028] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12) [ 0.641119] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641211] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641302] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641393] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641483] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12) [ 0.641574] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. [ 0.650215] ACPI: EC: interrupt unblocked [ 0.650215] ACPI: EC: event unblocked [ 0.650215] ACPI: \_SB_.PCI0.LPC_.EC0_: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62 [ 0.650215] ACPI: \_SB_.PCI0.LPC_.EC0_: Used as boot DSDT EC to handle transactions and events [ 0.650540] SCSI subsystem initialized [ 0.650557] libata version 3.00 loaded. [ 0.650557] pci 0000:00:02.0: vgaarb: setting as boot VGA device [ 0.650557] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.650557] pci 0000:00:02.0: vgaarb: bridge control possible [ 0.650557] vgaarb: loaded [ 0.650557] ACPI: bus type USB registered [ 0.650557] usbcore: registered new interface driver usbfs [ 0.650557] usbcore: registered new interface driver hub [ 0.650557] usbcore: registered new device driver usb [ 0.650557] pps_core: LinuxPPS API ver. 1 registered [ 0.650557] pps_core: Software ver. 5.3.6 - Copyright FAF7-631D Rodolfo Giometti <XXX@XXX> [ 0.650557] PTP clock support registered [ 0.650557] EDAC MC: Ver: 3.0.0 [ 0.650557] PCI: Using ACPI for IRQ routing [ 0.654494] PCI: pci_cache_line_size set to 64 bytes [ 0.654675] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff] [ 0.654677] e820: reserve RAM buffer [mem 0x7da6c000-0x7fffffff] [ 0.654679] e820: reserve RAM buffer [mem 0x7db83000-0x7fffffff] [ 0.654681] e820: reserve RAM buffer [mem 0x7dbe8000-0x7fffffff] [ 0.654683] e820: reserve RAM buffer [mem 0x7dc00000-0x7fffffff] [ 0.654851] NetLabel: Initializing [ 0.654852] NetLabel: domain hash size = 128 [ 0.654853] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.654876] NetLabel: unlabeled traffic allowed by default [ 0.655352] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 0.655360] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.655365] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 0.657408] clocksource: Switched to clocksource tsc-early [ 0.676799] VFS: Disk quotas dquot_6.6.0 [ 0.676829] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.677013] AppArmor: AppArmor Filesystem Enabled [ 0.677083] pnp: PnP ACPI init [ 0.806527] pnp 00:00: disabling [io 0x164e-0x164f] because it overlaps 0000:00:1c.5 BAR 13 [io 0x1000-0x1fff] [ 0.806620] system 00:00: [io 0x0600-0x060f] has been reserved [ 0.806622] system 00:00: [io 0x0610] has been reserved [ 0.806625] system 00:00: [io 0x0800-0x080f] has been reserved [ 0.806627] system 00:00: [io 0x0810-0x0817] has been reserved [ 0.806630] system 00:00: [io 0x0820-0x0823] has been reserved [ 0.806632] system 00:00: [io 0x0400-0x047f] has been reserved [ 0.806634] system 00:00: [io 0x0500-0x053f] has been reserved [ 0.806638] system 00:00: [mem 0xf8000000-0xfbffffff] has been reserved [ 0.806640] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.806643] system 00:00: [mem 0xfed10000-0xfed13fff] has been reserved [ 0.806645] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.806648] system 00:00: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.806651] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.806653] system 00:00: [mem 0xfed20000-0xfed8ffff] has been reserved [ 0.806656] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.806664] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.806729] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.806823] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.806875] pnp 00:03: Plug and Play ACPI device, IDs AUI0216 SYN0100 SYN0002 PNP0f13 (active) [ 0.807027] pnp 00:04: Plug and Play ACPI device, IDs ENE0100 (active) [ 0.807128] pnp: PnP ACPI: found 5 devices [ 0.807132] PnPBIOS: Disabled by ACPI PNP [ 0.844125] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.844132] pci 0000:04:00.0: can't claim BAR 6 [mem 0xfffe0000-0xffffffff pref]: no compatible bridge window [ 0.844203] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.844208] pci 0000:00:1c.0: bridge window [io 0x7000-0x7fff] [ 0.844214] pci 0000:00:1c.0: bridge window [mem 0x9b800000-0x9c7fffff] [ 0.844219] pci 0000:00:1c.0: bridge window [mem 0x90400000-0x913fffff 64bit pref] [ 0.844227] pci 0000:00:1c.1: PCI bridge to [bus 02] [ 0.844230] pci 0000:00:1c.1: bridge window [io 0x6000-0x6fff] [ 0.844237] pci 0000:00:1c.1: bridge window [mem 0x9a800000-0x9b7fffff] [ 0.844242] pci 0000:00:1c.1: bridge window [mem 0x91400000-0x923fffff 64bit pref] [ 0.844250] pci 0000:00:1c.2: PCI bridge to [bus 03] [ 0.844253] pci 0000:00:1c.2: bridge window [io 0x5000-0x5fff] [ 0.844260] pci 0000:00:1c.2: bridge window [mem 0x99700000-0x9a7fffff] [ 0.844265] pci 0000:00:1c.2: bridge window [mem 0x92400000-0x933fffff 64bit pref] [ 0.844277] pci 0000:04:00.0: BAR 6: assigned [mem 0x98700000-0x9871ffff pref] [ 0.844279] pci 0000:00:1c.3: PCI bridge to [bus 04] [ 0.844282] pci 0000:00:1c.3: bridge window [io 0x3000-0x4fff] [ 0.844288] pci 0000:00:1c.3: bridge window [mem 0x98700000-0x996fffff] [ 0.844293] pci 0000:00:1c.3: bridge window [mem 0x93400000-0x944fffff 64bit pref] [ 0.844302] pci 0000:00:1c.4: PCI bridge to [bus 05] [ 0.844304] pci 0000:00:1c.4: bridge window [io 0x2000-0x2fff] [ 0.844311] pci 0000:00:1c.4: bridge window [mem 0x97600000-0x986fffff] [ 0.844315] pci 0000:00:1c.4: bridge window [mem 0x94500000-0x954fffff 64bit pref] [ 0.844323] pci 0000:00:1c.5: PCI bridge to [bus 06-08] [ 0.844326] pci 0000:00:1c.5: bridge window [io 0x1000-0x1fff] [ 0.844332] pci 0000:00:1c.5: bridge window [mem 0x96600000-0x975fffff] [ 0.844336] pci 0000:00:1c.5: bridge window [mem 0x95500000-0x964fffff 64bit pref] [ 0.844344] pci 0000:00:1e.0: PCI bridge to [bus 09] [ 0.844360] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.844362] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.844365] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.844367] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff window] [ 0.844369] pci_bus 0000:01: resource 0 [io 0x7000-0x7fff] [ 0.844370] pci_bus 0000:01: resource 1 [mem 0x9b800000-0x9c7fffff] [ 0.844372] pci_bus 0000:01: resource 2 [mem 0x90400000-0x913fffff 64bit pref] [ 0.844374] pci_bus 0000:02: resource 0 [io 0x6000-0x6fff] [ 0.844376] pci_bus 0000:02: resource 1 [mem 0x9a800000-0x9b7fffff] [ 0.844378] pci_bus 0000:02: resource 2 [mem 0x91400000-0x923fffff 64bit pref] [ 0.844380] pci_bus 0000:03: resource 0 [io 0x5000-0x5fff] [ 0.844381] pci_bus 0000:03: resource 1 [mem 0x99700000-0x9a7fffff] [ 0.844383] pci_bus 0000:03: resource 2 [mem 0x92400000-0x933fffff 64bit pref] [ 0.844385] pci_bus 0000:04: resource 0 [io 0x3000-0x4fff] [ 0.844387] pci_bus 0000:04: resource 1 [mem 0x98700000-0x996fffff] [ 0.844389] pci_bus 0000:04: resource 2 [mem 0x93400000-0x944fffff 64bit pref] [ 0.844391] pci_bus 0000:05: resource 0 [io 0x2000-0x2fff] [ 0.844392] pci_bus 0000:05: resource 1 [mem 0x97600000-0x986fffff] [ 0.844394] pci_bus 0000:05: resource 2 [mem 0x94500000-0x954fffff 64bit pref] [ 0.844396] pci_bus 0000:06: resource 0 [io 0x1000-0x1fff] [ 0.844398] pci_bus 0000:06: resource 1 [mem 0x96600000-0x975fffff] [ 0.844400] pci_bus 0000:06: resource 2 [mem 0x95500000-0x964fffff 64bit pref] [ 0.844402] pci_bus 0000:09: resource 4 [io 0x0000-0x0cf7 window] [ 0.844405] pci_bus 0000:09: resource 5 [io 0x0d00-0xffff window] [ 0.844407] pci_bus 0000:09: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.844409] pci_bus 0000:09: resource 7 [mem 0x80000000-0xfebfffff window] [ 0.844530] NET: Registered protocol family 2 [ 0.844781] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.844788] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.844805] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.844833] TCP: Hash tables configured (established 8192 bind 8192) [ 0.844880] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.844888] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.844950] NET: Registered protocol family 1 [ 0.844958] NET: Registered protocol family 44 [ 0.844972] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 2.846223] pci 0000:00:1a.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.846555] pci 0000:00:1a.7: quirk_usb_early_handoff+0x0/0x6c0 took 1953752 usecs [ 4.846224] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 4.846567] pci 0000:00:1d.7: quirk_usb_early_handoff+0x0/0x6c0 took 1951385 usecs [ 4.846647] PCI: CLS 64 bytes, default 64 [ 4.846701] Unpacking initramfs... [ 5.672998] Freeing initrd memory: 38040K [ 5.673130] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 5.673132] software IO TLB: mapped [mem 0x2f5a3000-0x335a3000] (64MB) [ 5.673391] check: Scanning for low memory corruption every 60 seconds [ 5.674427] Initialise system trusted keyrings [ 5.674447] Key type blacklist registered [ 5.674515] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 5.677327] zbud: loaded [ 5.677916] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.678227] fuse init (API version 7.28) [ 5.743964] Key type asymmetric registered [ 5.743966] Asymmetric key parser 'x509' registered [ 5.743984] bounce: pool size: 64 pages [ 5.744005] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 5.744058] io scheduler mq-deadline registered [ 5.744352] pcieport 0000:00:1c.0: enabling device (0000 -> 0003) [ 5.744708] pcieport 0000:00:1c.1: enabling device (0000 -> 0003) [ 5.745861] pcieport 0000:00:1c.5: enabling device (0000 -> 0003) [ 5.746160] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.746279] vesafb: mode is 1024x768x32, linelength=4096, pages=0 [ 5.746280] vesafb: scrolling: redraw [ 5.746282] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 5.746308] vesafb: framebuffer at 0x80000000, mapped to 0x(ptrval), using 3072k, total 3072k [ 5.746465] Console: switching to colour frame buffer device 128x48 [ 5.746490] fb0: VESA VGA frame buffer device [ 5.746515] intel_idle: does not run on family 6 model 15 [ 5.890279] ACPI: AC Adapter [AC] (on-line) [ 5.890365] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 5.890377] ACPI: Power Button [PWRB] [ 5.890435] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1 [ 5.890444] ACPI: Lid Switch [LID0] [ 5.890497] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2 [ 5.890516] ACPI: Sleep Button [SLPB] [ 5.890588] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 5.890599] ACPI: Power Button [PWRF] [ 5.893802] Monitor-Mwait will be used to enter C-1 state [ 5.893813] Monitor-Mwait will be used to enter C-2 state [ 5.893822] Monitor-Mwait will be used to enter C-3 state [ 5.893828] tsc: Marking TSC unstable due to TSC halts in idle [ 5.893902] clocksource: Switched to clocksource hpet [ 5.938801] thermal LNXTHERM:00: registered as thermal_zone0 [ 5.938804] ACPI: Thermal Zone [THRM] (53 C) [ 5.938984] isapnp: Scanning for PnP cards... [ 5.939059] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 5.942023] Linux agpgart interface v0.103 [ 5.947368] loop: module loaded [ 5.947747] libphy: Fixed MDIO Bus: probed [ 5.947748] tun: Universal TUN/TAP device driver, 1.6 [ 5.947797] PPP generic driver version 2.4.2 [ 5.947860] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.947864] ehci-pci: EHCI PCI platform driver [ 5.948199] ehci-pci 0000:00:1a.7: EHCI Host Controller [ 5.948207] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 5.948223] ehci-pci 0000:00:1a.7: debug port 1 [ 5.952132] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported [ 5.952160] ehci-pci 0000:00:1a.7: irq 18, io mem 0x9c804c00 [ 5.966247] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 5.966326] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00 [ 5.966329] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 5.966331] usb usb1: Product: EHCI Host Controller [ 5.966333] usb usb1: Manufacturer: Linux 5.0.0-31-generic ehci_hcd [ 5.966334] usb usb1: SerialNumber: ... [ 5.966479] hub 1-0:1.0: USB hub found [ 5.966489] hub 1-0:1.0: 4 ports detected [ 5.966955] ehci-pci 0000:00:1d.7: EHCI Host Controller [ 5.966961] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 5.966975] ehci-pci 0000:00:1d.7: debug port 1 [ 5.970897] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported [ 5.970911] ehci-pci 0000:00:1d.7: irq 20, io mem 0x9c804800 [ 5.986243] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 5.986302] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00 [ 5.986304] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 5.986306] usb usb2: Product: EHCI Host Controller [ 5.986308] usb usb2: Manufacturer: Linux 5.0.0-31-generic ehci_hcd [ 5.986310] usb usb2: SerialNumber: ... [ 5.986436] hub 2-0:1.0: USB hub found [ 5.986445] hub 2-0:1.0: 8 ports detected [ 5.986753] ehci-platform: EHCI generic platform driver [ 5.986780] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.986784] ohci-pci: OHCI PCI platform driver [ 5.986801] ohci-platform: OHCI generic platform driver [ 5.986814] uhci_hcd: USB Universal Host Controller Interface driver [ 5.987060] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 5.987066] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 5.987074] uhci_hcd 0000:00:1a.0: detected 2 ports [ 5.987107] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000080e0 [ 5.987173] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 5.987176] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 5.987178] usb usb3: Product: UHCI Host Controller [ 5.987179] usb usb3: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 5.987181] usb usb3: SerialNumber: ... [ 5.987308] hub 3-0:1.0: USB hub found [ 5.987318] hub 3-0:1.0: 2 ports detected [ 5.987689] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 5.987696] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 5.987704] uhci_hcd 0000:00:1a.1: detected 2 ports [ 5.987735] uhci_hcd 0000:00:1a.1: irq 17, io base 0x000080c0 [ 5.987801] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 5.987804] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 5.987806] usb usb4: Product: UHCI Host Controller [ 5.987807] usb usb4: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 5.987809] usb usb4: SerialNumber: ... [ 5.987938] hub 4-0:1.0: USB hub found [ 5.987947] hub 4-0:1.0: 2 ports detected [ 6.031820] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 6.031827] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5 [ 6.031835] uhci_hcd 0000:00:1d.0: detected 2 ports [ 6.031858] uhci_hcd 0000:00:1d.0: irq 20, io base 0x000080a0 [ 6.031925] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 6.031927] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 6.031929] usb usb5: Product: UHCI Host Controller [ 6.031931] usb usb5: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 6.031933] usb usb5: SerialNumber: ... [ 6.032060] hub 5-0:1.0: USB hub found [ 6.032069] hub 5-0:1.0: 2 ports detected [ 6.082110] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 6.082116] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6 [ 6.082124] uhci_hcd 0000:00:1d.1: detected 2 ports [ 6.082155] uhci_hcd 0000:00:1d.1: irq 22, io base 0x00008080 [ 6.082353] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 6.082356] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 6.082358] usb usb6: Product: UHCI Host Controller [ 6.082360] usb usb6: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 6.082362] usb usb6: SerialNumber: ... [ 6.082503] hub 6-0:1.0: USB hub found [ 6.082514] hub 6-0:1.0: 2 ports detected [ 6.082893] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 6.082899] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7 [ 6.082907] uhci_hcd 0000:00:1d.2: detected 2 ports [ 6.082931] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008060 [ 6.083012] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 6.083015] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 6.083017] usb usb7: Product: UHCI Host Controller [ 6.083018] usb usb7: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 6.083020] usb usb7: SerialNumber: ... [ 6.083154] hub 7-0:1.0: USB hub found [ 6.083164] hub 7-0:1.0: 2 ports detected [ 6.083534] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 6.083540] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 8 [ 6.083548] uhci_hcd 0000:00:1d.3: detected 2 ports [ 6.083590] uhci_hcd 0000:00:1d.3: irq 19, io base 0x00008040 [ 6.083671] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.00 [ 6.083674] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=... [ 6.083675] usb usb8: Product: UHCI Host Controller [ 6.083677] usb usb8: Manufacturer: Linux 5.0.0-31-generic uhci_hcd [ 6.083679] usb usb8: SerialNumber: ... [ 6.083808] hub 8-0:1.0: USB hub found [ 6.083819] hub 8-0:1.0: 2 ports detected [ 6.084053] i8042: PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUE] at 0x60,0x64 irq 1,12 [ 6.123902] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 6.123907] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 6.124084] mousedev: PS/2 mouse device common for all mice [ 6.127769] rtc_cmos 00:01: RTC can wake from S4 [ 6.127954] rtc_cmos 00:01: registered as rtc0 [ 6.127982] rtc_cmos 00:01: alarms up to one month, 242 bytes nvram, hpet irqs [ 6.127993] i2c /dev entries driver [ 6.128136] device-mapper: uevent: version 1.0.3 [ 6.128221] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: XXX@XXX [ 6.128255] platform eisa.0: Probing EISA bus 0 [ 6.128258] platform eisa.0: EISA: Cannot allocate resource for mainboard [ 6.128260] platform eisa.0: Cannot allocate resource for EISA slot 1 [ 6.128262] platform eisa.0: Cannot allocate resource for EISA slot 2 [ 6.128263] platform eisa.0: Cannot allocate resource for EISA slot 3 [ 6.128265] platform eisa.0: Cannot allocate resource for EISA slot 4 [ 6.128267] platform eisa.0: Cannot allocate resource for EISA slot 5 [ 6.128269] platform eisa.0: Cannot allocate resource for EISA slot 6 [ 6.128270] platform eisa.0: Cannot allocate resource for EISA slot 7 [ 6.128272] platform eisa.0: Cannot allocate resource for EISA slot 8 [ 6.128274] platform eisa.0: EISA: Detected 0 cards [ 6.128282] cpufreq_nforce2: No nForce2 chipset [ 6.162767] ledtrig-cpu: registered to indicate activity on CPUs [ 6.163181] NET: Registered protocol family 10 [ 6.164507] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 6.175689] Segment Routing with IPv6 [ 6.175726] NET: Registered protocol family 17 [ 6.175776] Key type dns_resolver registered [ 6.249971] isapnp: No Plug & Play device found [ 6.250294] mce: Using 6 MCE banks [ 6.250371] microcode: sig=0x6fd, pf=0x80, revision=0xa4 [ 6.250442] microcode: Microcode Update Driver: v2.2. [ 6.250448] Using IPI No-Shortcut mode [ 6.250730] registered taskstats version 1 [ 6.250743] Loading compiled-in X.509 certificates [ 6.257337] Loaded X.509 cert 'Build time autogenerated kernel key: 1b9a265f05101510b5be50142f325f3648e0e262' [ 6.257370] zswap: loaded using pool lzo/zbud [ 6.262267] battery: ACPI: Battery Slot [BAT0] (battery present) [ 6.267154] Key type big_key registered [ 6.267160] Key type trusted registered [ 6.271784] Key type encrypted registered [ 6.271789] AppArmor: AppArmor sha1 policy hashing enabled [ 6.271798] ima: No TPM chip found, activating TPM-bypass! [ 6.271804] ima: Allocated hash algorithm: sha1 [ 6.271814] No architecture policies found [ 6.271829] evm: Initialising EVM extended attributes: [ 6.271830] evm: security.selinux [ 6.271831] evm: security.SMACK64 [ 6.271832] evm: security.SMACK64EXEC [ 6.271833] evm: security.SMACK64TRANSMUTE [ 6.271834] evm: security.SMACK64MMAP [ 6.271834] evm: security.apparmor [ 6.271835] evm: security.ima [ 6.271836] evm: security.capability [ 6.271837] evm: HMAC attrs: 0x1 [ 6.272291] Magic number: 7:782:175 [ 6.272298] misc network_throughput: hash matches [ 6.272382] acpi device:0b: hash matches [ 6.272452] rtc_cmos 00:01: setting system clock to 2019-10-13T11:11:20 UTC (1570965080) [ 6.272946] Unstable clock detected, switching default tracing clock to "global" [ 6.272946] If you want to keep using the local clock, then add: [ 6.272946] "trace_clock=local" [ 6.272946] on the kernel command line [ 6.275563] Freeing unused kernel image memory: 1128K [ 6.290387] Write protecting kernel text and read-only data: 13128k [ 6.290389] NX-protecting the kernel data: 6916k [ 6.290885] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 6.290941] x86/mm: Checking user space page tables [ 6.291021] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 6.291023] Run /init as init process [ 6.510261] usb 5-1: new low-speed USB device number 2 using uhci_hcd [ 6.518255] usb 3-2: new full-speed USB device number 2 using uhci_hcd [ 6.582246] random: fast init done [ 6.698420] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.698466] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.698474] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.702272] usb 5-1: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00 [ 6.702275] usb 5-1: New USB device strings: Mfr=0, Product=1, SerialNumber=... [ 6.702277] usb 5-1: Product: USB OPTICAL MOUSE [ 6.704319] usb 3-2: New USB device found, idVendor=138a, idProduct=0001, bcdDevice= 3.72 [ 6.704321] usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=... [ 6.741888] acpi PNP0C14:01: duplicate WMI GUID HASH_221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00) [ 6.765910] sdhci: Secure Digital Host Controller Interface driver [ 6.765913] sdhci: Copyright(c) Pierre Ossman [ 6.778109] sdhci-pci 0000:05:00.0: SDHCI controller found [197b:2382] (rev 0) [ 6.778486] mmc0: SDHCI controller on PCI [0000:05:00.0] using ADMA [ 6.778512] sdhci-pci 0000:05:00.2: SDHCI controller found [197b:2381] (rev 0) [ 6.778595] sdhci-pci 0000:05:00.2: Refusing to bind to secondary interface. [ 6.784422] ahci 0000:00:1f.2: version 3.0 [ 6.784866] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 6.784869] ahci 0000:00:1f.2: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc ems sxs [ 6.790959] r8169 0000:04:00.0: can't disable ASPM; OS doesn't have ASPM control [ 6.793234] libphy: r8169: probed [ 6.793475] r8169 0000:04:00.0 eth0: RTL8102e, XX:XX:XX:XX:XX:XX, XID 24a, IRQ 19 [ 6.819267] scsi host0: ahci [ 6.819538] scsi host1: ahci [ 6.819737] scsi host2: ahci [ 6.819937] scsi host3: ahci [ 6.820142] scsi host4: ahci [ 6.820355] scsi host5: ahci [ 6.820486] ata1: SATA max UDMA/133 abar m2048@0x9c804000 port 0x9c804100 irq 24 [ 6.820489] ata2: SATA max UDMA/133 abar m2048@0x9c804000 port 0x9c804180 irq 24 [ 6.820490] ata3: DUMMY [ 6.820491] ata4: DUMMY [ 6.820494] ata5: SATA max UDMA/133 abar m2048@0x9c804000 port 0x9c804300 irq 24 [ 6.820497] ata6: SATA max UDMA/133 abar m2048@0x9c804000 port 0x9c804380 irq 24 [ 6.847334] hidraw: raw HID events driver (C) Jiri Kosina [ 6.858411] r8169 0000:04:00.0 enp4s0: renamed from eth0 [ 6.875031] usbcore: registered new interface driver usbhid [ 6.875033] usbhid: USB HID core driver [ 6.884224] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/0003:275D:0BA6.0001/input/input7 [ 6.884365] hid-generic 0003:275D:0BA6.0001: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:1d.0-1/input0 [ 7.118258] usb 2-5: new high-speed USB device number 3 using ehci-pci [ 7.137378] ata6: SATA link down (SStatus 0 SControl 300) [ 7.137413] ata5: SATA link down (SStatus 0 SControl 300) [ 7.226285] usb 1-3: new high-speed USB device number 3 using ehci-pci [ 7.294301] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7.295229] ata1.00: ACPI cmd 00/XX:XX:XX:XX:XX:XX (NOP) rejected by device (Stat=0x51 Err=0x04) [ 7.295356] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.295479] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.295484] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) filtered out [ 7.295616] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.295745] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.296261] ata1.00: ATA-8: FUJITSU MHZ2160BH G2, 8909, max UDMA/100 [ 7.296270] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 7.297215] ata1.00: ACPI cmd 00/XX:XX:XX:XX:XX:XX (NOP) rejected by device (Stat=0x51 Err=0x04) [ 7.297348] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.297352] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) filtered out [ 7.297481] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.297619] ata1.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) succeeded [ 7.298126] ata1.00: configured for UDMA/100 [ 7.298259] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 7.302995] usb 2-5: New USB device found, idVendor=046d, idProduct=09b8, bcdDevice=60.51 [ 7.302999] usb 2-5: New USB device strings: Mfr=0, Product=2, SerialNumber=... [ 7.303003] usb 2-5: Product: HP Webcam [ 7.308715] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHZ2160B 8909 PQ: 0 ANSI: 5 [ 7.309069] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 7.309260] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 7.309280] sd 0:0:0:0: [sda] Write Protect is off [ 7.309282] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 7.309317] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.311638] ata2.00: ACPI cmd 00/XX:XX:XX:XX:XX:XX (NOP) succeeded [ 7.311998] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.312344] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.312349] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) filtered out [ 7.312690] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.313027] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.326001] ata2.00: ATAPI: Optiarc DVD RW AD-7561S, AH03, max UDMA/100 [ 7.340278] ata2.00: ACPI cmd 00/XX:XX:XX:XX:XX:XX (NOP) succeeded [ 7.340697] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.341065] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.341069] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) filtered out [ 7.341393] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.341777] ata2.00: ACPI cmd ef/XX:XX:XX:XX:XX:XX (SET FEATURES) rejected by device (Stat=0x51 Err=0x04) [ 7.354443] ata2.00: configured for UDMA/100 [ 7.366763] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7561S AH03 PQ: 0 ANSI: 5 [ 7.389527] sda: sda1 [ 7.390254] sd 0:0:0:0: [sda] Attached SCSI disk [ 7.391851] usb 1-3: New USB device found, idVendor=03f0, idProduct=201d, bcdDevice= 0.01 [ 7.391855] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=... [ 7.391859] usb 1-3: Product: HP un2400 Mobile Broadband Module [ 7.391862] usb 1-3: Manufacturer: HP un2400 Mobile Broadband Module [ 7.425893] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 7.425896] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 7.426266] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 7.426392] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 8.501300] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6 [ 8.574818] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) [ 9.867620] random: crng init done [ 9.867625] random: 7 urandom warning(s) missed due to ratelimiting [ 10.882053] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid) [ 10.898411] systemd[1]: Detected architecture x86. [ 10.912574] systemd[1]: Set hostname to ... [ 13.368919] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 13.369270] systemd[1]: Set up automount ... [ 13.369602] systemd[1]: Created slice User and Session Slice. [ 13.369647] systemd[1]: Reached target Remote File Systems. [ 13.369686] systemd[1]: Reached target User and Group Name Lookups. [ 13.369950] systemd[1]: Created slice System Slice. [ 13.370107] systemd[1]: Listening on LVM2 metadata daemon socket. [ 13.903778] lp: driver loaded but no devices found [ 13.925857] ppdev: user-space parallel port driver [ 14.311614] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro [ 14.646388] systemd-journald[337]: Received request to flush runtime journal from PID 1 [ 19.355506] ene_ir: chip is 0x3926 - kbver = 0x00, rev = 0xc0 [ 19.355508] ene_ir: PLL freq = 1406 [ 19.355509] ene_ir: KB3926C detected [ 19.355524] ene_ir: Firmware regs: c1 01 [ 19.355525] ene_ir: Hardware features: [ 19.355526] ene_ir: * Uses GPIO 40 for IR demodulated input [ 19.670243] Registered IR keymap rc-rc6-mce [ 19.803491] hp_accel: laptop model unknown, using default axes configuration [ 19.804156] lis3lv02d: 8 bits sensor found [ 19.813913] IR RC6 protocol handler initialized [ 19.842343] rc rc0: ENE eHome Infrared Remote Receiver as /devices/virtual/rc/rc0 [ 19.842433] input: ENE eHome Infrared Remote Receiver as /devices/virtual/rc/rc0/input8 [ 19.842603] rc rc0: lirc_dev: driver ene_ir registered at minor = 0, raw IR receiver, no transmitter [ 19.842676] ene_ir: driver has been successfully loaded [ 19.842981] rc rc0: nonsensical timing event of duration 0 [ 19.842983] rc rc0: two consecutive events of type space [ 19.850334] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input9 [ 20.039162] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 20.053493] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 20.054937] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMBA) (20181213/utaddress-213) [ 20.054944] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 20.054947] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20181213/utaddress-213) [ 20.054952] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 20.054953] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x000000000000053B (\GPIO) (20181213/utaddress-213) [ 20.054957] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 20.054958] lpc_ich: Resource conflict(s) found affecting gpio_ich [ 20.243436] input: HP WMI hotkeys as /devices/virtual/input/input10 [ 20.369502] wl: loading out-of-tree module taints kernel. [ 20.369508] wl: module license 'MIXED/Proprietary' taints kernel. [ 20.369509] Disabling lock debugging due to kernel taint [ 20.378000] wl: module verification failed: signature and/or required key missing - tainting kernel [ 20.407723] wlan0: Broadcom BCM4315 802.11 Hybrid Wireless Controller XXX.XXX.XXX.XXX (r587334) [ 21.026885] pci 0000:00:00.0: Intel GM45 Chipset [ 21.026914] pci 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 21.027380] pci 0000:00:00.0: detected 32768K stolen memory [ 21.027598] checking generic (80000000 300000) vs hw (80000000 10000000) [ 21.027599] fb0: switching to inteldrmfb from VESA VGA [ 21.027634] Console: switching to colour dummy device 80x25 [ 21.031456] [drm] Replacing VGA console driver [ 21.032427] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 21.032429] [drm] Driver supports precise vblank timestamp query. [ 21.033556] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 21.069978] [drm] RC6 disabled, disabling runtime PM support [ 21.071854] [drm] Initialized i915 1.6.0 20181204 for 0000:00:02.0 on minor 0 [ 21.072801] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no) [ 21.098910] acpi device:02: registered as cooling_device3 [ 21.099000] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input11 [ 21.110000] usbcore: registered new interface driver usbserial_generic [ 21.110013] usbserial: USB Serial support registered for generic [ 21.115730] intel_powerclamp: No package C-state available [ 21.147677] intel_powerclamp: No package C-state available [ 21.194532] fbcon: inteldrmfb (fb0) is primary device [ 21.194611] Console: switching to colour frame buffer device 160x50 [ 21.194648] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device [ 21.207468] media: Linux media interface: v0.10 [ 21.226095] usbcore: registered new interface driver qcserial [ 21.226117] usbserial: USB Serial support registered for Qualcomm USB modem [ 21.227232] qcserial 1-3:1.0: Qualcomm USB modem converter detected [ 21.227342] usb 1-3: Qualcomm USB modem converter now attached to ttyUSB0 [ 21.291521] wl 0000:03:00.0 wlp3s0: renamed from wlan0 [ 21.364265] usb 1-3: USB disconnect, device number 3 [ 21.364472] qcserial ttyUSB0: Qualcomm USB modem converter now disconnected from ttyUSB0 [ 21.364501] qcserial 1-3:1.0: device disconnected [ 21.365185] snd_hda_codec_idt hdaudioC0D0: autoconfig for 92HD71B7X: line_outs=1 (0xd/0x0/0x0/0x0/0x0) type:speaker [ 21.365188] snd_hda_codec_idt hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 21.365190] snd_hda_codec_idt hdaudioC0D0: hp_outs=1 (0xa/0x0/0x0/0x0/0x0) [ 21.365192] snd_hda_codec_idt hdaudioC0D0: mono: mono_out=0x0 [ 21.365194] snd_hda_codec_idt hdaudioC0D0: inputs: [ 21.365196] snd_hda_codec_idt hdaudioC0D0: Internal Mic=0x18 [ 21.365198] snd_hda_codec_idt hdaudioC0D0: Mic=0xb [ 21.419995] videodev: Linux video capture interface: v2.00 [ 21.474427] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 21.474518] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 21.474600] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14 [ 22.242775] uvcvideo: Found UVC 1.00 device HP Webcam (046d:09b8) [ 22.256197] uvcvideo 2-5:1.0: Entity type for entity Processing 3 was not initialized! [ 22.256201] uvcvideo 2-5:1.0: Entity type for entity Camera 1 was not initialized! [ 22.256203] uvcvideo 2-5:1.0: Entity type for entity Extension 4 was not initialized! [ 22.256205] uvcvideo 2-5:1.0: Entity type for entity Extension 13 was not initialized! [ 22.256207] uvcvideo 2-5:1.0: Entity type for entity Extension 12 was not initialized! [ 22.256209] uvcvideo 2-5:1.0: Entity type for entity Extension 10 was not initialized! [ 22.256211] uvcvideo 2-5:1.0: Entity type for entity Extension 14 was not initialized! [ 22.256326] input: HP Webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-5/2-5:1.0/input/input15 [ 22.256434] usbcore: registered new interface driver uvcvideo [ 22.256435] USB Video Class driver (1.1.1) [ 22.534257] usb 1-3: new high-speed USB device number 4 using ehci-pci [ 22.695609] usb 1-3: New USB device found, idVendor=03f0, idProduct=201d, bcdDevice= 0.01 [ 22.695614] usb 1-3: New USB device strings: Mfr=2, Product=1, SerialNumber=... [ 22.695618] usb 1-3: Product: HP un2400 Mobile Broadband Module [ 22.695621] usb 1-3: Manufacturer: HP un2400 Mobile Broadband Module [ 22.697299] qcserial 1-3:1.0: Qualcomm USB modem converter detected [ 22.697460] usb 1-3: Qualcomm USB modem converter now attached to ttyUSB0 [ 24.250260] Adding 999420k swap on /dev/mapper/XXXXXXXXXXXXXXXXXXX Priority:-2 extents:1 across:999420k FS [ 34.959724] RTL8201CP Ethernet r8169-400:00: attached PHY driver [RTL8201CP Ethernet] (mii_bus:phy_addr=r8169-400:00, irq=IGNORE) [ 35.059519] r8169 0000:04:00.0 enp4s0: Link is Down [ 40.144303] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready [ 7707.962354] perf: interrupt took too long (2549 > 2500), lowering kernel.perf_event_max_sample_rate to 78250 [10717.726446] perf: interrupt took too long (3205 > 3186), lowering kernel.perf_event_max_sample_rate to 62250 [14953.944740] perf: interrupt took too long (4042 > 4006), lowering kernel.perf_event_max_sample_rate to 49250 [21184.070602] perf: interrupt took too long (5056 > 5052), lowering kernel.perf_event_max_sample_rate to 39500 [21289.290483] usb 2-2: new high-speed USB device number 4 using ehci-pci [21289.460275] usb 2-2: New USB device found, idVendor=152d, idProduct=2329, bcdDevice= 1.00 [21289.460283] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=... [21289.460288] usb 2-2: Product: USB to ATA/ATAPI bridge [21289.460293] usb 2-2: Manufacturer: JMicron [21289.460298] usb 2-2: SerialNumber: ... [21289.628970] usb-storage 2-2:1.0: USB Mass Storage device detected [21289.629120] usb-storage 2-2:1.0: Quirks match for vid 152d pid 2329: 8020 [21289.629167] scsi host6: usb-storage 2-2:1.0 [21289.629299] usbcore: registered new interface driver usb-storage [21289.654728] usbcore: registered new interface driver uas [21290.635266] scsi 6:0:0:0: Direct-Access SAMSUNG HN-M500MBB 2AR1 PQ: 0 ANSI: 2 CCS [21290.636201] sd 6:0:0:0: Attached scsi generic sg2 type 0 [21290.641692] sd 6:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB) [21290.642788] sd 6:0:0:0: [sdb] Write Protect is off [21290.642795] sd 6:0:0:0: [sdb] Mode Sense: 28 00 00 00 [21290.643918] sd 6:0:0:0: [sdb] No Caching mode page found [21290.643930] sd 6:0:0:0: [sdb] Assuming drive cache: write through [21290.690952] sdb: sdb1 sdb2 sdb3 [21290.694391] sd 6:0:0:0: [sdb] Attached SCSI disk [21302.998139] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null) [21309.962565] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null) [21573.182664] usb 5-1: USB disconnect, device number 2 [21574.989010] usb 2-2: USB disconnect, device number 4 [21575.020706] FAT-fs (sdb1): unable to read boot sector to mark fs as dirty [21575.052646] Buffer I/O error on dev sdb2, logical block 262144, lost sync page write [21575.052653] JBD2: Error -5 detected when updating journal superblock for sdb2-8. [21575.052655] Aborting journal on device sdb2-8. [21575.052659] Buffer I/O error on dev sdb2, logical block 262144, lost sync page write [21575.052661] JBD2: Error -5 detected when updating journal superblock for sdb2-8. [21575.082286] Buffer I/O error on dev sdb3, logical block 7372800, lost sync page write [21575.082291] JBD2: Error -5 detected when updating journal superblock for sdb3-8. [21575.082293] Aborting journal on device sdb3-8. [21575.082297] Buffer I/O error on dev sdb3, logical block 7372800, lost sync page write [21575.082299] JBD2: Error -5 detected when updating journal superblock for sdb3-8. [21580.062486] usb 2-1: new high-speed USB device number 5 using ehci-pci [21580.231707] usb 2-1: New USB device found, idVendor=152d, idProduct=2329, bcdDevice= 1.00 [21580.231715] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=... [21580.231720] usb 2-1: Product: USB to ATA/ATAPI bridge [21580.231725] usb 2-1: Manufacturer: JMicron [21580.231729] usb 2-1: SerialNumber: ... [21580.232809] usb-storage 2-1:1.0: USB Mass Storage device detected [21580.237456] usb-storage 2-1:1.0: Quirks match for vid 152d pid 2329: 8020 [21580.239285] scsi host6: usb-storage 2-1:1.0 [21581.263542] scsi 6:0:0:0: Direct-Access SAMSUNG HN-M500MBB 2AR1 PQ: 0 ANSI: 2 CCS [21581.264414] sd 6:0:0:0: Attached scsi generic sg2 type 0 [21581.272788] sd 6:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/466 GiB) [21581.274149] sd 6:0:0:0: [sdb] Write Protect is off [21581.274152] sd 6:0:0:0: [sdb] Mode Sense: 28 00 00 00 [21581.275189] sd 6:0:0:0: [sdb] No Caching mode page found [21581.275194] sd 6:0:0:0: [sdb] Assuming drive cache: write through [21581.301369] sdb: sdb1 sdb2 sdb3 [21581.305072] sd 6:0:0:0: [sdb] Attached SCSI disk [21587.068513] FAT-fs (sdb1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [21593.004675] EXT4-fs (sdb2): recovery complete [21593.005290] EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null) [21599.999432] EXT4-fs (sdb3): recovery complete [21599.999939] EXT4-fs (sdb3): mounted filesystem with ordered data mode. Opts: (null) [21624.254490] usb 2-2: new high-speed USB device number 6 using ehci-pci [21624.419204] usb 2-2: New USB device found, idVendor=1908, idProduct=0226, bcdDevice= 1.11 [21624.419213] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=... [21624.419862] usb-storage 2-2:1.0: USB Mass Storage device detected [21624.420248] scsi host7: usb-storage 2-2:1.0 [21625.451320] scsi 7:0:0:0: Direct-Access Generic Mass-Storage 1.11 PQ: 0 ANSI: 2 [21625.452312] sd 7:0:0:0: Attached scsi generic sg3 type 0 [21626.460832] sd 7:0:0:0: [sdc] 262144000 512-byte logical blocks: (134 GB/125 GiB) [21626.461807] sd 7:0:0:0: [sdc] Write Protect is off [21626.461811] sd 7:0:0:0: [sdc] Mode Sense: 03 00 00 00 [21626.463924] sd 7:0:0:0: [sdc] No Caching mode page found [21626.463929] sd 7:0:0:0: [sdc] Assuming drive cache: write through [21626.474931] sd 7:0:0:0: [sdc] Attached SCSI removable disk [22382.548752] usb 2-2: USB disconnect, device number 6 [22386.514481] usb 2-2: new high-speed USB device number 7 using ehci-pci [22386.682995] usb 2-2: New USB device found, idVendor=1908, idProduct=0226, bcdDevice= 1.11 [22386.683004] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=... [22386.683602] usb-storage 2-2:1.0: USB Mass Storage device detected [22386.683994] scsi host7: usb-storage 2-2:1.0 [22387.695429] scsi 7:0:0:0: Direct-Access Generic Mass-Storage 1.11 PQ: 0 ANSI: 2 [22387.696264] sd 7:0:0:0: Attached scsi generic sg3 type 0 [22399.290511] sd 7:0:0:0: [sdc] Attached SCSI removable disk [22404.972009] usb 2-1: USB disconnect, device number 5 [22405.022022] Buffer I/O error on dev sdb2, logical block 262144, lost sync page write [22405.022028] JBD2: Error -5 detected when updating journal superblock for sdb2-8. [22405.022030] Aborting journal on device sdb2-8. [22405.022034] Buffer I/O error on dev sdb2, logical block 262144, lost sync page write [22405.022036] JBD2: Error -5 detected when updating journal superblock for sdb2-8. [22408.698315] usb 5-1: new low-speed USB device number 3 using uhci_hcd [22408.898346] usb 5-1: New USB device found, idVendor=275d, idProduct=0ba6, bcdDevice= 1.00 [22408.898351] usb 5-1: New USB device strings: Mfr=0, Product=1, SerialNumber=... [22408.898354] usb 5-1: Product: USB OPTICAL MOUSE [22408.916576] input: USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb5/5-1/5-1:1.0/0003:275D:0BA6.0002/input/input16 [22408.916751] hid-generic 0003:275D:0BA6.0002: input,hidraw0: USB HID v1.11 Mouse [USB OPTICAL MOUSE ] on usb-0000:00:1d.0-1/input0 [22409.802132] usb usb2-port2: disabled by hub (EMI?), re-enabling... [22409.802146] usb 2-2: USB disconnect, device number 7 [22409.814281] scsi 7:0:0:0: rejecting I/O to dead device [22465.318480] usb 2-2: new high-speed USB device number 9 using ehci-pci [22465.487310] usb 2-2: New USB device found, idVendor=1908, idProduct=0226, bcdDevice= 1.11 [22465.487319] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=... [22465.487976] usb-storage 2-2:1.0: USB Mass Storage device detected [22465.494473] scsi host6: usb-storage 2-2:1.0 [22466.511443] scsi 6:0:0:0: Direct-Access Generic Mass-Storage 1.11 PQ: 0 ANSI: 2 [22466.514655] sd 6:0:0:0: Attached scsi generic sg2 type 0 [22467.522959] sd 6:0:0:0: [sdb] 262144000 512-byte logical blocks: (134 GB/125 GiB) [22467.524060] sd 6:0:0:0: [sdb] Write Protect is off [22467.524064] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 [22467.525061] sd 6:0:0:0: [sdb] No Caching mode page found [22467.525074] sd 6:0:0:0: [sdb] Assuming drive cache: write through [22467.537179] sd 6:0:0:0: [sdb] Attached SCSI removable disk [23305.710930] usb 2-5: reset high-speed USB device number 3 using ehci-pci [23323.994347] mce: CPU0: Core temperature above threshold, cpu clock throttled (total events = 1) [23323.994992] mce: CPU0: Core temperature/speed normal [23346.796878] mce: CPU1: Core temperature above threshold, cpu clock throttled (total events = 1) [23346.797522] mce: CPU1: Core temperature/speed normal